STM32——IIC

STM32——IIC

1.用到的库函数

HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef *hi2c,uint16_t DevAddress,uint16_t MemAddress,uint16_t MemAddSize,uint8_t *pData,uint16_t Size,uint32_t Timeout)

参数一：I2C_HandleTypeDef *hi2c，I2C设备句柄

参数二：uint16_t DevAddress，目标器件的地址，七位地址必须左对齐

参数三：uint16_t MemAddress，目标器件的目标寄存器地址

参数四：uint16_t MemAddSize，目标器件内部寄存器地址数据长度

参数五：uint8_t *pData，待写的数据首地址

参数六：uint16_t Size，待写的数据长度

参数七：uint32_t Timeout，超时时间

返回值：HAL_StatusTypeDef，HAL状态（OK，busy，ERROR，TIMEOUT）

OLED写命令的封装

void Oled_Write_Cmd(uint8_t dataCmd)
{HAL_I2C_Mem_Write(&hi2c1, 0x78, 0x00, I2C_MEMADD_SIZE_8BIT,&dataCmd, 1, 0xff);
}

OLED写数据的封装

void Oled_Write_Data(uint8_t dataData)
{
HAL_I2C_Mem_Write(&hi2c1, 0x78, 0x40, I2C_MEMADD_SIZE_8BIT,
&dataData, 1, 0xff);
}

2.OLED显示图片

接线：

SCL – PB6

SDA – PB7

代码实现

    void Oled_Write_Cmd(uint8_t dataCmd){HAL_I2C_Mem_Write(&hi2c1, 0x78, 0x00, I2C_MEMADD_SIZE_8BIT,&dataCmd, 1, 0xff);}void Oled_Write_Data(uint8_t dataData){HAL_I2C_Mem_Write(&hi2c1, 0x78, 0x40, I2C_MEMADD_SIZE_8BIT,&dataData, 1, 0xff);}void Oled_Init(void){Oled_Write_Cmd(0xAE);//--display offOled_Write_Cmd(0x00);//---set low column addressOled_Write_Cmd(0x10);//---set high column addressOled_Write_Cmd(0x40);//--set start line addressOled_Write_Cmd(0xB0);//--set page addressOled_Write_Cmd(0x81); // contract controlOled_Write_Cmd(0xFF);//--128Oled_Write_Cmd(0xA1);//set segment remapOled_Write_Cmd(0xA6);//--normal / reverseOled_Write_Cmd(0xA8);//--set multiplex ratio(1 to 64)Oled_Write_Cmd(0x3F);//--1/32 dutyOled_Write_Cmd(0xC8);//Com scan directionOled_Write_Cmd(0xD3);//-set display offsetOled_Write_Cmd(0x00);//Oled_Write_Cmd(0xD5);//set osc divisionOled_Write_Cmd(0x80);//Oled_Write_Cmd(0xD8);//set area color mode offOled_Write_Cmd(0x05);//Oled_Write_Cmd(0xD9);//Set Pre-Charge PeriodOled_Write_Cmd(0xF1);//Oled_Write_Cmd(0xDA);//set com pin configuartionOled_Write_Cmd(0x12);//Oled_Write_Cmd(0xDB);//set VcomhOled_Write_Cmd(0x30);//Oled_Write_Cmd(0x8D);//set charge pump enableOled_Write_Cmd(0x14);//Oled_Write_Cmd(0xAF);//--turn on oled panel}void Oled_Screen_Clear(void){int i,n;Oled_Write_Cmd (0x20); //set memory addressing modeOled_Write_Cmd (0x02); //page addressing modefor(i=0;i<8;i++){Oled_Write_Cmd(0xb0+i); //éè??ò3μ??·￡¨0~7￡?Oled_Write_Cmd(0x00); //éè????ê??????aáDμíμ??·Oled_Write_Cmd(0x10); //éè????ê??????aáD??μ??·for(n=0;n<128;n++)Oled_Write_Data(0x00);}}unsigned char bmpImager[] = {/*-- 调入了一幅图像：D:\无标题.bmp --*//*-- 宽度x高度=128x64 --128x8x8*/0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x08,0x0C,0x04,0x06,0x06,0x0C,0x04,0x0C,0xFC,0x1C,0x74,0xFC,0xF8,0xF0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x07,0x04,0x88,0xF8,0x08,0x08,0x0C,0x06,0x01,0x00,0x00,0x01,0x1F,0x7F,0xFF,0xDC,0xF8,0xE0,0xC0,0x40,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x10,0x18,0x08,0x0C,0x04,0x04,0x06,0x02,0x01,0x01,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x60,0xC0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x06,0x1C,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x07,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x88,0xE8,0x38,0x0E,0x09,0x08,0x08,0x88,0xE8,0x18,0x08,0x08,0x08,0x00,0x00,0xFF,0x89,0x89,0x89,0xFF,0x00,0xFF,0x89,0x89,0x89,0x89,0xFF,0x00,0x00,0x04,0x04,0x84,0x74,0x6F,0xA4,0x24,0x24,0x24,0x24,0xA4,0x64,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xF0,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x10,0x10,0x08,0x09,0x09,0x06,0x06,0x06,0x05,0x08,0x08,0x10,0x10,0x00,0x00,0x0C,0x03,0x10,0x10,0x10,0x1F,0x18,0x07,0x00,0x00,0x10,0x10,0x1F,0x00,0x10,0x08,0x06,0x11,0x10,0x08,0x09,0x0A,0x06,0x06,0x0B,0x08,0x10,0x10,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x1E,0x03,0x00,0x00,0xC0,0x60,0x30,0x0C,0x04,0x06,0x02,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x1E,0x60,0x78,0x0F,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,};void Oled_Show_Image(unsigned char *image){unsigned char i;unsigned int j;for(i=0;i<8;i++){Oled_Write_Cmd(0xB0 + i);//page0--page7//每个page从0列Oled_Write_Cmd(0x00);Oled_Write_Cmd(0x10);//0到127列，依次写入0，每写入数据，列地址自动偏移for(j = 128 * i; j<(128 * (i+1));j++){Oled_Write_Data(image[j]);}}}int main(void){/* USER CODE BEGIN 1 *//* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_I2C1_Init();/* USER CODE BEGIN 2 *///1. OLED初始化Oled_Init();//2. 选择一个位置//2.1 确认页寻址模式Oled_Write_Cmd(0x20);Oled_Write_Cmd(0x02);Oled_Screen_Clear();Oled_Show_Image(bmpImager);/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */}

本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若转载，请注明出处：http://www.mzph.cn/news/659321.shtml

如若内容造成侵权/违法违规/事实不符，请联系多彩编程网进行投诉反馈email:809451989@qq.com，一经查实，立即删除！

相关文章

js中数组的常用处理方法

js中数组的常用处理方法

1.归纳 方法作用说明返回值是否修改原数组forEach遍历数组遍历数组并对每一个元素进行操作无/undefined视具体处理而定filter过滤数组返回一个满足筛选条件的新数组新数组否map映射数组按照规则对原数组的元素进行映射新数组否reduce累计器返回累计处理的结果,常用于求和一般为…
阅读更多...
【ARM Trace32(劳特巴赫) 使用介绍 3.1 -- 不 attach core 直接访问 memory】

【ARM Trace32(劳特巴赫) 使用介绍 3.1 -- 不 attach core 直接访问 memory】

文章目录 背景介绍背景介绍 在使用 trace32 时在有些场景需要不 attach core 然后去读写 memory，比如在某些情况下 core 已经挂死连接不上了，这个时候需要dump内存，这个时候需要怎做呢？ print "test for memory access directly";SYStem.OPTION WAITRESET OF…
阅读更多...
推荐系统｜排序_多目标模型

推荐系统｜排序_多目标模型

文章目录 四大特征用户特征物品特征统计特征场景特征 训练过程中会遇到的问题 四大特征 ID相当于是人拥有的身份证&#xff0c;能够唯一确定出一个人 用户特征 主要指的是用户ID和用户画像 物品特征 主要是指物品ID和物品画像以及物品持有人。 统计特征 统计特征既包括对…
阅读更多...
miniReact＜一＞

miniReact＜一＞

一、工程化配置 1.1 目录结构 1.1.1 Multi-repo VS Mono-repo Multi-repo 每个库有自己独立的仓库&#xff0c;逻辑清晰&#xff0c;协同管理复杂 Mono-repo 很方便管理不同独立的库的生命周期&#xff0c;会有更高的操作复杂度 项目有很多包&#xff0c;同时管理多个不同的…
阅读更多...
Android Compose 使用 SVG 作为图标

Android Compose 使用 SVG 作为图标

Android Compose 使用 SVG 作为图标 依赖 val coilVersion "2.5.0"dependencies {// ...implementation("io.coil-kt:coil-compose:$coilVersion")implementation("io.coil-kt:coil-svg:$coilVersion") }工具类 package com.example.mapdraw…
阅读更多...
数据可视化工具之选，三选一？

数据可视化工具之选，三选一？

在数据可视化的世界中&#xff0c;选择一款合适的工具对于提升工作效率和洞察力至关重要。本文将对三款主流数据可视化工具进行详细比较&#xff0c;包括山海鲸可视化、Echarts和D3.js&#xff0c;以帮助您做出明智的选择。 山海鲸可视化 山海鲸可视化是一款免费且功能强大的…
阅读更多...
深入理解Django与Redis的集成实践

深入理解Django与Redis的集成实践

在现代的Web开发中&#xff0c;高效的数据存取和缓存策略是提升应用性能的关键。Django作为一个广泛使用的Python Web框架&#xff0c;提供了丰富的功能以支持高效的Web应用开发。而Redis&#xff0c;作为一个高性能的键值存储系统&#xff0c;常被用于缓存、会话管理等多种场景…
阅读更多...
Kafka 生产者缓存

Kafka 生产者缓存

不建议使用&#xff1a; public void produce(String message) {DmsProducer<String, String> producer new DmsProducer<String, String>();try {producer.produce("test1",0, "key", message);} finally {producer.close();} }原因&#x…
阅读更多...
【开源】基于JAVA+Vue+SpringBoot的康复中心管理系统

【开源】基于JAVA+Vue+SpringBoot的康复中心管理系统

目录 一、摘要1.1 项目介绍1.2 项目录屏 二、功能模块2.1 普通用户模块2.2 护工模块2.3 管理员模块 三、系统展示四、核心代码4.1 查询康复护理4.2 新增康复训练4.3 查询房间4.4 查询来访4.5 新增用药 五、免责说明 一、摘要 1.1 项目介绍 基于JAVAVueSpringBootMySQL的康复中…
阅读更多...
【Leetcode】2808. 使循环数组所有元素相等的最少秒数

【Leetcode】2808. 使循环数组所有元素相等的最少秒数

文章目录 题目思路代码结果 题目 题目链接 给你一个下标从 0 开始长度为 n 的数组 nums 。 每一秒&#xff0c;你可以对数组执行以下操作&#xff1a; 对于范围在 [0, n - 1] 内的每一个下标 i &#xff0c;将 nums[i] 替换成 nums[i] &#xff0c;nums[(i - 1 n) % n] 或者…
阅读更多...
汤姆·齐格弗里德《纳什均衡与博弈论》笔记（7）博弈论与概率论

汤姆·齐格弗里德《纳什均衡与博弈论》笔记（7）博弈论与概率论

第十一章 帕斯卡的赌注——博弈、概率、信息与无知 在与费马就这个问题的通信过程中&#xff0c;帕斯卡创造出了概率论。另外&#xff0c;帕斯卡在进行严谨的宗教反思中&#xff0c;得出了概率这个概念&#xff0c;它在此几百年后&#xff0c;成为一个关键的、对博弈论的提出有…
阅读更多...
QT仪表盘小工具

QT仪表盘小工具

头文件： /**************************************************************************** ** ** Copyright (C) 2016 The Qt Company Ltd. ** Contact: https://www.qt.io/licensing/ ** ** This file is part of the examples of the Qt Toolkit. ** ** $QT_BEGIN_LICENSE…
阅读更多...
单细胞转录组数据分析的10大软件/流程

单细胞转录组数据分析的10大软件/流程

单细胞数据分析现在已经有上千个软件工具可供使用了&#xff0c;这为用户带来便利的同时也造成了选择困难。就像时间一样&#xff0c;一个表&#xff0c;没问题&#xff0c;但如果有两个表&#xff0c;时间还不一样&#xff0c;该信谁的呢&#xff1f; 正好我们前面一篇文章介绍…
阅读更多...
LRU 缓存置换策略：提升系统效率的秘密武器(上)

LRU 缓存置换策略：提升系统效率的秘密武器(上)

&#x1f90d; 前端开发工程师、技术日更博主、已过CET6 &#x1f368; 阿珊和她的猫_CSDN博客专家、23年度博客之星前端领域TOP1 &#x1f560; 牛客高级专题作者、打造专栏《前端面试必备》 、《2024面试高频手撕题》 &#x1f35a; 蓝桥云课签约作者、上架课程《Vue.js 和 E…
阅读更多...
坚持刷题 ｜ 完全二叉树的节点个数

坚持刷题 ｜ 完全二叉树的节点个数

Hello&#xff0c;大家好&#xff0c;我是阿月&#xff01;坚持刷题&#xff0c;老年痴呆追不上我&#xff0c;今天刷&#xff1a;完全二叉树的节点个数 题目 222.完全二叉树的节点个数 代码实现 class TreeNode {int val;TreeNode left, right;public TreeNode(int val) …
阅读更多...
我用Java语言写了一个贪心算法小案例

我用Java语言写了一个贪心算法小案例

贪心算法是一种在每一步选择中都采取在当前状态下最好或最优&#xff08;即最有利&#xff09;的选择&#xff0c;从而希望导致结果是最好或最优的算法。贪心算法在有最优子结构的问题中尤为有效。最优子结构的意思是局部最优解能决定全局最优解。 下面是一个使用Java实现的贪…
阅读更多...
LeetCode765. Couples Holding Hands——并查集

LeetCode765. Couples Holding Hands——并查集

文章目录 一、题目二、题解 一、题目 There are n couples sitting in 2n seats arranged in a row and want to hold hands. The people and seats are represented by an integer array row where row[i] is the ID of the person sitting in the ith seat. The couples ar…
阅读更多...
springboot141夕阳红公寓管理系统的设计与实现

springboot141夕阳红公寓管理系统的设计与实现

基于Spring Boot的夕阳红公寓管理系统的设计与实现 摘 要 如今社会上各行各业&#xff0c;都在用属于自己专用的软件来进行工作&#xff0c;互联网发展到这个时候&#xff0c;人们已经发现离不开了互联网。互联网的发展&#xff0c;离不开一些新的技术&#xff0c;而新技术的…
阅读更多...
Lua脚本

Lua脚本

1.准备 1.简介 1.Lua是一种轻量小巧的脚本语言&#xff0c;用标准C语言编写并以源代码形式开放 2.目标 1.其设计目的是为了嵌入应用程序中&#xff0c;从而为应用程序提供灵活的扩展和定制功能 3.特点 1.轻量级&#xff1a;用标准C语言编写并以源代码形式开放&#xff0c;编译后…
阅读更多...
【Qt】—— Qt Creator界⾯认识

【Qt】—— Qt Creator界⾯认识

目录 &#xff08;一&#xff09;左边栏 &#xff08;二&#xff09;代码编辑区 &#xff08;三&#xff09;UI设计界⾯ &#xff08;四&#xff09;构建区 &#xff08;一&#xff09;左边栏 在编辑模式下&#xff0c;左边竖排的两个窗⼝叫做"边栏"。 ①是项⽬…
阅读更多...
最新文章

Copyright @ 2022~2023