【全志V3s】SPI NAND Flash 驱动开发

文章目录

  • 一、硬件介绍
    • V3s的启动顺序
  • 二、驱动支持
    • U-Boot驱动
    • 主线 Linux 驱动已经支持
  • 三、烧录工具 xfel
  • 四、构建U-Boot(官方的Uboot)
    • 先编译一下
    • 开始spi nand flash 代码层面的适配
    • 修改menuconfig配置
      • ARM architecture配置Support for SPI Nand Flash on Allwinner SoCs in SPL
      • Boot options 取消 Enable boot arguments
      • 打开Device Drivers下面的SPI Support
      • 在Device Drivers下面 MTD Support 中勾选 Enable MTD layer Driver Model for MTD driver
      • 在Command line interface的Device access commands勾选 mtd,这样后续生成的uboot中才会有MTD相关的命令,类似于SPI NOR Flash添加的sf命令
      • Environment 取消勾选 Environment is in SPI flash,这个选项是在打开SPI Support之后才会被看到
    • 修改uboot输出文件使其可以在spinandflash上运行
  • 五、构建Linux Kernel
    • 修改设备树
      • 修改 chosen
      • 增加SPI0节点
    • menuconfig里面配置增加驱动支持
      • Memory Technology Device (MTD) support 勾选 SPI NAND device Support 和 Enable UBI - Unsorted block image![在这里插入图片描述](https://img-blog.csdnimg.cn/a156167e31c44ac7b92b7edb5ba912c3.png)
      • File Systems的Miscellaneous filesystems中勾选UBIFS file system support, 这一步需要刚才的Enable UBI打开之后才能看到
    • 编译Linux Kernel
    • 烧录 Linux Kernel
  • 六、构建文件系统
  • 七、进入文件系统后的操作
    • 查看挂载的文件系统
    • 查看分区
    • 查看存储
    • 查看Linux内核启动参数
    • 查看目录信息
  • 八、总结
  • 九、打包
  • 十、工程源码
    • 原始的文件:
    • 配置好的文件:

芯片:W25N01GVZEIG

一、硬件介绍

datasheet上的描述:
在这里插入图片描述

  • SLC工艺
  • 2KB*65536页
  • 10万次擦写次数

在这里插入图片描述
焊好以后用CH341A读了一下
在这里插入图片描述

V3s的启动顺序

在这里插入图片描述
上面这张图描述了soc启动的四个顺序,分别是usb启动、sd卡启动、spi norflash启动、spi nandflash启动四种方式。前面的测试中一直走的是sd卡启动,但是从成本和稳定性上说,spi nandflash其实是最合适的。

sd 卡需要卡座拔插,在震动环境下不稳定,容易接触不良,容量大,其实也贵,相当于EMMC。
spi nor flash容量一般在16MB左右,也有32MB和64MB的,但是价格较贵。
2023年9月16日15:36:26,在某宝上数据对比一下

容量接口型号价格
16MBspi nor flashW25Q128JVSIM3.8¥
32MBspi nor flashW25Q256JVEIQ7.1¥
128MBspi nand flashW25N01GVZEIG4.0¥
256MBspi nand flashW25N02KVZEIR5.9¥

所以,16M/32M 的spi nor flash 真的没有什么优势。做非常简单的应用还可以,其他就算了吧。故以后自己玩也要玩nand flash吧,nor flash没有什么应用场景。

有兴趣可以看看,我之前的记录:

全志V3s学习记录:Nor Flash使用(一)

全志V3s学习记录:Nor Flash使用(二)

二、驱动支持

U-Boot驱动

使用:http://sources.buildroot.net/uboot/u-boot-2022.04.tar.bz2
在这里插入图片描述

主线 Linux 驱动已经支持

4.19 及其以后的版本支持 spi nand
https://github.com/torvalds/linux/blob/v4.19/drivers/mtd/nand/spi/winbond.c

目前主线Linux已经支持winbond:W25N01GVZEIG,如下:

在线Linux Kernel代码:https://elixir.bootlin.com/linux/v5.2.20/source/drivers/mtd/nand/spi/winbond.c

在这里插入图片描述

static const struct spinand_info winbond_spinand_table[] = {SPINAND_INFO("W25M02GV", 0xAB,NAND_MEMORG(1, 2048, 64, 64, 1024, 20, 1, 1, 2),NAND_ECCREQ(1, 512),SPINAND_INFO_OP_VARIANTS(&read_cache_variants,&write_cache_variants,&update_cache_variants),0,SPINAND_ECCINFO(&w25m02gv_ooblayout, NULL),SPINAND_SELECT_TARGET(w25m02gv_select_target)),SPINAND_INFO("W25N01GV", 0xAA,NAND_MEMORG(1, 2048, 64, 64, 1024, 20, 1, 1, 1),NAND_ECCREQ(1, 512),SPINAND_INFO_OP_VARIANTS(&read_cache_variants,&write_cache_variants,&update_cache_variants),0,SPINAND_ECCINFO(&w25m02gv_ooblayout, NULL)),
};

三、烧录工具 xfel

之前烧录spi nor flash的时候,使用的是sunxi-fel工具,如果需要烧录spi nand flash image,就需要xfel

https://github.com/xboot/xfel

或者 git https://github.com/xboot/xfel.git

下载直接选main,解压、直接make就可以了。

  • 解压
  • make
  • sudo make install

需要安装sudo apt-get install libusb-1.0-0-dev libusb-dev libudev-dev

usage:xfel version                                        - Show chip versionxfel hexdump <address> <length>                     - Dumps memory region in hexxfel dump <address> <length>                        - Binary memory dump to stdoutxfel read32 <address>                               - Read 32-bits value from device memoryxfel write32 <address> <value>                      - Write 32-bits value to device memoryxfel read <address> <length> <file>                 - Read memory to filexfel write <address> <file>                         - Write file to memoryxfel exec <address>                                 - Call function addressxfel reset                                          - Reset device using watchdogxfel sid                                            - Show sid informationxfel jtag                                           - Enable jtag debugxfel ddr [type]                                     - Initial ddr controller with optional typexfel sign <public-key> <private-key> <file>         - Generate ecdsa256 signature file for sha256 of sidxfel spinor                                         - Detect spi nor flashxfel spinor erase <address> <length>                - Erase spi nor flashxfel spinor read <address> <length> <file>          - Read spi nor flash to filexfel spinor write <address> <file>                  - Write file to spi nor flashxfel spinand                                        - Detect spi nand flashxfel spinand erase <address> <length>               - Erase spi nand flashxfel spinand read <address> <length> <file>         - Read spi nand flash to filexfel spinand write <address> <file>                 - Write file to spi nand flashxfel spinand splwrite <split-size> <address> <file> - Write file to spi nand flash with split supportxfel extra [...]                                    - The extra commands
liefyuan@ubuntu:~$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 010: ID 048d:5702 Integrated Technology Express, Inc. 
Bus 002 Device 009: ID 1f3a:efe8 Onda (unverified) V972 tablet in flashing mode
Bus 002 Device 003: ID 0e0f:0002 VMware, Inc. Virtual USB Hub
Bus 002 Device 002: ID 0e0f:0003 VMware, Inc. Virtual Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 002 Device 009: ID 1f3a:efe8 Onda (unverified) V972 tablet in flashing mode

liefyuan@ubuntu:~$ xfel version
AWUSBFEX ID=0x00168100(V3S/S3) dflag=0x44 dlength=0x08 scratchpad=0x00007e00

这就是ubuntu识别出来进入USB升级模式的V3s了。

简单使用一下:

liefyuan@ubuntu:~$ xfel spinand
Found spi nand flash 'W25N01GV' with 134217728 bytes
liefyuan@ubuntu:~$ xfel version
AWUSBFEX ID=0x00168100(V3S/S3) dflag=0x44 dlength=0x08 scratchpad=0x00007e00
liefyuan@ubuntu:~$ sudo xfel spinand erase 0x0 0x100000
[sudo] password for liefyuan: 12% [======                                          ] 4.334 MB/s, ETA 00:00    25% [============                                    ] 4.334 MB/s, ETA 00:00    38% [==================                              ] 4.377 MB/s, ETA 00:00    50% [========================                        ] 4.363 MB/s, ETA 00:00    62% [==============================                  ] 4.386 MB/s, ETA 00:00    75% [====================================            ] 4.348 MB/s, ETA 00:00    88% [==========================================      ] 4.392 MB/s, ETA 00:00   100% [================================================] 1024.000 KB, 4.382 MB/s        

四、构建U-Boot(官方的Uboot)

地址:http://sources.buildroot.net/uboot/u-boot-2022.04.tar.bz2

驱动是支持的:

liefyuan@ubuntu:~/V3s/u-boot-2022.04$ find ./ -name "winbond.c"
./drivers/mtd/nand/spi/winbond.c

先编译一下

先编译一下看看有没有什么问题

make ARCH=arm LicheePi_Zero_defconfig
make ARCH=arm menuconfig
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf-

最后一步报错了,交叉编译器版本太老了。

*** Your GCC is older than 6.0 and is not supported
arch/arm/config.mk:74: recipe for target 'checkgcc6' failed
make: *** [checkgcc6] Error 1

换个高版本的交叉编译器!
再装个软件:sudo apt install swig

初步编译成功了!

开始spi nand flash 代码层面的适配

拷贝spl_spinand_sunxi.c到arch/arm/mach-sunxi目录下,文件地址:

https://github.com/bamkrs/openwrt/blob/dolphinpi-spinand/package/boot/uboot-sunxi/src/arch/arm/mach-sunxi/spl_spinand_sunxi.c

spl_spinand_sunxi.c需要做一些修改:

  • 添加头文件
  • 添加函数调用参数
// add by liefyuan
#include <image.h>
#include <linux/delay.h>ret = spl_parse_image_header(spl_image, bootdev, header); // modified by liefyuan

然后在,arch/arm/mach-sunxi/Kconfig 文件中添加内容:

config SPL_SPINAND_SUNXIbool "Support for SPI Nand Flash on Allwinner SoCs in SPL"depends on MACH_SUN8I_V3ShelpEnable support for SPI Nand Flash. This option allows SPL to read fromsunxi SPI Nand Flash. It uses the same method as the boot ROM, so doesnot need any extra configuration.

1043gg 处添加吧

然后在 arch/arm/mach-sunxi/Makefile添加 spl_spinand_sunxi.c的编译选项

ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_MACH_SUNIV)	+= dram_suniv.o
obj-$(CONFIG_DRAM_SUN4I)	+= dram_sun4i.o
obj-$(CONFIG_DRAM_SUN6I)	+= dram_sun6i.o
obj-$(CONFIG_DRAM_SUN8I_A23)	+= dram_sun8i_a23.o
obj-$(CONFIG_DRAM_SUN8I_A33)	+= dram_sun8i_a33.o
obj-$(CONFIG_DRAM_SUN8I_A83T)	+= dram_sun8i_a83t.o
obj-$(CONFIG_DRAM_SUN9I)	+= dram_sun9i.o
obj-$(CONFIG_SPL_SPI_SUNXI)	+= spl_spi_sunxi.o
obj-$(CONFIG_SUNXI_DRAM_DW)	+= dram_sunxi_dw.o
obj-$(CONFIG_SUNXI_DRAM_DW)	+= dram_timings/
obj-$(CONFIG_DRAM_SUN50I_H6)	+= dram_sun50i_h6.o
obj-$(CONFIG_DRAM_SUN50I_H6)	+= dram_timings/
obj-$(CONFIG_DRAM_SUN50I_H616)	+= dram_sun50i_h616.o
obj-$(CONFIG_DRAM_SUN50I_H616)	+= dram_timings/
obj-$(CONFIG_SPL_SPINAND_SUNXI)    += spl_spinand_sunxi.o
endif

继续,在 arch/arm/dts/sun8i-v3s-licheepi-zero.dts文件中添加spi0的内容:

&spi0 {pinctrl-0 = <&spi0_pins>;pinctrl-names = "default";status = "okay";flash@0 {#address-cells = <1>;#size-cells = <1>;compatible = "spi-nand";reg = <0>;spi-max-frequency = <50000000>;};
};

最后,在 include/configs/sun8i.h添加内容,要在#include <configs/sunxi-common.h>之前添加。

#ifdef CONFIG_BOOTCOMMAND
#undef CONFIG_BOOTCOMMAND
#endif#ifdef COFNIG_BOOTARGS
#undef CONFIG_BOOTARGS
#endif#define CONFIG_BOOTCOMMAND  "mtd read spi-nand0 0x41800000 0x100000 0x20000; "  \"mtd read spi-nand0 0x41000000 0x120000 0x500000; " \"bootz 0x41000000 - 0x41800000"#define CONFIG_BOOTARGS    "console=ttyS0,115200 earlyprintk panic=5 rootwait " \"mtdparts=spi0.0:1M(uboot)ro,128k(dtb)ro,5M(kernel)ro,-(rootfs) ubi.mtd=3 root=ubi0:rootfs rw rootfstype=ubifs"

修改menuconfig配置

命令:make ARCH=arm menuconfig

ARM architecture配置Support for SPI Nand Flash on Allwinner SoCs in SPL

在这里插入图片描述

Boot options 取消 Enable boot arguments

在这里插入图片描述

打开Device Drivers下面的SPI Support

在这里插入图片描述

在Device Drivers下面 MTD Support 中勾选 Enable MTD layer Driver Model for MTD driver

在这里插入图片描述

在Command line interface的Device access commands勾选 mtd,这样后续生成的uboot中才会有MTD相关的命令,类似于SPI NOR Flash添加的sf命令

在这里插入图片描述

Environment 取消勾选 Environment is in SPI flash,这个选项是在打开SPI Support之后才会被看到

在这里插入图片描述OK,更改完毕。

再次编译一下就OK了。

make ARCH=arm LicheePi_Zero_defconfig
make ARCH=arm menuconfig
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf-

修改uboot输出文件使其可以在spinandflash上运行

此时,u-boot-sunxi-with-spl.bin还不能被直接下载到nand flash。因为V3s默认从spi nand flash加载page内容,是1个page加载1KB。我使用的是winbond的W25N01GVZEIG,它的page是2KB。

脚本地址:https://github.com/bamkrs/openwrt/blob/dolphinpi-spinand/target/linux/sunxi/image/gen_sunxi_spinand_onlyboot_img.sh

运行命令:

./gen_sunxi_spinand_onlyboot_img.sh split.bin u-boot-sunxi-with-spl.bin 2048 128

其中split.bin代表生成的目标文件,u-boot-sunxi-with-spl.bin表示刚刚编译好的uboot文件,2048代表page大小,单位是byte,而128则代表block大小,单位是k byte。

下载修改后的uboot文件到spinandflash文件

liefyuan@ubuntu:~/V3s/u-boot-3s-spi-experimental$ sudo xfel spinand erase 0x0 0x100000
[sudo] password for liefyuan: 
100% [================================================] 1024.000 KB, 4.381 MB/s        
liefyuan@ubuntu:~/V3s/u-boot-3s-spi-experimental$ sudo xfel spinand write 0x0 split.bin
100% [================================================] 505.250 KB, 91.550 KB/s        

写入文件是nandflash的由0开始的地址空间。

上电:


U-Boot SPL 2022.04 (Sep 17 2023 - 22:00:15 +0800)
DRAM: 64 MiB
Trying to boot from sunxi SPI-NAND
sunxi SPI-NAND: Found Winbond W25N01GVxxIG (efaa21)
sunxi SPI-NAND: Loading u-boot from 0x20000
sunxi SPI-NAND: u-boot hcrc OK!U-Boot 2022.04 (Sep 17 2023 - 22:00:15 +0800) Allwinner TechnologyCPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
Core:  23 devices, 11 uclasses, devicetree: separate
WDT:   Not starting watchdog@1c20ca0
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... Card did not respond to voltage select! : -110
In:    serial@1c28000
Out:   serial@1c28000
Err:   serial@1c28000
Net:   No ethernet found.
Hit any key to stop autoboot:  0
Reading 131072 byte(s) (64 page(s)) at offset 0x00100000
Reading 5242880 byte(s) (2560 page(s)) at offset 0x00120000
zimage: Bad magic!
=>

五、构建Linux Kernel

源码:https://github.com/Lichee-Pi/linux/tree/zero-5.2.y

修改设备树

修改 chosen

chosen {bootargs = "console=ttyS0,115200 earlyprintk panic=5 rootwait mtdparts=spi0.0:1M(uboot)ro,128k(dtb)ro,5M(kernel)ro,-(rootfs) ubi.mtd=3 root=ubi0:rootfs rw rootfstype=ubifs";};

增加SPI0节点

文件地址:linux-zero-5.2.y/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts

&spi0 {status ="okay";spi_nand: spi_nand@0 {#address-cells = <1>;#size-cells = <1>;compatible = "spi-nand";reg = <0>;spi-max-frequency = <50000000>;partition@0 {label = "uboot";reg = <0x0 0x100000>;read-only;};partition@100000 {label = "dtb";reg = <0x100000 0x20000>;read-only;};partition@120000 {label = "kernel";reg = <0x120000 0x500000>;read-only;};partition@620000 {label = "rootfs";reg = <0x620000 0x79E0000>;};};
};

menuconfig里面配置增加驱动支持

命令:make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- menuconfig

Memory Technology Device (MTD) support 勾选 SPI NAND device Support 和 Enable UBI - Unsorted block image在这里插入图片描述

File Systems的Miscellaneous filesystems中勾选UBIFS file system support, 这一步需要刚才的Enable UBI打开之后才能看到

在这里插入图片描述

编译Linux Kernel

  • 清除:make clean

  • make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- licheepi_zero_defconfig

  • time make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- -j16

  • make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- dtbs

  • make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- menuconfig

烧录 Linux Kernel

sudo xfel spinand erase 0x100000 0x20000
sudo xfel spinand write 0x100000 sun8i-v3s-licheepi-zero-with-800x480-lcd.dtb
sudo xfel spinand erase 0x120000 0x500000
sudo xfel spinand write 0x120000 zImage

上电:


U-Boot SPL 2022.04 (Sep 17 2023 - 22:00:15 +0800)
DRAM: 64 MiB
Trying to boot from sunxi SPI-NAND
sunxi SPI-NAND: Found Winbond W25N01GVxxIG (efaa21)
sunxi SPI-NAND: Loading u-boot from 0x20000
sunxi SPI-NAND: u-boot hcrc OK!U-Boot 2022.04 (Sep 17 2023 - 22:00:15 +0800) Allwinner TechnologyCPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
Core:  23 devices, 11 uclasses, devicetree: separate
WDT:   Not starting watchdog@1c20ca0
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... Card did not respond to voltage select! : -110
In:    serial@1c28000
Out:   serial@1c28000
Err:   serial@1c28000
Net:   No ethernet found.
Hit any key to stop autoboot:  0
Reading 131072 byte(s) (64 page(s)) at offset 0x00100000
Reading 5242880 byte(s) (2560 page(s)) at offset 0x00120000
zimage: Bad magic!
=>
U-Boot SPL 2022.04 (Sep 17 2023 - 22:00:15 +0800)
DRAM: 64 MiB
Trying to boot from sunxi SPI-NAND
sunxi SPI-NAND: Found Winbond W25N01GVxxIG (efaa21)
sunxi SPI-NAND: Loading u-boot from 0x20000
sunxi SPI-NAND: u-boot hcrc OK!U-Boot 2022.04 (Sep 17 2023 - 22:00:15 +0800) Allwinner TechnologyCPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
Core:  23 devices, 11 uclasses, devicetree: separate
WDT:   Not starting watchdog@1c20ca0
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... Card did not respond to voltage select! : -110
In:    serial@1c28000
Out:   serial@1c28000
Err:   serial@1c28000
Net:   No ethernet found.
Hit any key to stop autoboot:  0
Reading 131072 byte(s) (64 page(s)) at offset 0x00100000
Reading 5242880 byte(s) (2560 page(s)) at offset 0x00120000
Kernel image @ 0x41000000 [ 0x000000 - 0x4462a8 ]
## Flattened Device Tree blob at 41800000Booting using the fdt blob at 0x41800000Loading Device Tree to 42df9000, end 42dff021 ... OKStarting kernel ...[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.2.0-licheepi-zero (liefyuan@ubuntu) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #2 SMP Sun Sep 17 22:22:36 HKT 2023
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Lichee Pi Zero
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: Using PSCI v0.1 Function IDs from DT
[    0.000000] percpu: Embedded 16 pages/cpu s34508 r8192 d22836 u65536
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk panic=5 rootwait mtdparts=spi0.0:1M(uboot)ro,128k(dtb)ro,5M(kernel)ro,-(rootfs) ubi.mtd=3 root=ubi0:rootfs rw rootfstype=ubifs
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 54004K/65536K available (7168K kernel code, 309K rwdata, 1748K rodata, 1024K init, 257K bss, 11532K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
[    0.000000] random: get_random_bytes called from start_kernel+0x300/0x48c with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000020] Switching to timer-based delay loop, resolution 41ns
[    0.000207] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000453] Console: colour dummy device 80x30
[    0.000509] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000524] pid_max: default: 32768 minimum: 301
[    0.000684] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000699] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001494] CPU: Testing write buffer coherency: ok
[    0.001994] /cpus/cpu@0 missing clock-frequency property
[    0.002020] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002813] Setting up static identity map for 0x40100000 - 0x40100060
[    0.003023] rcu: Hierarchical SRCU implementation.
[    0.003573] smp: Bringing up secondary CPUs ...
[    0.003593] smp: Brought up 1 node, 1 CPU
[    0.003602] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.003609] CPU: All CPU(s) started in HYP mode.
[    0.003614] CPU: Virtualization extensions available.
[    0.004673] devtmpfs: initialized
[    0.008316] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.008615] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.008646] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.008884] pinctrl core: initialized pinctrl subsystem
[    0.010035] NET: Registered protocol family 16
[    0.010553] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.011815] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.011835] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.039592] SCSI subsystem initialized
[    0.039760] usbcore: registered new interface driver usbfs
[    0.039851] usbcore: registered new interface driver hub
[    0.039964] usbcore: registered new device driver usb
[    0.040374] mc: Linux media interface: v0.10
[    0.040435] videodev: Linux video capture interface: v2.00
[    0.040647] Advanced Linux Sound Architecture Driver Initialized.
[    0.042457] clocksource: Switched to clocksource arch_sys_counter
[    0.054799] NET: Registered protocol family 2
[    0.055598] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.055636] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.055662] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.055687] TCP: Hash tables configured (established 1024 bind 1024)
[    0.055836] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.055887] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.056173] NET: Registered protocol family 1
[    0.058034] Initialise system trusted keyrings
[    0.058413] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.095330] Key type asymmetric registered
[    0.095353] Asymmetric key parser 'x509' registered
[    0.095451] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.095463] io scheduler mq-deadline registered
[    0.095469] io scheduler kyber registered
[    0.096519] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
[    0.100286] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.100703] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator
[    0.101422] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.207095] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.210551] printk: console [ttyS0] disabled
[    0.230855] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 34, base_baud = 1500000) is a U6_16550A
[    0.776897] printk: console [ttyS0] enabled
[    0.782886] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pe not found, using dummy regulator
[    0.816159] panel-simple panel: panel supply power not found, using dummy regulator
[    0.825484] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pc not found, using dummy regulator
[    0.837018] spi-nand spi0.0: Winbond SPI NAND was found.
[    0.842346] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[    0.851243] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.857692] Creating 4 MTD partitions on "spi0.0":
[    0.862530] 0x000000000000-0x000000100000 : "uboot"
[    0.870375] 0x000000100000-0x000000120000 : "dtb"
[    0.876231] 0x000000120000-0x000000620000 : "kernel"
[    0.882331] random: fast init done
[    0.895871] 0x000000620000-0x000008000000 : "rootfs"
[    1.066735] random: crng init done
[    1.153103] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.159637] ehci-platform: EHCI generic platform driver
[    1.165246] ehci-platform 1c1a000.usb: EHCI Host Controller
[    1.170857] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[    1.178853] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000
[    1.212460] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    1.219633] hub 1-0:1.0: USB hub found
[    1.223604] hub 1-0:1.0: 1 port detected
[    1.228232] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.234555] ohci-platform: OHCI generic platform driver
[    1.240097] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    1.246819] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    1.254782] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400
[    1.327507] hub 2-0:1.0: USB hub found
[    1.331344] hub 2-0:1.0: 1 port detected
[    1.338664] usbcore: registered new interface driver usb-storage
[    1.346267] sun6i-rtc 1c20400.rtc: registered as rtc0
[    1.351329] sun6i-rtc 1c20400.rtc: RTC enabled
[    1.356070] i2c /dev entries driver
[    1.360924] input: ns2009_ts as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0048/input/input0
[    1.370612] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.379328] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pf not found, using dummy regulator
[    1.415092] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[    1.422648] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pg not found, using dummy regulator
[    1.434001] usbcore: registered new interface driver usbhid
[    1.439580] usbhid: USB HID core driver
[    1.446187] Initializing XFRM netlink socket
[    1.450498] NET: Registered protocol family 17
[    1.455640] Registering SWP/SWPB emulation handler
[    1.461540] Loading compiled-in X.509 certificates
[    1.475480] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pe not found, using dummy regulator
[    1.488036] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0848700)
[    1.495606] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc08459fc)
[    1.503340] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.509947] [drm] No driver support for vblank timestamp query.
[    1.516932] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[    1.577191] Console: switching to colour frame buffer device 100x30
[    1.605681] sun4i-drm display-engine: fb0: sun4i-drmdrmfb frame buffer device
[    1.613678] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[    1.625209] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    1.630975] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[    1.640115] hub 3-0:1.0: USB hub found
[    1.644084] hub 3-0:1.0: 1 port detected
[    1.649367] ubi0: attaching mtd3
[    2.218438] ubi0: scanning is finished
[    2.222200] ubi0: empty MTD device detected
[    2.255116] ubi0: attached mtd3 (name "rootfs", size 121 MiB)
[    2.260921] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.267867] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.274665] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.281615] ubi0: good PEBs: 975, bad PEBs: 0, corrupted PEBs: 0
[    2.287644] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[    2.294873] ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 2177542106
[    2.304004] ubi0: available PEBs: 951, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20
[    2.313392] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01T00:34:30 UTC (2070)
[    2.321843] vcc3v0: disabling
[    2.324878] vcc3v3: disabling
[    2.327871] vcc5v0: disabling
[    2.330836] ALSA device list:
[    2.333827]   No soundcards found.
[    2.337799] ubi0: background thread "ubi_bgt0d" started, PID 93
[    2.349302] VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0): error -19
[    2.357403] Please append a correct "root=" boot option; here are the available partitions:
[    2.365795] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    2.374055] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.0-licheepi-zero #2
[    2.381091] Hardware name: Allwinner sun8i Family
[    2.385824] [<c010ed14>] (unwind_backtrace) from [<c010b72c>] (show_stack+0x10/0x14)
[    2.393566] [<c010b72c>] (show_stack) from [<c071a650>] (dump_stack+0x84/0x98)
[    2.400788] [<c071a650>] (dump_stack) from [<c011dddc>] (panic+0x110/0x2fc)
[    2.407750] [<c011dddc>] (panic) from [<c0a01358>] (mount_block_root+0x214/0x2f0)
[    2.415229] [<c0a01358>] (mount_block_root) from [<c0a01558>] (prepare_namespace+0x9c/0x194)
[    2.423660] [<c0a01558>] (prepare_namespace) from [<c0732aa4>] (kernel_init+0x8/0x10c)
[    2.431570] [<c0732aa4>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[    2.439128] Exception stack(0xc3833fb0 to 0xc3833ff8)
[    2.444175] 3fa0:                                     00000000 00000000 00000000 00000000
[    2.452343] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.460508] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    2.467127] Rebooting in 5 seconds..

很好,上电成功了!

六、构建文件系统

现成的文件系统:
链接:https://pan.baidu.com/s/1-HMjT5BCYq0aImIJcQyJlw
提取码:lief
–来自百度网盘超级会员V5的分享

系统名是:root
无密码

spi nand flash 一般使用的文件系统是ubifs文件系统。涉及到两个工具
第一步:先用mkfs.ubifs生成rootfs_ubifs.img文件,其中-d target就是根文件目录的位置:

sudo mkfs.ubifs -x lzo -F -m 2048 -e 126976 -c 732 -o rootfs_ubifs.img -d target

第二步:用ubinize生成最终的ubi.img

sudo ubinize -o ubi.img -m 2048 -p 131072 -O 2048 -s 2048 ./ubinize.cfg  -v

ubinize.cfg文件

[rootfs-volume]
mode=ubi
image=rootfs_ubifs.img
vol_id=0
vol_size=92946432
vol_type=dynamic
vol_name=rootfs
vol_flags=autoresize
vol_alignment=1

有了ubi.img之后,就可以使用xfel工具烧录了。

sudo xfel spinand erase 0x620000 0x79DFFFF
sudo xfel spinand write 0x620000 ubi.img 

烧录成功后,上电信息:

U-Boot SPL 2022.04 (Sep 17 2023 - 22:00:15 +0800)
DRAM: 64 MiB
Trying to boot from sunxi SPI-NAND
sunxi SPI-NAND: Found Winbond W25N01GVxxIG (efaa21)
sunxi SPI-NAND: Loading u-boot from 0x20000
sunxi SPI-NAND: u-boot hcrc OK!U-Boot 2022.04 (Sep 17 2023 - 22:00:15 +0800) Allwinner TechnologyCPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
Core:  23 devices, 11 uclasses, devicetree: separate
WDT:   Not starting watchdog@1c20ca0
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... Card did not respond to voltage select! : -110
In:    serial@1c28000
Out:   serial@1c28000
Err:   serial@1c28000
Net:   No ethernet found.
Hit any key to stop autoboot:  0
Reading 131072 byte(s) (64 page(s)) at offset 0x00100000
Reading 5242880 byte(s) (2560 page(s)) at offset 0x00120000
Kernel image @ 0x41000000 [ 0x000000 - 0x4462a8 ]
## Flattened Device Tree blob at 41800000Booting using the fdt blob at 0x41800000Loading Device Tree to 42df9000, end 42dff021 ... OKStarting kernel ...[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.2.0-licheepi-zero (liefyuan@ubuntu) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #2 SMP Sun Sep 17 22:22:36 HKT 2023
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Lichee Pi Zero
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: Using PSCI v0.1 Function IDs from DT
[    0.000000] percpu: Embedded 16 pages/cpu s34508 r8192 d22836 u65536
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk panic=5 rootwait mtdparts=spi0.0:1M(uboot)ro,128k(dtb)ro,5M(kernel)ro,-(rootfs) ubi.mtd=3 root=ubi0:rootfs rw rootfstype=ubifs
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 54004K/65536K available (7168K kernel code, 309K rwdata, 1748K rodata, 1024K init, 257K bss, 11532K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
[    0.000000] random: get_random_bytes called from start_kernel+0x300/0x48c with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000021] Switching to timer-based delay loop, resolution 41ns
[    0.000203] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000445] Console: colour dummy device 80x30
[    0.000501] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000518] pid_max: default: 32768 minimum: 301
[    0.000678] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000695] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001498] CPU: Testing write buffer coherency: ok
[    0.002002] /cpus/cpu@0 missing clock-frequency property
[    0.002028] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002792] Setting up static identity map for 0x40100000 - 0x40100060
[    0.003005] rcu: Hierarchical SRCU implementation.
[    0.003552] smp: Bringing up secondary CPUs ...
[    0.003574] smp: Brought up 1 node, 1 CPU
[    0.003584] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.003590] CPU: All CPU(s) started in HYP mode.
[    0.003595] CPU: Virtualization extensions available.
[    0.004666] devtmpfs: initialized
[    0.008313] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.008616] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.008647] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.008888] pinctrl core: initialized pinctrl subsystem
[    0.010027] NET: Registered protocol family 16
[    0.010546] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.011810] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.011827] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.039494] SCSI subsystem initialized
[    0.039663] usbcore: registered new interface driver usbfs
[    0.039754] usbcore: registered new interface driver hub
[    0.039863] usbcore: registered new device driver usb
[    0.040242] mc: Linux media interface: v0.10
[    0.040330] videodev: Linux video capture interface: v2.00
[    0.040556] Advanced Linux Sound Architecture Driver Initialized.
[    0.042370] clocksource: Switched to clocksource arch_sys_counter
[    0.054726] NET: Registered protocol family 2
[    0.055518] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.055555] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.055584] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.055607] TCP: Hash tables configured (established 1024 bind 1024)
[    0.055753] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.055807] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.056106] NET: Registered protocol family 1
[    0.057942] Initialise system trusted keyrings
[    0.058328] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.095103] Key type asymmetric registered
[    0.095125] Asymmetric key parser 'x509' registered
[    0.095222] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.095235] io scheduler mq-deadline registered
[    0.095242] io scheduler kyber registered
[    0.096292] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
[    0.100066] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.100482] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator
[    0.101204] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.206901] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.210326] printk: console [ttyS0] disabled
[    0.230632] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 34, base_baud = 1500000) is a U6_16550A
[    0.776672] printk: console [ttyS0] enabled
[    0.782652] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pe not found, using dummy regulator
[    0.815920] panel-simple panel: panel supply power not found, using dummy regulator
[    0.825241] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pc not found, using dummy regulator
[    0.836785] spi-nand spi0.0: Winbond SPI NAND was found.
[    0.842113] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[    0.851018] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.857466] Creating 4 MTD partitions on "spi0.0":
[    0.862266] 0x000000000000-0x000000100000 : "uboot"
[    0.870113] 0x000000100000-0x000000120000 : "dtb"
[    0.875974] 0x000000120000-0x000000620000 : "kernel"
[    0.882146] random: fast init done
[    0.895633] 0x000000620000-0x000008000000 : "rootfs"
[    1.066444] random: crng init done
[    1.152066] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.158675] ehci-platform: EHCI generic platform driver
[    1.164241] ehci-platform 1c1a000.usb: EHCI Host Controller
[    1.169848] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[    1.177848] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000
[    1.212377] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    1.219546] hub 1-0:1.0: USB hub found
[    1.223520] hub 1-0:1.0: 1 port detected
[    1.228140] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.234467] ohci-platform: OHCI generic platform driver
[    1.240007] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    1.246726] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    1.254694] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400
[    1.327423] hub 2-0:1.0: USB hub found
[    1.331262] hub 2-0:1.0: 1 port detected
[    1.338553] usbcore: registered new interface driver usb-storage
[    1.346152] sun6i-rtc 1c20400.rtc: registered as rtc0
[    1.351212] sun6i-rtc 1c20400.rtc: RTC enabled
[    1.355953] i2c /dev entries driver
[    1.360813] input: ns2009_ts as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0048/input/input0
[    1.370500] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.379224] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pf not found, using dummy regulator
[    1.415004] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[    1.422572] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pg not found, using dummy regulator
[    1.433929] usbcore: registered new interface driver usbhid
[    1.439505] usbhid: USB HID core driver
[    1.446113] Initializing XFRM netlink socket
[    1.450423] NET: Registered protocol family 17
[    1.455540] Registering SWP/SWPB emulation handler
[    1.461453] Loading compiled-in X.509 certificates
[    1.475387] sun8i-v3s-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pe not found, using dummy regulator
[    1.487938] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0848700)
[    1.495525] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc08459fc)
[    1.503262] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.509869] [drm] No driver support for vblank timestamp query.
[    1.516859] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[    1.577117] Console: switching to colour frame buffer device 100x30
[    1.605592] sun4i-drm display-engine: fb0: sun4i-drmdrmfb frame buffer device
[    1.613580] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[    1.625097] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    1.630863] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[    1.639991] hub 3-0:1.0: USB hub found
[    1.643951] hub 3-0:1.0: 1 port detected
[    1.649229] ubi0: attaching mtd3
[    2.236686] ubi0: scanning is finished
[    2.282072] ubi0: volume 0 ("rootfs") re-sized from 732 to 951 LEBs
[    2.289265] ubi0: attached mtd3 (name "rootfs", size 121 MiB)
[    2.295090] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.301957] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.308784] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.315757] ubi0: good PEBs: 975, bad PEBs: 0, corrupted PEBs: 0
[    2.321756] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    2.328991] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 405437201
[    2.338037] ubi0: available PEBs: 0, total reserved PEBs: 975, PEBs reserved for bad PEB handling: 20
[    2.347328] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01T00:23:16 UTC (1396)
[    2.355804] vcc3v0: disabling
[    2.358782] vcc3v3: disabling
[    2.361746] vcc5v0: disabling
[    2.364799] ALSA device list:
[    2.367768]   No soundcards found.
[    2.371779] ubi0: background thread "ubi_bgt0d" started, PID 93
[    2.388321] UBIFS (ubi0:0): Mounting in unauthenticated mode
[    2.397175] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 94
[    2.495382] UBIFS (ubi0:0): start fixing up free space
[    2.933104] UBIFS (ubi0:0): free space fixup complete
[    2.988109] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.995678] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    3.005611] UBIFS (ubi0:0): FS size: 91549696 bytes (87 MiB, 721 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    3.016060] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[    3.021893] UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 0D89ACE3-5309-484C-888D-2628D2752C10, small LPT model
[    3.045981] VFS: Mounted root (ubifs filesystem) on device 0:13.
[    3.055787] devtmpfs: mounted
[    3.061247] Freeing unused kernel memory: 1024K
[    3.067684] Run /sbin/init as init process
Starting logging: OK
Starting mdev...
/etc/init.d/S10mdev: line 21: can't create /proc/sys/kernel/hotplug: nonexistent directory
modprobe: can't change directory to '/lib/modules': No such file or directory
Initializing random number generator... done.
Starting network: OKWelcome to Lichee Pi
Lichee login:
Welcome to Lichee Pi
Lichee login:
Welcome to Lichee Pi
Lichee login: root
# ls
# cd /
# ls
bin      lib      media    proc     sbin     usr
dev      lib32    mnt      root     sys      var
etc      linuxrc  opt      run      tmp
#

用户名:root,无密码
跑起来了!!

七、进入文件系统后的操作

查看挂载的文件系统

# mount
ubi0:rootfs on / type ubifs (rw,relatime,assert=read-only,ubi=0,vol=0)
devtmpfs on /dev type devtmpfs (rw,relatime,size=27000k,nr_inodes=6750,mode=755)
proc on /proc type proc (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620,ptmxmode=000)
tmpfs on /dev/shm type tmpfs (rw,relatime,mode=777)
tmpfs on /tmp type tmpfs (rw,relatime)
tmpfs on /run type tmpfs (rw,nosuid,nodev,relatime,mode=755)
sysfs on /sys type sysfs (rw,relatime)

查看分区

# cat /proc/mtd*
dev:    size   erasesize  name
mtd0: 00100000 00020000 "uboot"
mtd1: 00020000 00020000 "dtb"
mtd2: 00500000 00020000 "kernel"
mtd3: 079e0000 00020000 "rootfs"
# ls /dev/mtd*
/dev/mtd0    /dev/mtd1    /dev/mtd2    /dev/mtd3
/dev/mtd0ro  /dev/mtd1ro  /dev/mtd2ro  /dev/mtd3ro

查看存储

# df -h
Filesystem                Size      Used Available Use% Mounted on
ubi0:rootfs              80.1M      2.1M     78.0M   3% /
devtmpfs                 26.4M         0     26.4M   0% /dev
tmpfs                    26.9M         0     26.9M   0% /dev/shm
tmpfs                    26.9M     20.0K     26.8M   0% /tmp
tmpfs                    26.9M     16.0K     26.9M   0% /run

查看Linux内核启动参数

# cat /proc/cmdline
console=ttyS0,115200 earlyprintk panic=5 rootwait mtdparts=spi0.0:1M(uboot)ro,128k(dtb)ro,5M(kernel)ro,-(rootfs) ubi.mtd=3 root=ubi0:rootfs rw rootfstype=ubifs

查看目录信息

# ls -lh
total 0
drwxr-xr-x    2 1000     1000        4.5K Mar 24  2017 bin
drwxr-xr-x    8 root     root       12.3K Jan  1 00:35 dev
drwxr-xr-x    5 1000     1000        1.5K Jan  1 00:35 etc
drwxr-xr-x    2 1000     1000        2.3K Mar 24  2017 lib
lrwxrwxrwx    1 1000     1000           3 Sep 17  2023 lib32 -> lib
lrwxrwxrwx    1 1000     1000          11 Sep 17  2023 linuxrc -> bin/busybox
drwxr-xr-x    2 1000     1000         160 Feb 28  2017 media
drwxr-xr-x    2 1000     1000         160 Feb 28  2017 mnt
drwxr-xr-x    3 1000     1000         224 Feb 26  2022 opt
dr-xr-xr-x   44 root     root           0 Jan  1 00:00 proc
drwx------    2 1000     1000         232 Jan  1 00:35 root
drwxr-xr-x    3 root     root         140 Jan  1 00:35 run
drwxr-xr-x    2 1000     1000        3.5K Mar 24  2017 sbin
dr-xr-xr-x   12 root     root           0 Jan  1 00:35 sys
drwxrwxrwt    2 root     root          60 Jan  1 00:35 tmp
drwxr-xr-x    6 1000     1000         480 Mar 24  2017 usr
drwxr-xr-x    4 1000     1000         672 Mar 24  2017 var

八、总结

编译Uboot

make clean
make ARCH=arm LicheePi_Zero_Spinand_defconfig
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf-
./gen_sunxi_spinand_onlyboot_img.sh split.bin u-boot-sunxi-with-spl.bin 2048 128

编译Linux Kernel

make clean
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- licheepi_zero_spinand_defconfig
time make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- -j16
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- dtbs

九、打包

拷贝

cp ../u-boot-2022.04-spinand/split.bin ./
cp ../linux-zero-5.2.y-spinand/arch/arm/boot/zImage ./
cp ../linux-zero-5.2.y-spinand/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dtb ./
tar -xvf rootfs.tarsudo ./step1_gen_rootfs_ubifs_img.sh
sudo ./step2_gen_ubi_img.sh
sudo ./step3_gen_flash_img.sh
0x0      ~ 0xFFFFF  : 0x100000    1 MiB
0x100000 ~ 0x11FFFF  : 0x20000     128 KiB
0x120000 ~ 0x61FFFF  : 0x500000    5 MiB
0x620000 ~ 0x7FFFFFF  : 0x79DFFFF  124800 KiB=121.875 MiB

打包脚本 step3_gen_flash_img.sh

#!/bin/bash
rm -f flashimg.bin
dd if=/dev/zero of=flashimg.bin bs=1M count=20
dd if=u-boot-sunxi-with-spl.bin_split_exp of=flashimg.bin bs=1K count=1024 conv=notrunc
dd if=sun8i-v3s-licheepi-zero.dtb of=flashimg.bin bs=1K count=128 seek=1024 conv=notrunc
dd if=zImage of=flashimg.bin bs=1K count=5120 seek=1152 conv=notrunc
dd if=ubi.img of=flashimg.bin  bs=1K seek=6272 conv=notrunc

烧录:

sudo xfel spinand erase 0x0 0x8000000
sudo xfel spinand write 0 flashimg.bin

十、工程源码

原始的文件:

在这里插入图片描述

链接:https://pan.baidu.com/s/1uvlJGbLpLvEWhCeeKw6o9w
提取码:lief
–来自百度网盘超级会员V5的分享

配置好的文件:

在这里插入图片描述

链接:https://pan.baidu.com/s/1x2_cxEVv75nfhLBARodRwQ
提取码:lief
–来自百度网盘超级会员V5的分享

参考:

  • 全志V3S嵌入式驱动开发(spi-nand image制作)
  • https://whycan.com/t_3123.html
  • https://whycan.com/viewtopic.php?pid=91704#p91704
  • https://whycan.com/p_80604.html

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处:http://www.mzph.cn/news/85395.shtml

如若内容造成侵权/违法违规/事实不符,请联系多彩编程网进行投诉反馈email:809451989@qq.com,一经查实,立即删除!

相关文章

rabbitMQ (1)

文章目录 1. RabbitMQ 介绍1.1 几个重要概念1.2 RabbitMq 的工作原理 2 RabbitMQ 安装3. RabbitMQ 入门操作3.1 添加依赖3.2 生产者代码3.3 消费者代码 4. Work Queues5. 管理端页面创建队列 1. RabbitMQ 介绍 引用 &#xff1a; RabbitMQ 是一个消息中间件&#xff1a;它接受…

Xilinx FPGA 程序固化重新上电程序不运行的问题

问题描述 FPGA直接下载bit文件,功能正常。 FPGA擦除FLASH,烧写FLASH,正常。 电源断电,重新上电,FALSH里面的程序没有启动,FPGA程序没有跑起来。–FLASH启动不正常。 解决办法 在XDC约束文件里边增加约束: ## Configuration options, can be used for all designs se…

[Linux入门]---Linux项目自动化构建工具-make/Makefile

目录 1.背景2.make指令输入make默认为Makefile文件第一条指令执行Makefile文件对gcc指令特殊处理及原理特殊符号 3.总结 1.背景 会不会写makefile&#xff0c;从一个侧面说明了一个人是否具备完成大型工程的能力一个工程中的源文件不计数&#xff0c;其按类型、功能、模块分别放…

CNN(九):Inception v3算法实战

&#x1f368; 本文为&#x1f517;365天深度学习训练营 中的学习记录博客 &#x1f356; 原作者&#xff1a;K同学啊|接辅导、项目定制 1 理论基础 Inception v3论文 Inception v3由谷歌研究员Christian Szegedy等人在2015年的论文《Rethinking the Inception Architecture f…

Jmeter集成到jenkins

Jmeter集成到Jenkins Jmeter集成到Jenkins. 1 软件下载... 4 一:环境配置... 4 1.JDK安装&#xff1a;... 4 配置JDK环境变量... 5 2.Jmeter安装&#xff1a;... 5 配置jmeter环境变量... 6 3.安装Ant 7 配置Ant环境变量... 7 4.Git安装&#xff1a;... 8 配置git环境…

Untiy UDP局域网 异步发送图片

同步画面有问题&#xff0c;传图片吧 using System.Text; using System.Net.Sockets; using System.Collections; using System.Collections.Generic; using UnityEngine; using UnityEngine.Events; using System.Net; using System; using System.Threading.Tasks; using Sy…

java内嵌浏览器CEF-JAVA、jcef、java chrome

java内嵌浏览器CEF-JAVA、jcef、java chrome jcef是老牌cef的chrome内嵌方案&#xff0c;可以进行java-chrome-h5-桌面开发&#xff0c;下面为最新版本&#xff08;2023年9月22日10:33:07&#xff09; JCEF&#xff08;Java Chromium Embedded Framework&#xff09;是一个基于…

Cesium 空间量算——生成点位坐标

文章目录 需求分析1. 点击坐标点实现2. 输入坐标实现 需求 用 Cesium 生成点位坐标&#xff0c;并明显标识 分析 以下是我的两种实现方式 第一种是坐标点击实现 第二种是输入坐标实现 1. 点击坐标点实现 //点位坐标getLocation() {this.hoverIndex 0;let that this;this.view…

板子接线图

1.ST-LINK V2接线 2.对抗板子刷蓝牙固件 接USB转TTL&#xff0c;用镊子短接两个孔 2.对抗板子用串口测试蓝牙AT命令 短接白色箭头&#xff0c;接TX&#xff0c;RX&#xff0c;电源

MongoDB【部署 04】Windows系统实现MongoDB多磁盘存储

Windows系统实现多磁盘存储 1.为什么2.多磁盘存储2.1 数据库配置2.2 文件夹磁盘映射2.3 创建新的数据集 3.总结 1.为什么 这里仅针对只有一台Windows系统服务器的情景&#xff1a; 当服务器存储不足时&#xff0c;或者要接入更多的数据&#xff0c;就会挂载新磁盘&#xff0c…

边缘计算AI智能安防监控视频平台车辆违停算法详解与应用

随着城市车辆保有量呈现高速增长趋势&#xff0c;交通拥堵、违章行为也日益泛滥。因为车辆未停放在指定区域导致的车位浪费、占用/堵塞交通要道、车辆剐蹭等问题层出不穷。通过人工进行违法停车的监控&#xff0c;不仅让监控人员工作负荷越来越大&#xff0c;而且存在发现不及时…

Lua学习笔记:词法分析

前言 本篇在讲什么 Lua的词法分析 本篇需要什么 对Lua语法有简单认知 对C语法有简单认知 依赖Visual Studio工具 本篇的特色 具有全流程的图文教学 重实践&#xff0c;轻理论&#xff0c;快速上手 提供全流程的源码内容 ★提高阅读体验★ &#x1f449; ♠ 一级标题…

SpringAOP补充-通知获取类型

JoinPoint 是 ProceedingJoinPoint 的父类。 getArgs()是JoinPoint获取原方法返回值的函数。 preceed()是ProceedingJoinPoint获取原方法返回值的函数。

【Java】Servlet API

Servlet API HttpServlet核心方法Servlet生命周期 HttpServletRequest核心方法 HttpServletResponse核心方法 HttpServlet 我们写 Servlet 代码的时候, 首先第一步就是先创建类, 继承自 HttpServlet, 并重写其中的某些方法. 核心方法 方法名称调用时机init在 HttpServlet 实…

近三年各领域数字孪生相关政策汇编(可下载)

自2021年国家“十四五”规划纲要提出“探索建设数字孪生城市”以来&#xff0c;国家发展和改革委员会、工业和信息化部、住房和城乡建设部、水利部、农业农村部等部门纷纷出台政策&#xff0c;大力推动数字孪生在千行百业的落地发展。这些政策不仅为数字孪生的应用提供了广阔的…

39 | selenium基础架构,UI测试架构

什么是测试基础架构&#xff1f; 测试基础架构指的是&#xff0c;执行测试的过程中用到的所有基础硬件设施以及相关的软件设施。因此&#xff0c;我们也把测试基础架构称之为广义的测试执行环境。通常来讲&#xff0c;测试基础架构主要包括以下内容&#xff1a; 执行测试的机器…

机器学习第十一课--K-Means聚类

一.聚类的概念 K-Means算法是最经典的聚类算法&#xff0c;几乎所有的聚类分析场景&#xff0c;你都可以使用K-Means&#xff0c;而且在营销场景上&#xff0c;它就是"King"&#xff0c;所以不管从事数据分析师甚至是AI工程师&#xff0c;不知道K-Means是”不可原谅…

MATLAB | R2023b更新了哪些好玩的东西?

R2023b来啦&#xff01;&#xff01;废话不多说看看新版本有啥有趣的玩意和好玩的特性叭&#xff01;&#xff01;依旧把绘图放最前面叭&#xff0c;有图的内容看的人多。。 1 调色板 MATLAB终于不只有一套配色了&#xff0c;诸君且看&#xff1a; y [3 5 7 9 11; 2 5 6 8 1…

uniapp确认提示框;uniapp判断输入框值是否符合正常手机号,身份证号

确认提示框 UniApp 中&#xff0c;你可以使用 uni.showModal 方法来创建确认提示框。以下是一个示例&#xff1a; <template><view class"container"><button click"showAuthModal">显示确认提示框</button></view> </…

【问题记录】解决“命令行终端”和“Git Bash”操作本地Git仓库时出现 中文乱码 的问题!

环境 Windows 11 家庭中文版git version 2.41.0.windows.1 问题情况 在使用 “命令行终端” 和 “Git Bash” 在本地Git仓库敲击命令时&#xff0c;对中文名称文件显示一连串的数字&#xff0c;如下所示&#xff1a;这种情况通常是由于字符编码设置不正确所引起的 解决办法 设置…