组网需求
如图1所示，SwitchA通过SwitchB和NMS跨网段相连。在SwitchA上通过静态路由与NMS进行正常通信。在SwitchA和SwitchB之间实现毫秒级故障感知，提高收敛速度
配置思路
采用如下思路配置IPv4静态路由与静态BFD联动：
-
在SwitchA和SwitchB上配置BFD Session，在SwitchA和SwitchB之间实现毫秒级故障感知，提高收敛速度。
-
配置SwitchA到NMS的静态路由并绑定BFD Session，实现毫秒级故障感知，提高收敛速度。
操作步骤
配置各接口所属的VLAN
# 配置SwitchA。SwitchB的配置与SwitchA类似
[zhongwanzhiA]vlan 10
[zhongwanzhiA]interface GigabitEthernet 0/0/1
[zhongwanzhiA-GigabitEthernet0/0/1]port link-type trunk
[zhongwanzhiA-GigabitEthernet0/0/1]port trunk allow-pass vlan 10
[zhongwanzhiA-GigabitEthernet0/0/1]quit配置各VLANIF接口的IP地址
# 配置SwitchA。SwitchB的配置与SwitchA类似
[zhongwanzhiA]interface Vlanif 10
[zhongwanzhiA-Vlanif10]ip add
[zhongwanzhiA-Vlanif10]ip address 10.1.1.1 24
[zhongwanzhiA-Vlanif10]quit配置SwitchA和SwitchB间的BFD会话
# 在SwitchA配置与SwitchB间的BFD Session。
[zhongwanzhiA]bfd
[zhongwanzhiA-bfd]quit
[zhongwanzhiA]bfd aa bind peer-ip 10.1.1.2
[zhongwanzhiA-bfd-session-aa]discriminator local 10
[zhongwanzhiA-bfd-session-aa]discriminator remote 20
[zhongwanzhiA-bfd-session-aa]commit
[zhongwanzhiA-bfd-session-aa]quit# 在SwitchB配置与SwitchA之间的BFD Session。
[zhongwanzhiB]bfd
[zhongwanzhiB-bfd]quit
[zhongwanzhiB]bfd bb bind peer-ip 10.1.1.1
[zhongwanzhiB-bfd-session-bb]discriminator local 20
[zhongwanzhiB-bfd-session-bb]discriminator remote 10
[zhongwanzhiB-bfd-session-bb]commit
[zhongwanzhiB-bfd-session-bb]quit配置静态路由并绑定BFD会话
# 在SwitchA配置到外部网络的静态路由，并绑定BFD会话aa
[zhongwanzhiA]ip route-static 10.2.2.0 24 10.1.1.2 track bfd-session aa验证配置结果
# 配置完成后，在SwitchA和SwitchB上执行display bfd session all命令，可以看到BFD会话已经建立，且状态为Up。SwitchA上的显示为例。
[zhongwanzhiA]display bfd session all
--------------------------------------------------------------------------------
Local Remote PeerIpAddr State Type InterfaceName
--------------------------------------------------------------------------------10 20 10.1.1.2 Up S_IP_PEER -
--------------------------------------------------------------------------------Total UP/DOWN Session Number : 1/0# 在SwitchA查看IP路由表，静态路由存在于路由表中
[zhongwanzhiA]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: PublicDestinations : 5 Routes : 5 Destination/Mask Proto Pre Cost Flags NextHop Interface10.1.1.0/24 Direct 0 0 D 10.1.1.1 Vlanif1010.1.1.1/32 Direct 0 0 D 127.0.0.1 Vlanif1010.2.2.0/24 Static 60 0 RD 10.1.1.2 Vlanif10127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0[zhongwanzhiA]为什么要做BDF会话服 ：因为当BFD检测到链路恢复正常后，就会迅速通知所绑定的静态路由重新生效
