本文主要探讨210的LCD相关知识。
LCD
LCD称液晶(透光+背光呈色),可在电信号驱动下使液晶分子旋转,呈现不同的颜色(被动发光)
lcd接口为TTL接口(+5V为1，0V为0),不能传输太远,远距离传输方式:SoC(TTL) ->VGA-> LCD(TTL)
其他显设备:CRT(阴极摄像管显示器),OLED,LED
RGB接口:VD0~23 24根数据线,HSYNC水平同步信号,VSYNC垂直同步信号,VCLK像素时钟,VDEN数据有效标志,LEND行结束标志
lcd显示
像素是组成图像的最基本元素(最小单位),扫描频率为刷新率
LCD显示单位为帧(一画面),一帧为多行,一行为多像素(像素矩阵)
LCD控制器通过数字接口给LCD驱动器提供数字信号
LCD驱动器给面板提供模拟电信号
显存是LCD控制器读取像素数据传输给LCD驱动器的区域
像素间距（pitch）是连续2个像素中心距离
分辨率（resolution）:屏幕的横纵像素个数就叫分辨率(210是800×480)
像素深度（bpp）:计算机用二进制位来表示像素的数据,位越多像素颜色值越多(1、8、16、24、32位)
24位：24二进制位表示颜色可表示16777216种颜色(RGB888分布)
210LCD控制器叫FIMD与AHB总线连接,对外部提供RGB接口、I80接口、YUV接口
210LCD控制器有5个虚拟屏幕Window0~Window4
HSPW水平同步信号脉宽
HBPD水平同步信号前肩
HFPD水平同步信号后肩
VSPW垂直同步信号脉宽
VBPD垂直同步信号前肩
VFPD垂直同步信号后肩
一行像素数据显示(LCD兼容):LCD控制器发送HSYNC高电平脉冲（宽度为HSPW）,HBPD+有效行信息+HFPD(三部分)或HSPW+HBPD+有效行信息+HFPD(四部分)
一帧帧图像显示(LCD兼容)：VSPW(帧同步信号宽度)+VBPD+帧有效信号+VFPD
210的LCD时序参数
h_fp = 210
h_bp = 38
h_sw = 10
v_fp = 22
v_fpe = 1
v_bp = 18
v_bpe = 1
v_sw = 7
210lcd寄存器
gpio
GPF0CON~GPF3CON(配置lcd功能)
GPD0CON，GPD0DAT（配置背光）
lcd寄存器
DISPLAY_CONTROL设置rgb模式（10或11）
VIDCON0~VIDCON3：配置LCD主控制
VIDTCON0~VIDTCON3：设置时序
VINCON0~VINCON4：设置window
设置发送数据的通道
设置坐标和范围
设置window0 起始地址和缓存
demo:
画线,画圆,写英文,显示图片
Makefile(主)：
all:make -C ./bl1 make -C ./bl2
clean:make clean -C ./bl1make clean -C ./bl2writersd
#!/bin/sh
dd iflag=dsync oflag=dsync if=./bl1/sd1.bin of=/dev/sdb seek=1
dd iflag=dsync oflag=dsync if=./bl2/sd2.bin of=/dev/sdb seek=45bl1:
start.S
#define WTCON 0xE2700000
#define SVC_STACK 0xd0037d80
#define SOFT_SW 0xE010E81C.global _start_start://set soft switcher,mean set XEINT[0] as PS_HOLD_OUT_EN,set output high levelldr r0, =SOFT_SWldr r1, [r0]orr r1, r1, #0x300orr r1, r1, #0x01str r1, [r0]//close WatchDogldr r0,=WTCONldr r1,=0x0str r1,[r0]//init SVC stackldr sp,=SVC_STACK//init icachemrc p15,0,r0,c1,c0,0bic r0,r0,#(1<<12) //close icacheorr r0,r0,#(1<<12) //open icachemcr p15,0,r0,c1,c0,0 bl sdram_asm_init//use funcbl copy_bl2_2_ddrb .s5pv210.h
/* S5PC110 device base addresses */
#define ELFIN_DMA_BASE 0xE0900000
#define ELFIN_LCD_BASE 0xF8000000
#define ELFIN_USB_HOST_BASE 0xEC200000
#define ELFIN_I2C_BASE 0xE1800000
#define ELFIN_I2S_BASE 0xE2100000
#define ELFIN_ADC_BASE 0xE1700000
#define ELFIN_SPI_BASE 0xE1300000#define ELFIN_HSMMC_0_BASE 0xEB000000
#define ELFIN_HSMMC_1_BASE 0xEB100000
#define ELFIN_HSMMC_2_BASE 0xEB200000
#define ELFIN_HSMMC_3_BASE 0xEB300000#define ELFIN_CLOCK_POWER_BASE 0xE0100000#define IO_RET_REL ((1 << 31) | (1 << 29) | (1 << 28))/* Clock & Power Controller for s5pc110*/
#define APLL_LOCK_OFFSET 0x00
#define MPLL_LOCK_OFFSET 0x08
#define EPLL_LOCK_OFFSET 0x10
#define VPLL_LOCK_OFFSET 0x20
#define APLL_CON0_OFFSET 0x100
#define APLL_CON1_OFFSET 0x104
#define MPLL_CON_OFFSET 0x108
#define EPLL_CON_OFFSET 0x110
#define VPLL_CON_OFFSET 0x120#define CLK_SRC0_OFFSET 0x200
#define CLK_SRC1_OFFSET 0x204
#define CLK_SRC2_OFFSET 0x208
#define CLK_SRC3_OFFSET 0x20c
#define CLK_SRC4_OFFSET 0x210
#define CLK_SRC5_OFFSET 0x214
#define CLK_SRC6_OFFSET 0x218
#define CLK_SRC_MASK0_OFFSET 0x280
#define CLK_SRC_MASK1_OFFSET 0x284#define CLK_DIV0_OFFSET 0x300
#define CLK_DIV1_OFFSET 0x304
#define CLK_DIV2_OFFSET 0x308
#define CLK_DIV3_OFFSET 0x30c
#define CLK_DIV4_OFFSET 0x310
#define CLK_DIV5_OFFSET 0x314
#define CLK_DIV6_OFFSET 0x318
#define CLK_DIV7_OFFSET 0x31c#define CLK_GATE_IP0_OFFSET 0x460
#define CLK_GATE_IP1_OFFSET 0x464
#define CLK_GATE_IP2_OFFSET 0x468
#define CLK_GATE_IP3_OFFSET 0x46c
#define CLK_GATE_IP4_OFFSET 0x470
#define CLK_GATE_BLOCK_OFFSET 0x480#define CLK_OUT_OFFSET 0x500
#define CLK_DIV_STAT0_OFFSET 0x1000
#define CLK_DIV_STAT1_OFFSET 0x1004
#define CLK_MUX_STAT0_OFFSET 0x1100
#define CLK_MUX_STAT1_OFFSET 0x1104
#define SW_RST_OFFSET 0x2000#define ONEDRAM_CFG_OFFSET 0x6208#define OSC_CON_OFFSET 0x8000
#define RST_STAT_OFFSET 0xa000
#define PWR_CFG_OFFSET 0xc000
#define EINT_WAKEUP_MASK_OFFSET 0xc004
#define WAKEUP_MASK_OFFSET 0xc008
#define NORMAL_CFG_OFFSET 0xc010
#define IDLE_CFG_OFFSET 0xc020
#define STOP_CFG_OFFSET 0xc030
#define STOP_MEM_CFG_OFFSET 0xc034
#define SLEEP_CFG_OFFSET 0xc040
#define OSC_FREQ_OFFSET 0xc100
#define OSC_STABLE_OFFSET 0xc104
#define PWR_STABLE_OFFSET 0xc108
#define MTC_STABLE_OFFSET 0xc110
#define CLAMP_STABLE_OFFSET 0xc114
#define WAKEUP_STAT_OFFSET 0xc200
#define BLK_PWR_STAT_OFFSET 0xc204
#define BODY_BIAS_CON_OFFSET 0xc300
#define ION_SKEW_CON_OFFSET 0xc310
#define ION_SKEW_MON_OFFSET 0xc314
#define IOFF_SKEW_CON_OFFSET 0xc320
#define IOFF_SKEW_MON_OFFSET 0xc324
#define OTHERS_OFFSET 0xe000
#define OM_STAT_OFFSET 0xe100
#define MIE_CONTROL_OFFSET 0xe800
#define HDMI_CONTROL_OFFSET 0xe804
#define USB_PHY_CONTROL_OFFSET 0xe80c
#define DAC_CONTROL_OFFSET 0xe810
#define MIPI_DPHY_CONTROL_OFFSET 0xe814
#define ADC_CONTROL_OFFSET 0xe818
#define PS_HOLD_CONTROL_OFFSET 0xe81c#define INFORM0_OFFSET 0xf000
#define INFORM1_OFFSET 0xf004
#define INFORM2_OFFSET 0xf008
#define INFORM3_OFFSET 0xf00c
#define INFORM4_OFFSET 0xf010
#define INFORM5_OFFSET 0xf014
#define INFORM6_OFFSET 0xf018
#define INFORM7_OFFSET 0xf01c#define INF_REG0_OFFSET 0x00
#define INF_REG1_OFFSET 0x04
#define INF_REG2_OFFSET 0x08
#define INF_REG3_OFFSET 0x0c
#define INF_REG4_OFFSET 0x10
#define INF_REG5_OFFSET 0x14
#define INF_REG6_OFFSET 0x18
#define INF_REG7_OFFSET 0x1c/** GPIO*/
#define ELFIN_GPIO_BASE 0xE0200000#define GPA0CON_OFFSET 0x000
#define GPA0DAT_OFFSET 0x004
#define GPA0PUD_OFFSET 0x008
#define GPA0DRV_SR_OFFSET 0x00C
#define GPA0CONPDN_OFFSET 0x010
#define GPA0PUDPDN_OFFSET 0x014#define GPA1CON_OFFSET 0x020
#define GPA1DAT_OFFSET 0x024
#define GPA1PUD_OFFSET 0x028
#define GPA1DRV_SR_OFFSET 0x02C
#define GPA1CONPDN_OFFSET 0x030
#define GPA1PUDPDN_OFFSET 0x034#define GPBCON_OFFSET 0x040
#define GPBDAT_OFFSET 0x044
#define GPBPUD_OFFSET 0x048
#define GPBDRV_SR_OFFSET 0x04C
#define GPBCONPDN_OFFSET 0x050
#define GPBPUDPDN_OFFSET 0x054#define GPC0CON_OFFSET 0x060
#define GPC0DAT_OFFSET 0x064
#define GPC0PUD_OFFSET 0x068
#define GPC0DRV_SR_OFFSET 0x06C
#define GPC0CONPDN_OFFSET 0x070
#define GPC0PUDPDN_OFFSET 0x074#define GPC1CON_OFFSET 0x080
#define GPC1DAT_OFFSET 0x084
#define GPC1PUD_OFFSET 0x088
#define GPC1DRV_SR_OFFSET 0x08C
#define GPC1CONPDN_OFFSET 0x090
#define GPC1PUDPDN_OFFSET 0x094#define GPD0CON_OFFSET 0x0A0
#define GPD0DAT_OFFSET 0x0A4
#define GPD0PUD_OFFSET 0x0A8
#define GPD0DRV_SR_OFFSET 0x0AC
#define GPD0CONPDN_OFFSET 0x0B0
#define GPD0PUDPDN_OFFSET 0x0B4#define GPD1CON_OFFSET 0x0C0
#define GPD1DAT_OFFSET 0x0C4
#define GPD1PUD_OFFSET 0x0C8
#define GPD1DRV_SR_OFFSET 0x0CC
#define GPD1CONPDN_OFFSET 0x0D0
#define GPD1PUDPDN_OFFSET 0x0D4#define GPE0CON_OFFSET 0x0E0
#define GPE0DAT_OFFSET 0x0E4
#define GPE0PUD_OFFSET 0x0E8
#define GPE0DRV_SR_OFFSET 0x0EC
#define GPE0CONPDN_OFFSET 0x0F0
#define GPE0PUDPDN_OFFSET 0x0F4#define GPE1CON_OFFSET 0x100
#define GPE1DAT_OFFSET 0x104
#define GPE1PUD_OFFSET 0x108
#define GPE1DRV_SR_OFFSET 0x10C
#define GPE1CONPDN_OFFSET 0x110
#define GPE1PUDPDN_OFFSET 0x114#define GPF0CON_OFFSET 0x120
#define GPF0DAT_OFFSET 0x124
#define GPF0PUD_OFFSET 0x128
#define GPF0DRV_SR_OFFSET 0x12C
#define GPF0CONPDN_OFFSET 0x130
#define GPF0PUDPDN_OFFSET 0x134#define GPF1CON_OFFSET 0x140
#define GPF1DAT_OFFSET 0x144
#define GPF1PUD_OFFSET 0x148
#define GPF1DRV_SR_OFFSET 0x14C
#define GPF1CONPDN_OFFSET 0x150
#define GPF1PUDPDN_OFFSET 0x154#define GPF2CON_OFFSET 0x160
#define GPF2DAT_OFFSET 0x164
#define GPF2PUD_OFFSET 0x168
#define GPF2DRV_SR_OFFSET 0x16C
#define GPF2CONPDN_OFFSET 0x170
#define GPF2PUDPDN_OFFSET 0x174#define GPF3CON_OFFSET 0x180
#define GPF3DAT_OFFSET 0x184
#define GPF3PUD_OFFSET 0x188
#define GPF3DRV_SR_OFFSET 0x18C
#define GPF3CONPDN_OFFSET 0x190
#define GPF3PUDPDN_OFFSET 0x194#define GPG0CON_OFFSET 0x1A0
#define GPG0DAT_OFFSET 0x1A4
#define GPG0PUD_OFFSET 0x1A8
#define GPG0DRV_SR_OFFSET 0x1AC
#define GPG0CONPDN_OFFSET 0x1B0
#define GPG0PUDPDN_OFFSET 0x1B4#define GPG1CON_OFFSET 0x1C0
#define GPG1DAT_OFFSET 0x1C4
#define GPG1PUD_OFFSET 0x1C8
#define GPG1DRV_SR_OFFSET 0x1CC
#define GPG1CONPDN_OFFSET 0x1D0
#define GPG1PUDPDN_OFFSET 0x1D4#define GPG2CON_OFFSET 0x1E0
#define GPG2DAT_OFFSET 0x1E4
#define GPG2PUD_OFFSET 0x1E8
#define GPG2DRV_SR_OFFSET 0x1EC
#define GPG2CONPDN_OFFSET 0x1F0
#define GPG2PUDPDN_OFFSET 0x1F4#define GPG3CON_OFFSET 0x200
#define GPG3DAT_OFFSET 0x204
#define GPG3PUD_OFFSET 0x208
#define GPG3DRV_SR_OFFSET 0x20C
#define GPG3CONPDN_OFFSET 0x210
#define GPG3PUDPDN_OFFSET 0x214#define MP1_0DRV_SR_OFFSET 0x3CC
#define MP1_1DRV_SR_OFFSET 0x3EC
#define MP1_2DRV_SR_OFFSET 0x40C
#define MP1_3DRV_SR_OFFSET 0x42C
#define MP1_4DRV_SR_OFFSET 0x44C
#define MP1_5DRV_SR_OFFSET 0x46C
#define MP1_6DRV_SR_OFFSET 0x48C
#define MP1_7DRV_SR_OFFSET 0x4AC
#define MP1_8DRV_SR_OFFSET 0x4CC#define MP2_0DRV_SR_OFFSET 0x4EC
#define MP2_1DRV_SR_OFFSET 0x50C
#define MP2_2DRV_SR_OFFSET 0x52C
#define MP2_3DRV_SR_OFFSET 0x54C
#define MP2_4DRV_SR_OFFSET 0x56C
#define MP2_5DRV_SR_OFFSET 0x58C
#define MP2_6DRV_SR_OFFSET 0x5AC
#define MP2_7DRV_SR_OFFSET 0x5CC
#define MP2_8DRV_SR_OFFSET 0x5EC/* GPH0 */
#define GPH0CON_OFFSET 0xc00
#define GPH0DAT_OFFSET 0xc04
#define GPH0PUD_OFFSET 0xc08
#define GPH0DRV_OFFSET 0xc0c/* GPH1 */
#define GPH1CON_OFFSET 0xc20
#define GPH1DAT_OFFSET 0xc24
#define GPH1PUD_OFFSET 0xc28
#define GPH1DRV_OFFSET 0xc2c/* GPH2 */
#define GPH2CON_OFFSET 0xc40
#define GPH2DAT_OFFSET 0xc44
#define GPH2PUD_OFFSET 0xc48
#define GPH2DRV_OFFSET 0xc4c/* GPH3 */
#define GPH3CON_OFFSET 0xc60
#define GPH3DAT_OFFSET 0xc64
#define GPH3PUD_OFFSET 0xc68
#define GPH3DRV_OFFSET 0xc6c#define GPICON_OFFSET 0x220
#define GPIPUD_OFFSET 0x228
#define GPIDRV_OFFSET_SR 0x22C
#define GPIPUDPDN_OFFSET 0x234#define GPJ0CON_OFFSET 0x240
#define GPJ0DAT_OFFSET 0x244
#define GPJ0PUD_OFFSET 0x248
#define GPJ0DRV_SR_OFFSET 0x24C
#define GPJ0CONPDN_OFFSET 0x250
#define GPJ0PUDPDN_OFFSET 0x254#define GPJ1CON_OFFSET 0x260
#define GPJ1DAT_OFFSET 0x264
#define GPJ1PUD_OFFSET 0x268
#define GPJ1DRV_SR_OFFSET 0x26C
#define GPJ1CONPDN_OFFSET 0x270
#define GPJ1PUDPDN_OFFSET 0x274#define GPJ2CON_OFFSET 0x280
#define GPJ2DAT_OFFSET 0x284
#define GPJ2PUD_OFFSET 0x288
#define GPJ2DRV_SR_OFFSET 0x28C
#define GPJ2CONPDN_OFFSET 0x290
#define GPJ2PUDPDN_OFFSET 0x294#define GPJ3CON_OFFSET 0x2A0
#define GPJ3DAT_OFFSET 0x2A4
#define GPJ3PUD_OFFSET 0x2A8
#define GPJ3DRV_SR_OFFSET 0x2AC
#define GPJ3CONPDN_OFFSET 0x2B0
#define GPJ3PUDPDN_OFFSET 0x2B4#define GPJ4CON_OFFSET 0x2C0
#define GPJ4DAT_OFFSET 0x2C4
#define GPJ4PUD_OFFSET 0x2C8
#define GPJ4DRV_SR_OFFSET 0x2CC
#define GPJ4CONPDN_OFFSET 0x2D0
#define GPJ4PUDPDN_OFFSET 0x2D4/** Interrupt*/
#define ELFIN_VIC0_BASE_ADDR (0xF2000000)
#define ELFIN_VIC1_BASE_ADDR (0xF2100000)
#define ELFIN_VIC2_BASE_ADDR (0xF2200000)#define ELFIN_TZIC0_BASE_ADDR (0xF2800000)
#define ELFIN_TZIC1_BASE_ADDR (0xF2900000)
#define ELFIN_TZIC2_BASE_ADDR (0xF2A00000)#define oINTMOD (0x0C) // VIC INT SELECT (IRQ or FIQ)
#define oINTUNMSK (0x10) // VIC INT EN (Unmask by writing 1)
#define oINTMSK (0x14) // VIC INT EN CLEAR (Mask by writing 1)
#define oINTSUBMSK (0x1C) // VIC SOFT INT CLEAR
#define oVECTADDR (0xF00) // VIC ADDRESS/** Watchdog timer*/
#define ELFIN_WATCHDOG_BASE 0xE2700000#define WTCON_OFFSET 0x00
#define WTDAT_OFFSET 0x08
#define WTCNT_OFFSET 0x0C#define WTCON_REG __REG(ELFIN_WATCHDOG_BASE+WTCON_OFFSET)
#define WTDAT_REG __REG(ELFIN_WATCHDOG_BASE+WTDAT_OFFSET)
#define WTCNT_REG __REG(ELFIN_WATCHDOG_BASE+WTCNT_OFFSET)/** UART*/
#define ELFIN_UART_BASE 0XE2900000#define ELFIN_UART0_OFFSET 0x0000
#define ELFIN_UART1_OFFSET 0x0400
#define ELFIN_UART2_OFFSET 0x0800
#define ELFIN_UART3_OFFSET 0x0c00#if defined(CONFIG_SERIAL0)
#define ELFIN_UART_CONSOLE_BASE (ELFIN_UART_BASE + ELFIN_UART0_OFFSET)
#elif defined(CONFIG_SERIAL1)
#define ELFIN_UART_CONSOLE_BASE (ELFIN_UART_BASE + ELFIN_UART1_OFFSET)
#elif defined(CONFIG_SERIAL2)
#define ELFIN_UART_CONSOLE_BASE (ELFIN_UART_BASE + ELFIN_UART2_OFFSET)
#elif defined(CONFIG_SERIAL3)
#define ELFIN_UART_CONSOLE_BASE (ELFIN_UART_BASE + ELFIN_UART3_OFFSET)
#else
#define ELFIN_UART_CONSOLE_BASE (ELFIN_UART_BASE + ELFIN_UART0_OFFSET)
#endif#define ULCON_OFFSET 0x00
#define UCON_OFFSET 0x04
#define UFCON_OFFSET 0x08
#define UMCON_OFFSET 0x0C
#define UTRSTAT_OFFSET 0x10
#define UERSTAT_OFFSET 0x14
#define UFSTAT_OFFSET 0x18
#define UMSTAT_OFFSET 0x1C
#define UTXH_OFFSET 0x20
#define URXH_OFFSET 0x24
#define UBRDIV_OFFSET 0x28
#define UDIVSLOT_OFFSET 0x2C
#define UINTP_OFFSET 0x30
#define UINTSP_OFFSET 0x34
#define UINTM_OFFSET 0x38#define UTRSTAT_TX_EMPTY BIT2
#define UTRSTAT_RX_READY BIT0
#define UART_ERR_MASK 0xF/** PWM timer*/
#define ELFIN_TIMER_BASE 0xE2500000#define TCFG0_REG __REG(0xE2500000)
#define TCFG1_REG __REG(0xE2500004)
#define TCON_REG __REG(0xE2500008)
#define TCNTB0_REG __REG(0xE250000c)
#define TCMPB0_REG __REG(0xE2500010)
#define TCNTO0_REG __REG(0xE2500014)
#define TCNTB1_REG __REG(0xE2500018)
#define TCMPB1_REG __REG(0xE250001c)
#define TCNTO1_REG __REG(0xE2500020)
#define TCNTB2_REG __REG(0xE2500024)
#define TCMPB2_REG __REG(0xE2500028)
#define TCNTO2_REG __REG(0xE250002c)
#define TCNTB3_REG __REG(0xE2500030)
#define TCMPB3_REG __REG(0xE2500034)
#define TCNTO3_REG __REG(0xE2500038)
#define TCNTB4_REG __REG(0xE250003c)
#define TCNTO4_REG __REG(0xE2500040)
#define TINT_CSTAT __REG(0xE2500044)/* Fields */
#define fTCFG0_DZONE Fld(8,16) /* the dead zone length (= timer 0) */
#define fTCFG0_PRE1 Fld(8,8) /* prescaler value for time 2,3,4 */
#define fTCFG0_PRE0 Fld(8,0) /* prescaler value for time 0,1 */
#define fTCFG1_MUX4 Fld(4,16)
/* bits */
#define TCFG0_DZONE(x) FInsrt((x), fTCFG0_DZONE)
#define TCFG0_PRE1(x) FInsrt((x), fTCFG0_PRE1)
#define TCFG0_PRE0(x) FInsrt((x), fTCFG0_PRE0)
#define TCON_4_AUTO (1 << 22) /* auto reload on/off for Timer 4 */
#define TCON_4_UPDATE (1 << 21) /* manual Update TCNTB4 */
#define TCON_4_ONOFF (1 << 20) /* 0: Stop, 1: start Timer 4 */
#define COUNT_4_ON (TCON_4_ONOFF*1)
#define COUNT_4_OFF (TCON_4_ONOFF*0)
#define TCON_3_AUTO (1 << 19) /* auto reload on/off for Timer 3 */
#define TIMER3_ATLOAD_ON (TCON_3_AUTO*1)
#define TIMER3_ATLAOD_OFF FClrBit(TCON, TCON_3_AUTO)
#define TCON_3_INVERT (1 << 18) /* 1: Inverter on for TOUT3 */
#define TIMER3_IVT_ON (TCON_3_INVERT*1)
#define TIMER3_IVT_OFF (FClrBit(TCON, TCON_3_INVERT))
#define TCON_3_MAN (1 << 17) /* manual Update TCNTB3,TCMPB3 */
#define TIMER3_MANUP (TCON_3_MAN*1)
#define TIMER3_NOP (FClrBit(TCON, TCON_3_MAN))
#define TCON_3_ONOFF (1 << 16) /* 0: Stop, 1: start Timer 3 */
#define TIMER3_ON (TCON_3_ONOFF*1)
#define TIMER3_OFF (FClrBit(TCON, TCON_3_ONOFF))
/* macros */
#define GET_PRESCALE_TIMER4(x) FExtr((x), fTCFG0_PRE1)
#define GET_DIVIDER_TIMER4(x) FExtr((x), fTCFG1_MUX4)#define MP01CON_OFFSET 0x2E0
#define MP01DAT_OFFSET 0x2E4
#define MP01PUD_OFFSET 0x2E8
#define MP01DRV_SR_OFFSET 0x2EC
#define MP01CONPDN_OFFSET 0x2E0
#define MP01PUDPDN_OFFSET 0x2E4#define MP02CON_OFFSET 0x300
#define MP02DAT_OFFSET 0x304
#define MP02PUD_OFFSET 0x308
#define MP02DRV_SR_OFFSET 0x30c
#define MP02CONPDN_OFFSET 0x310
#define MP02PUDPDN_OFFSET 0x314#define MP03CON_OFFSET 0x320
#define MP03DAT_OFFSET 0x324
#define MP03PUD_OFFSET 0x328
#define MP03DRV_SR_OFFSET 0x32c
#define MP03CONPDN_OFFSET 0x330
#define MP03PUDPDN_OFFSET 0x334#define MP06CON_OFFSET 0x380
#define MP06DAT_OFFSET 0x384
#define MP06PUD_OFFSET 0x388
#define MP06DRV_SR_OFFSET 0x38C
#define MP06CONPDN_OFFSET 0x390
#define MP06PUDPDN_OFFSET 0x394#define MP07CON_OFFSET 0x3A0
#define MP07DAT_OFFSET 0x3A4
#define MP07PUD_OFFSET 0x3A8
#define MP07DRV_SR_OFFSET 0x3AC
#define MP07CONPDN_OFFSET 0x3B0
#define MP07PUDPDN_OFFSET 0x3B4/** Nand flash controller*/
#define ELFIN_NAND_BASE 0xB0E00000
#define ELFIN_NAND_ECC_BASE 0xB0E20000#define NFCONF_OFFSET 0x00
#define NFCONT_OFFSET 0x04
#define NFCMMD_OFFSET 0x08
#define NFADDR_OFFSET 0x0c
#define NFDATA_OFFSET 0x10
#define NFMECCDATA0_OFFSET 0x14
#define NFMECCDATA1_OFFSET 0x18
#define NFSECCDATA0_OFFSET 0x1c
#define NFSBLK_OFFSET 0x20
#define NFEBLK_OFFSET 0x24
#define NFSTAT_OFFSET 0x28
#define NFESTAT0_OFFSET 0x2c
#define NFESTAT1_OFFSET 0x30
#define NFMECC0_OFFSET 0x34
#define NFMECC1_OFFSET 0x38
#define NFSECC_OFFSET 0x3c
#define NFMLCBITPT_OFFSET 0x40
#define NFECCCONF_OFFSET 0x000 // R/W ECC configuration register 0x0000_0000
#define NFECCCONT_OFFSET 0x020 // R/W ECC control register 0x0000_0000
#define NFECCSTAT_OFFSET 0x030 // R ECC status register 0x0000_0000
#define NFECCSECSTAT_OFFSET 0x040 // R ECC sector status register 0x0000_0000
#define NFECCPRGECC0_OFFSET 0x090 // R ECC parity code0 register for page program 0x0000_0000
#define NFECCPRGECC1_OFFSET 0x094 // R ECC parity code1 register for page program 0x0000_0000
#define NFECCPRGECC2_OFFSET 0x098 // R ECC parity code2 register for page program 0x0000_0000
#define NFECCPRGECC3_OFFSET 0x09C // R ECC parity code3 register for page program 0x0000_0000
#define NFECCPRGECC4_OFFSET 0x0A0 // R ECC parity code4 register for page program 0x0000_0000
#define NFECCPRGECC5_OFFSET 0x0A4 // R ECC parity code5 register for page program 0x0000_0000
#define NFECCPRGECC6_OFFSET 0x0A8 // R ECC parity code6 register for page program 0x0000_0000
#define NFECCERL0_OFFSET 0x0C0 // R ECC error byte location0 register 0x0000_0000
#define NFECCERL1_OFFSET 0x0C4 // R ECC error byte location1 register 0x0000_0000
#define NFECCERL2_OFFSET 0x0C8 // R ECC error byte location2 register 0x0000_0000
#define NFECCERL3_OFFSET 0x0CC // R ECC error byte location3 register 0x0000_0000
#define NFECCERL4_OFFSET 0x0D0 // R ECC error byte location4 register 0x0000_0000
#define NFECCERL5_OFFSET 0x0D4 // R ECC error byte location5 register 0x0000_0000
#define NFECCERL6_OFFSET 0x0D8 // R ECC error byte location6 register 0x0000_0000
#define NFECCERL7_OFFSET 0x0DC // R ECC error byte location7 register 0x0000_0000
#define NFECCERP0_OFFSET 0x0F0 // R ECC error bit pattern0 register 0x0000_0000
#define NFECCERP1_OFFSET 0x0F4 // R ECC error bit pattern1 register 0x0000_0000
#define NFECCERP2_OFFSET 0x0F8 // R ECC error bit pattern2 register 0x0000_0000
#define NFECCERP3_OFFSET 0x0FC // R ECC error bit pattern3 register 0x0000_0000
#define NFECCCONECC0_OFFSET 0x110 // R/W ECC parity conversion code0 register 0x0000_0000
#define NFECCCONECC1_OFFSET 0x114 // R/W ECC parity conversion code1 register 0x0000_0000
#define NFECCCONECC2_OFFSET 0x118 // R/W ECC parity conversion code2 register 0x0000_0000
#define NFECCCONECC3_OFFSET 0x11C // R/W ECC parity conversion code3 register 0x0000_0000
#define NFECCCONECC4_OFFSET 0x120 // R/W ECC parity conversion code4 register 0x0000_0000
#define NFECCCONECC5_OFFSET 0x124 // R/W ECC parity conversion code5 register 0x0000_0000
#define NFECCCONECC6_OFFSET 0x128 // R/W ECC parity conversion code6 register 0x0000_0000#define NFCONF (ELFIN_NAND_BASE+NFCONF_OFFSET)
#define NFCONT (ELFIN_NAND_BASE+NFCONT_OFFSET)
#define NFCMMD (ELFIN_NAND_BASE+NFCMMD_OFFSET)
#define NFADDR (ELFIN_NAND_BASE+NFADDR_OFFSET)
#define NFDATA (ELFIN_NAND_BASE+NFDATA_OFFSET)
#define NFMECCDATA0 (ELFIN_NAND_BASE+NFMECCDATA0_OFFSET)
#define NFMECCDATA1 (ELFIN_NAND_BASE+NFMECCDATA1_OFFSET)
#define NFSECCDATA0 (ELFIN_NAND_BASE+NFSECCDATA0_OFFSET)
#define NFSBLK (ELFIN_NAND_BASE+NFSBLK_OFFSET)
#define NFEBLK (ELFIN_NAND_BASE+NFEBLK_OFFSET)
#define NFSTAT (ELFIN_NAND_BASE+NFSTAT_OFFSET)
#define NFESTAT0 (ELFIN_NAND_BASE+NFESTAT0_OFFSET)
#define NFESTAT1 (ELFIN_NAND_BASE+NFESTAT1_OFFSET)
#define NFMECC0 (ELFIN_NAND_BASE+NFMECC0_OFFSET)
#define NFMECC1 (ELFIN_NAND_BASE+NFMECC1_OFFSET)
#define NFSECC (ELFIN_NAND_BASE+NFSECC_OFFSET)
#define NFMLCBITPT (ELFIN_NAND_BASE+NFMLCBITPT_OFFSET)#define NFECCCONF (ELFIN_NAND_ECC_BASE+NFECCCONF_OFFSET)
#define NFECCCONT (ELFIN_NAND_ECC_BASE+NFECCCONT_OFFSET)
#define NFECCSTAT (ELFIN_NAND_ECC_BASE+NFECCSTAT_OFFSET)
#define NFECCSECSTAT (ELFIN_NAND_ECC_BASE+NFECCSECSTAT_OFFSET)
#define NFECCPRGECC0 (ELFIN_NAND_ECC_BASE+NFECCPRGECC0_OFFSET)
#define NFECCPRGECC1 (ELFIN_NAND_ECC_BASE+NFECCPRGECC1_OFFSET)
#define NFECCPRGECC2 (ELFIN_NAND_ECC_BASE+NFECCPRGECC2_OFFSET)
#define NFECCPRGECC3 (ELFIN_NAND_ECC_BASE+NFECCPRGECC3_OFFSET)
#define NFECCPRGECC4 (ELFIN_NAND_ECC_BASE+NFECCPRGECC4_OFFSET)
#define NFECCPRGECC5 (ELFIN_NAND_ECC_BASE+NFECCPRGECC5_OFFSET)
#define NFECCPRGECC6 (ELFIN_NAND_ECC_BASE+NFECCPRGECC6_OFFSET)
#define NFECCERL0 (ELFIN_NAND_ECC_BASE+NFECCERL0_OFFSET)
#define NFECCERL1 (ELFIN_NAND_ECC_BASE+NFECCERL1_OFFSET)
#define NFECCERL2 (ELFIN_NAND_ECC_BASE+NFECCERL2_OFFSET)
#define NFECCERL3 (ELFIN_NAND_ECC_BASE+NFECCERL3_OFFSET)
#define NFECCERL4 (ELFIN_NAND_ECC_BASE+NFECCERL4_OFFSET)
#define NFECCERL5 (ELFIN_NAND_ECC_BASE+NFECCERL5_OFFSET)
#define NFECCERL6 (ELFIN_NAND_ECC_BASE+NFECCERL6_OFFSET)
#define NFECCERL7 (ELFIN_NAND_ECC_BASE+NFECCERL7_OFFSET)
#define NFECCERP0 (ELFIN_NAND_ECC_BASE+NFECCERP0_OFFSET)
#define NFECCERP1 (ELFIN_NAND_ECC_BASE+NFECCERP1_OFFSET)
#define NFECCERP2 (ELFIN_NAND_ECC_BASE+NFECCERP2_OFFSET)
#define NFECCERP3 (ELFIN_NAND_ECC_BASE+NFECCERP3_OFFSET)
#define NFECCCONECC0 (ELFIN_NAND_ECC_BASE+NFECCCONECC0_OFFSET)
#define NFECCCONECC1 (ELFIN_NAND_ECC_BASE+NFECCCONECC1_OFFSET)
#define NFECCCONECC2 (ELFIN_NAND_ECC_BASE+NFECCCONECC2_OFFSET)
#define NFECCCONECC3 (ELFIN_NAND_ECC_BASE+NFECCCONECC3_OFFSET)
#define NFECCCONECC4 (ELFIN_NAND_ECC_BASE+NFECCCONECC4_OFFSET)
#define NFECCCONECC5 (ELFIN_NAND_ECC_BASE+NFECCCONECC5_OFFSET)
#define NFECCCONECC6 (ELFIN_NAND_ECC_BASE+NFECCCONECC6_OFFSET)#define NFCONF_REG __REG(ELFIN_NAND_BASE+NFCONF_OFFSET)
#define NFCONT_REG __REG(ELFIN_NAND_BASE+NFCONT_OFFSET)
#define NFCMD_REG __REG(ELFIN_NAND_BASE+NFCMMD_OFFSET)
#define NFADDR_REG __REG(ELFIN_NAND_BASE+NFADDR_OFFSET)
#define NFDATA_REG __REG(ELFIN_NAND_BASE+NFDATA_OFFSET)
#define NFDATA8_REG __REGb(ELFIN_NAND_BASE+NFDATA_OFFSET)
#define NFMECCDATA0_REG __REG(ELFIN_NAND_BASE+NFMECCDATA0_OFFSET)
#define NFMECCDATA1_REG __REG(ELFIN_NAND_BASE+NFMECCDATA1_OFFSET)
#define NFSECCDATA0_REG __REG(ELFIN_NAND_BASE+NFSECCDATA0_OFFSET)
#define NFSBLK_REG __REG(ELFIN_NAND_BASE+NFSBLK_OFFSET)
#define NFEBLK_REG __REG(ELFIN_NAND_BASE+NFEBLK_OFFSET)
#define NFSTAT_REG __REG(ELFIN_NAND_BASE+NFSTAT_OFFSET)
#define NFESTAT0_REG __REG(ELFIN_NAND_BASE+NFESTAT0_OFFSET)
#define NFESTAT1_REG __REG(ELFIN_NAND_BASE+NFESTAT1_OFFSET)
#define NFMECC0_REG __REG(ELFIN_NAND_BASE+NFMECC0_OFFSET)
#define NFMECC1_REG __REG(ELFIN_NAND_BASE+NFMECC1_OFFSET)
#define NFSECC_REG __REG(ELFIN_NAND_BASE+NFSECC_OFFSET)
#define NFMLCBITPT_REG __REG(ELFIN_NAND_BASE+NFMLCBITPT_OFFSET)#define NFCONF_ECC_MLC (1<<24)#define NFCONF_ECC_1BIT (0<<23)
#define NFCONF_ECC_4BIT (2<<23)
#define NFCONF_ECC_8BIT (1<<23)#define NFCONT_ECC_ENC (1<<18)
#define NFCONT_WP (1<<16)
#define NFCONT_MECCLOCK (1<<7)
#define NFCONT_SECCLOCK (1<<6)
#define NFCONT_INITMECC (1<<5)
#define NFCONT_INITSECC (1<<4)
#define NFCONT_INITECC (NFCONT_INITMECC | NFCONT_INITSECC)
#define NFCONT_CS (1<<1)
#define NFSTAT_ECCENCDONE (1<<25)
#define NFSTAT_ECCDECDONE (1<<24)
#define NFSTAT_RnB (1<<0)
#define NFESTAT0_ECCBUSY (1<<31)/* Access Controller (TZPC) */
#define TZPC_DECPROT0SET_OFFSET 0x804
#define TZPC_DECPROT1SET_OFFSET 0x810
#define TZPC_DECPROT2SET_OFFSET 0x81C
#define TZPC_DECPROT3SET_OFFSET 0x828/************************************************************** OneNAND Controller*************************************************************/
#define ELFIN_ONENAND_BASE 0xB0000000
#define ELFIN_ONENANDCON_BASE (ELFIN_ONENAND_BASE + 0x600000)#define ONENAND_IF_CTRL_OFFSET 0x100
#define ONENAND_IF_CMD_OFFSET 0x104
#define ONENAND_IF_ASYNC_TIMING_CTRL_OFFSET 0x108
#define ONENAND_IF_STATUS_OFFSET 0x10C
#define DMA_SRC_ADDR_OFFSET 0x400
#define DMA_SRC_CFG_OFFSET 0x404
#define DMA_DST_ADDR_OFFSET 0x408
#define DMA_DST_CFG_OFFSET 0x40C
#define DMA_TRANS_SIZE_OFFSET 0x414
#define DMA_TRANS_CMD_OFFSET 0x418
#define DMA_TRANS_STATUS_OFFSET 0x41C
#define DMA_TRANS_DIR_OFFSET 0x420
#define SQC_SAO_OFFSET 0x600
#define SQC_CMD_OFFSET 0x608
#define SQC_STATUS_OFFSET 0x60C
#define SQC_CAO_OFFSET 0x610
#define SQC_REG_CTRL_OFFSET 0x614
#define SQC_REG_VAL_OFFSET 0x618
#define SQC_BRPAO0_OFFSET 0x620
#define SQC_BRPAO1_OFFSET 0x624
#define INTC_SQC_CLR_OFFSET 0x1000
#define INTC_DMA_CLR_OFFSET 0x1004
#define INTC_ONENAND_CLR_OFFSET 0x1008
#define INTC_SQC_MASK_OFFSET 0x1020
#define INTC_DMA_MASK_OFFSET 0x1024
#define INTC_ONENAND_MASK_OFFSET 0x1028
#define INTC_SQC_PEND_OFFSET 0x1040
#define INTC_DMA_PEND_OFFSET 0x1044
#define INTC_ONENAND_PEND_OFFSET 0x1048
#define INTC_SQC_STATUS_OFFSET 0x1060
#define INTC_DMA_STATUS_OFFSET 0x1064
#define INTC_ONENAND_STATUS_OFFSET 0x1068/** Memory controller*/
#define ELFIN_SROM_BASE 0xE8000000#define SROM_BW_REG __REG(ELFIN_SROM_BASE+0x0)
#define SROM_BC0_REG __REG(ELFIN_SROM_BASE+0x4)
#define SROM_BC1_REG __REG(ELFIN_SROM_BASE+0x8)
#define SROM_BC2_REG __REG(ELFIN_SROM_BASE+0xC)
#define SROM_BC3_REG __REG(ELFIN_SROM_BASE+0x10)
#define SROM_BC4_REG __REG(ELFIN_SROM_BASE+0x14)
#define SROM_BC5_REG __REG(ELFIN_SROM_BASE+0x18)/** SDRAM Controller*/
#define APB_DMC_0_BASE 0xF0000000
#define APB_DMC_1_BASE 0xF1400000
#define ASYNC_MSYS_DMC0_BASE 0xF1E00000#define DMC_CONCONTROL 0x00
#define DMC_MEMCONTROL 0x04
#define DMC_MEMCONFIG0 0x08
#define DMC_MEMCONFIG1 0x0C
#define DMC_DIRECTCMD 0x10
#define DMC_PRECHCONFIG 0x14
#define DMC_PHYCONTROL0 0x18
#define DMC_PHYCONTROL1 0x1C
#define DMC_RESERVED 0x20
#define DMC_PWRDNCONFIG 0x28
#define DMC_TIMINGAREF 0x30
#define DMC_TIMINGROW 0x34
#define DMC_TIMINGDATA 0x38
#define DMC_TIMINGPOWER 0x3C
#define DMC_PHYSTATUS 0x40
#define DMC_CHIP0STATUS 0x48
#define DMC_CHIP1STATUS 0x4C
#define DMC_AREFSTATUS 0x50
#define DMC_MRSTATUS 0x54
#define DMC_PHYTEST0 0x58
#define DMC_PHYTEST1 0x5C
#define DMC_QOSCONTROL0 0x60
#define DMC_QOSCONFIG0 0x64
#define DMC_QOSCONTROL1 0x68
#define DMC_QOSCONFIG1 0x6C
#define DMC_QOSCONTROL2 0x70
#define DMC_QOSCONFIG2 0x74
#define DMC_QOSCONTROL3 0x78
#define DMC_QOSCONFIG3 0x7C
#define DMC_QOSCONTROL4 0x80
#define DMC_QOSCONFIG4 0x84
#define DMC_QOSCONTROL5 0x88
#define DMC_QOSCONFIG5 0x8C
#define DMC_QOSCONTROL6 0x90
#define DMC_QOSCONFIG6 0x94
#define DMC_QOSCONTROL7 0x98
#define DMC_QOSCONFIG7 0x9C
#define DMC_QOSCONTROL8 0xA0
#define DMC_QOSCONFIG8 0xA4
#define DMC_QOSCONTROL9 0xA8
#define DMC_QOSCONFIG9 0xAC
#define DMC_QOSCONTROL10 0xB0
#define DMC_QOSCONFIG10 0xB4
#define DMC_QOSCONTROL11 0xB8
#define DMC_QOSCONFIG11 0xBC
#define DMC_QOSCONTROL12 0xC0
#define DMC_QOSCONFIG12 0xC4
#define DMC_QOSCONTROL13 0xC8
#define DMC_QOSCONFIG13 0xCC
#define DMC_QOSCONTROL14 0xD0
#define DMC_QOSCONFIG14 0xD4
#define DMC_QOSCONTROL15 0xD8
#define DMC_QOSCONFIG15 0xDC/*
* Memory Chip direct command
*//****************************************************************Definitions for memory configurationSet memory configurationactive_chips = 1'b0 (1 chip)qos_master_chip = 3'b000(ARID[3:0])memory burst = 3'b010(burst 4)stop_mem_clock = 1'b0(disable dynamical stop)auto_power_down = 1'b0(disable auto power-down mode)power_down_prd = 6'b00_0000(0 cycle for auto power-down)ap_bit = 1'b0 (bit position of auto-precharge is 10)row_bits = 3'b010(# row address 13)column_bits = 3'b010(# column address 10 )Set user configuration2'b10=SDRAM/mSDRAM, 2'b11=DDR, 2'b01=mDDRSet chip select for chip [n]row bank control, bank address 0x3000_0000 ~ 0x37ff_ffffCHIP_[n]_CFG=0x30F8, 30: ADDR[31:24], F8: Mask[31:24]
******************************************************************/#define INF_REG_BASE 0xE010F000#define INF_REG0_REG __REG(INF_REG_BASE+INF_REG0_OFFSET)
#define INF_REG1_REG __REG(INF_REG_BASE+INF_REG1_OFFSET)
#define INF_REG2_REG __REG(INF_REG_BASE+INF_REG2_OFFSET)
#define INF_REG3_REG __REG(INF_REG_BASE+INF_REG3_OFFSET)
#define INF_REG4_REG __REG(INF_REG_BASE+INF_REG4_OFFSET)
#define INF_REG5_REG __REG(INF_REG_BASE+INF_REG5_OFFSET)
#define INF_REG6_REG __REG(INF_REG_BASE+INF_REG6_OFFSET)
#define INF_REG7_REG __REG(INF_REG_BASE+INF_REG7_OFFSET)#define NFCONF_VAL (7<<12)|(7<<8)|(7<<4)|(0<<3)|(0<<2)|(1<<1)|(0<<0)
#define NFCONT_VAL (0x1<<23)|(0x1<<22)|(0<<18)|(0<<17)|(0<<16)|(0<<10)|(0<<9)|(0<<8)|(0<<7)|(0<<6)|(0x2<<1)|(1<<0)
#define MP03CON_VAL (1<<29)|(1<<25)|(1<<21)|(1<<17)|(1<<13)|(1<<9)|(1<<5)|(1<<1)#define ELFIN_TZPC0_BASE 0xF1500000
#define ELFIN_TZPC1_BASE 0xFAD00000
#define ELFIN_TZPC2_BASE 0xE0600000
#define ELFIN_TZPC3_BASE 0xE1C00000sdram_init.S
#include "s5pv210.h"#if 1
#define DMC0_MEMCONTROL 0x00202400 // MemControl BL=4, 1Chip, DDR2 Type, dynamic self refresh, force precharge, dynamic power down off#define DMC0_MEMCONFIG_0 0x20F01323 // MemConfig0 256MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
#define DMC0_MEMCONFIG_1 0x30F00312 // MemConfig1 默认值#define DMC0_TIMINGA_REF 0x00000618 // TimingAref 7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4E)
#define DMC0_TIMING_ROW 0x28233287 // TimingRow for @200MHz
#define DMC0_TIMING_DATA 0x23240304 // TimingData CL=3
#define DMC0_TIMING_PWR 0x09C80232 // TimingPower#define DMC1_MEMCONTROL 0x00202400 // MemControl BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off#define DMC1_MEMCONFIG_0 0x40F01323 // MemConfig0 512MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
#define DMC1_MEMCONFIG_1 0x60E00312 // MemConfig1#define DMC1_TIMINGA_REF 0x00000618 // TimingAref 7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4
#define DMC1_TIMING_ROW 0x28233289 // TimingRow for @200MHz
#define DMC1_TIMING_DATA 0x23240304 // TimingData CL=3
#define DMC1_TIMING_PWR 0x08280232 // TimingPower#endif#if 0#define DMC0_MEMCONTROL 0x00212400 // MemControl BL=4, 1Chip, DDR2 Type, dynamic self refresh, force precharge, dynamic power down off#define DMC0_MEMCONFIG_0 0x20E01323 // MemConfig0 512MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
#define DMC0_MEMCONFIG_1 0x40F01323 // MemConfig1#define DMC0_TIMINGA_REF 0x00000618 // TimingAref 7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4E)
#define DMC0_TIMING_ROW 0x28233287 // TimingRow for @200MHz
#define DMC0_TIMING_DATA 0x23240304 // TimingData CL=3
#define DMC0_TIMING_PWR 0x09C80232 // TimingPower#define DMC1_MEMCONTROL 0x00202400 // MemControl BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off#define DMC1_MEMCONFIG_0 0x40C01323 // MemConfig0 512MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
#define DMC1_MEMCONFIG_1 0x00E01323 // MemConfig1#define DMC1_TIMINGA_REF 0x00000618 // TimingAref 7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4
#define DMC1_TIMING_ROW 0x28233289 // TimingRow for @200MHz
#define DMC1_TIMING_DATA 0x23240304 // TimingData CL=3
#define DMC1_TIMING_PWR 0x08280232 // TimingPower#endif.global sdram_asm_initsdram_asm_init:ldr r0, =0xf1e00000ldr r1, =0x0str r1, [r0, #0x0]/* DMC0 Drive Strength (Setting 2X) */ldr r0, =ELFIN_GPIO_BASEldr r1, =0x0000AAAAstr r1, [r0, #MP1_0DRV_SR_OFFSET] // 寄存器中对应0b10，就是2Xldr r1, =0x0000AAAAstr r1, [r0, #MP1_1DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP1_2DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP1_3DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP1_4DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP1_5DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP1_6DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP1_7DRV_SR_OFFSET]ldr r1, =0x00002AAAstr r1, [r0, #MP1_8DRV_SR_OFFSET]/* DMC1 Drive Strength (Setting 2X) */ldr r0, =ELFIN_GPIO_BASEldr r1, =0x0000AAAAstr r1, [r0, #MP2_0DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP2_1DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP2_2DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP2_3DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP2_4DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP2_5DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP2_6DRV_SR_OFFSET]ldr r1, =0x0000AAAAstr r1, [r0, #MP2_7DRV_SR_OFFSET]ldr r1, =0x00002AAAstr r1, [r0, #MP2_8DRV_SR_OFFSET]/* DMC0 initialization at single Type*/ldr r0, =APB_DMC_0_BASEldr r1, =0x00101000 @PhyControl0 DLL parameter setting, manual 0x00101000str r1, [r0, #DMC_PHYCONTROL0]ldr r1, =0x00000086 @PhyControl1 DLL parameter setting, LPDDR/LPDDR2 Casestr r1, [r0, #DMC_PHYCONTROL1]ldr r1, =0x00101002 @PhyControl0 DLL onstr r1, [r0, #DMC_PHYCONTROL0]ldr r1, =0x00101003 @PhyControl0 DLL startstr r1, [r0, #DMC_PHYCONTROL0]find_lock_val:ldr r1, [r0, #DMC_PHYSTATUS] @Load Phystatus register valueand r2, r1, #0x7cmp r2, #0x7 @Loop until DLL is lockedbne find_lock_valand r1, #0x3fc0 mov r2, r1, LSL #18orr r2, r2, #0x100000orr r2 ,r2, #0x1000orr r1, r2, #0x3 @Force Value lockingstr r1, [r0, #DMC_PHYCONTROL0]#if 0 /* Memory margin test 10.01.05 */orr r1, r2, #0x1 @DLL offstr r1, [r0, #DMC_PHYCONTROL0]
#endif/* setting DDR2 */ldr r1, =0x0FFF2010 @ConControl auto refresh offstr r1, [r0, #DMC_CONCONTROL]ldr r1, =DMC0_MEMCONTROL @MemControl BL=4, 1 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down offstr r1, [r0, #DMC_MEMCONTROL]ldr r1, =DMC0_MEMCONFIG_0 @MemConfig0 256MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixedstr r1, [r0, #DMC_MEMCONFIG0]ldr r1, =DMC0_MEMCONFIG_1 @MemConfig1str r1, [r0, #DMC_MEMCONFIG1]ldr r1, =0xFF000000 @PrechConfigstr r1, [r0, #DMC_PRECHCONFIG]ldr r1, =DMC0_TIMINGA_REF @TimingAref 7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4E)str r1, [r0, #DMC_TIMINGAREF]ldr r1, =DMC0_TIMING_ROW @TimingRow for @200MHzstr r1, [r0, #DMC_TIMINGROW]ldr r1, =DMC0_TIMING_DATA @TimingData CL=3str r1, [r0, #DMC_TIMINGDATA]ldr r1, =DMC0_TIMING_PWR @TimingPowerstr r1, [r0, #DMC_TIMINGPOWER]ldr r1, =0x07000000 @DirectCmd chip0 Deselectstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01000000 @DirectCmd chip0 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00020000 @DirectCmd chip0 EMRS2str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00030000 @DirectCmd chip0 EMRS3str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00010400 @DirectCmd chip0 EMRS1 (MEM DLL on, DQS# disable)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00000542 @DirectCmd chip0 MRS (MEM DLL reset) CL=4, BL=4str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01000000 @DirectCmd chip0 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05000000 @DirectCmd chip0 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05000000 @DirectCmd chip0 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00000442 @DirectCmd chip0 MRS (MEM DLL unreset)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00010780 @DirectCmd chip0 EMRS1 (OCD default)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00010400 @DirectCmd chip0 EMRS1 (OCD exit)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x07100000 @DirectCmd chip1 Deselectstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01100000 @DirectCmd chip1 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00120000 @DirectCmd chip1 EMRS2str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00130000 @DirectCmd chip1 EMRS3str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00110400 @DirectCmd chip1 EMRS1 (MEM DLL on, DQS# disable)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00100542 @DirectCmd chip1 MRS (MEM DLL reset) CL=4, BL=4str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01100000 @DirectCmd chip1 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05100000 @DirectCmd chip1 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05100000 @DirectCmd chip1 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00100442 @DirectCmd chip1 MRS (MEM DLL unreset)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00110780 @DirectCmd chip1 EMRS1 (OCD default)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00110400 @DirectCmd chip1 EMRS1 (OCD exit)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x0FF02030 @ConControl auto refresh onstr r1, [r0, #DMC_CONCONTROL]ldr r1, =0xFFFF00FF @PwrdnConfigstr r1, [r0, #DMC_PWRDNCONFIG]ldr r1, =0x00202400 @MemControl BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down offstr r1, [r0, #DMC_MEMCONTROL]// 上面是DRAM0初始化步骤
/*******************************************************************************************/
// 下面是DRAM1初始化步骤，两者没有联系，是并列的。/* DMC1 initialization */ldr r0, =APB_DMC_1_BASEldr r1, =0x00101000 @Phycontrol0 DLL parameter settingstr r1, [r0, #DMC_PHYCONTROL0]ldr r1, =0x00000086 @Phycontrol1 DLL parameter settingstr r1, [r0, #DMC_PHYCONTROL1]ldr r1, =0x00101002 @PhyControl0 DLL onstr r1, [r0, #DMC_PHYCONTROL0]ldr r1, =0x00101003 @PhyControl0 DLL startstr r1, [r0, #DMC_PHYCONTROL0]find_lock_val1:ldr r1, [r0, #DMC_PHYSTATUS] @Load Phystatus register valueand r2, r1, #0x7cmp r2, #0x7 @Loop until DLL is lockedbne find_lock_val1and r1, #0x3fc0 mov r2, r1, LSL #18orr r2, r2, #0x100000orr r2, r2, #0x1000orr r1, r2, #0x3 @Force Value lockingstr r1, [r0, #DMC_PHYCONTROL0]#if 0 /* Memory margin test 10.01.05 */orr r1, r2, #0x1 @DLL offstr r1, [r0, #DMC_PHYCONTROL0]
#endif/* settinf fot DDR2 */ldr r0, =APB_DMC_1_BASEldr r1, =0x0FFF2010 @auto refresh offstr r1, [r0, #DMC_CONCONTROL]ldr r1, =DMC1_MEMCONTROL @MemControl BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down offstr r1, [r0, #DMC_MEMCONTROL]ldr r1, =DMC1_MEMCONFIG_0 @MemConfig0 512MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixedstr r1, [r0, #DMC_MEMCONFIG0]ldr r1, =DMC1_MEMCONFIG_1 @MemConfig1str r1, [r0, #DMC_MEMCONFIG1]ldr r1, =0xFF000000str r1, [r0, #DMC_PRECHCONFIG]ldr r1, =DMC1_TIMINGA_REF @TimingAref 7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4str r1, [r0, #DMC_TIMINGAREF]ldr r1, =DMC1_TIMING_ROW @TimingRow for @200MHzstr r1, [r0, #DMC_TIMINGROW]ldr r1, =DMC1_TIMING_DATA @TimingData CL=3str r1, [r0, #DMC_TIMINGDATA]ldr r1, =DMC1_TIMING_PWR @TimingPowerstr r1, [r0, #DMC_TIMINGPOWER]ldr r1, =0x07000000 @DirectCmd chip0 Deselectstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01000000 @DirectCmd chip0 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00020000 @DirectCmd chip0 EMRS2str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00030000 @DirectCmd chip0 EMRS3str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00010400 @DirectCmd chip0 EMRS1 (MEM DLL on, DQS# disable)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00000542 @DirectCmd chip0 MRS (MEM DLL reset) CL=4, BL=4str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01000000 @DirectCmd chip0 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05000000 @DirectCmd chip0 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05000000 @DirectCmd chip0 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00000442 @DirectCmd chip0 MRS (MEM DLL unreset)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00010780 @DirectCmd chip0 EMRS1 (OCD default)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00010400 @DirectCmd chip0 EMRS1 (OCD exit)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x07100000 @DirectCmd chip1 Deselectstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01100000 @DirectCmd chip1 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00120000 @DirectCmd chip1 EMRS2str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00130000 @DirectCmd chip1 EMRS3str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00110440 @DirectCmd chip1 EMRS1 (MEM DLL on, DQS# disable)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00100542 @DirectCmd chip1 MRS (MEM DLL reset) CL=4, BL=4str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x01100000 @DirectCmd chip1 PALLstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05100000 @DirectCmd chip1 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x05100000 @DirectCmd chip1 REFAstr r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00100442 @DirectCmd chip1 MRS (MEM DLL unreset)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00110780 @DirectCmd chip1 EMRS1 (OCD default)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x00110400 @DirectCmd chip1 EMRS1 (OCD exit)str r1, [r0, #DMC_DIRECTCMD]ldr r1, =0x0FF02030 @ConControl auto refresh onstr r1, [r0, #DMC_CONCONTROL]ldr r1, =0xFFFF00FF @PwrdnConfigstr r1, [r0, #DMC_PWRDNCONFIG]ldr r1, =DMC1_MEMCONTROL @MemControl BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down offstr r1, [r0, #DMC_MEMCONTROL]// 函数返回mov pc, lrload_sd_bl2_2_ddr.c
#define CHANNEL 2
#define SD_START_BLOCK 45
#define SD_BLOCK_COUNT (2048*2)
#define DDR_START_ADDR 0x23E00000
#define WITH_INIT 0typedef unsigned int bool;typedef bool(*copy_sdmmc_to_mem)(int, unsigned int, unsigned short, unsigned int*, bool);typedef void (*bl2_type)();void copy_bl2_2_ddr()
{//the func is copy bl2 to ddr//0xD0037F98 is the address of cpoy func //define func copy_sdmmc_to_mem copy = (copy_sdmmc_to_mem) (*((unsigned int *)0xD0037F98));//use funccopy(CHANNEL, SD_START_BLOCK, SD_BLOCK_COUNT, (unsigned int *)DDR_START_ADDR,WITH_INIT);//jump ddr,work bl2bl2_type bl2 = (bl2_type) DDR_START_ADDR;bl2();
}link.lds
SECTIONS
{. = 0xd0020010;.text : {start.o* (.text)}.data : {* (.data)}.bss : {* (.bss)}
}Makefile
CC = arm-linux-gcc
LD = arm-linux-ld
OBJCOPY = arm-linux-objcopy
OBJDUMP = arm-linux-objdumpINCDIR := $(shell pwd)#预处理器的flag，flag就是编译器可选的选项
CPPFLAGS := -nostdlib -nostdinc -I$(INCDIR)/include
#C编译器的flag
CFLAGS := -Wall -O2 -fno-builtinexport CC LD OBJCOPY OBJDUMP CPPFLAGS CFLAGSobjs := start.o load_sd_bl2_2_ddr.o sdram_init.o bl1.bin:$(objs)$(LD) -Tlink.lds -o bl1.elf $^$(OBJCOPY) -O binary bl1.elf bl1.bin$(OBJDUMP) -D bl1.elf > bl1.disgcc mkv210.c -o mkv210./mkv210 bl1.bin sd1.bin%.o:%.S$(CC) $(CPPFLAGS) $(CFLAGS) -o $@ $< -c%.o:%.c$(CC) $(CPPFLAGS) $(CFLAGS) -o $@ $< -cclean:rm *.o *.elf *.bin *.dis mkv210 -fbl2:
start.S
.global _start
_start:ldr pc,=mainb .main.c
#include "lcd.h"
#include "1024600.h"int main()
{lcd_init();//init_background(WHITE);//lcd_draw_line(0, 479, 799, 0, BLACK);//lcd_draw_circle(300, 500, 30, BLACK);//lcd_draw_string(0, 0, BLACK, "Hello Word !");lcd_appear_picture(gImage_1024600);return 0;
}lcd.h
#define BLUE 0x0000FF
#define RED 0xFF0000
#define GREEN 0x00FF00
#define WHITE 0xFFFFFF
#define BLACK 0x000000void lcd_init();void init_background(unsigned int color);void lcd_draw_line(unsigned int x1, unsigned int y1, unsigned int x2, unsigned int y2, unsigned int color);void lcd_draw_circle(unsigned int centerX, unsigned int centerY, unsigned int radius, unsigned int color);void lcd_draw_string(unsigned int x, unsigned int y, unsigned int color, unsigned char *str);void lcd_appear_picture(const unsigned char *pData);lcd.c
#include "ascii.h"typedef unsigned int u32;
typedef unsigned short u16;#define GPF0CON 0xE0200120
#define GPF1CON 0xE0200140
#define GPF2CON 0xE0200160
#define GPF3CON 0xE0200180#define GPD0CON 0xE02000A0
#define GPD0DAT 0xE02000A4#define rGPF0CON (*(volatile unsigned int *)GPF0CON)
#define rGPF1CON (*(volatile unsigned int *)GPF1CON)
#define rGPF2CON (*(volatile unsigned int *)GPF2CON)
#define rGPF3CON (*(volatile unsigned int *)GPF3CON)
#define rGPD0CON (*(volatile unsigned int *)GPD0CON)
#define rGPD0DAT (*(volatile unsigned int *)GPD0DAT)#define DISPLAY_CONTROL 0xe0107008
#define VIDCON0 0xF8000000
#define VIDCON1 0xF8000004
#define VIDTCON0 0xF8000010
#define VIDTCON1 0xF8000014
#define VIDTCON2 0xF8000018
#define WINCON0 0xF8000020
#define SHADOWCON 0xF8000034
#define VIDOSD0A 0xF8000040
#define VIDOSD0B 0xF8000044
#define VIDOSD0C 0xF8000048
#define VIDW00ADD0B0 0xF80000A0
#define VIDW00ADD1B0 0xF80000D0#define rDISPLAY_CONTROL (*(volatile unsigned int *)DISPLAY_CONTROL)
#define rVIDCON0 (*(volatile unsigned int *)VIDCON0)
#define rVIDCON1 (*(volatile unsigned int *)VIDCON1)
#define rVIDTCON0 (*(volatile unsigned int *)VIDTCON0)
#define rVIDTCON1 (*(volatile unsigned int *)VIDTCON1)
#define rVIDTCON2 (*(volatile unsigned int *)VIDTCON2)
#define rWINCON0 (*(volatile unsigned int *)WINCON0)
#define rSHADOWCON (*(volatile unsigned int *)SHADOWCON)
#define rVIDOSD0A (*(volatile unsigned int *)VIDOSD0A)
#define rVIDOSD0B (*(volatile unsigned int *)VIDOSD0B)
#define rVIDOSD0C (*(volatile unsigned int *)VIDOSD0C)
#define rVIDW00ADD0B0 (*(volatile unsigned int *)VIDW00ADD0B0)
#define rVIDW00ADD1B0 (*(volatile unsigned int *)VIDW00ADD1B0) #define HSPW (40)
#define HBPD (10 - 1)
#define HFPD (240 - 1)
#define VSPW (20)
#define VBPD (10 - 1)
#define VFPD (30 - 1)//FB地址
#define FB_ADDR (0x23000000)
#define ROW (600)
#define COL (1024)
#define HOZVAL (COL-1)
#define LINEVAL (ROW-1)#define XSIZE COL
#define YSIZE ROW#define LeftTopX 0
#define LeftTopY 0
#define RightBotX (1024 - 1)
#define RightBotY (600 - 1)u32 *pfb = (u32 *)FB_ADDR;void lcd_init()
{//set gpio as lcdrGPF0CON = 0x22222222;rGPF1CON = 0x22222222;rGPF2CON = 0x22222222;rGPF3CON = 0x22222222;//set gpio as PWMTOUT0, open background lightrGPD0CON &= ~(0xf);rGPD0CON |= (1);rGPD0DAT &= ~(1);//set lcd crontol(FIMD) connect outer port(180,rgb,yuv)rDISPLAY_CONTROL = 2;//rDISPLAY_CONTROL = 3;//set RGB interface,RGB parallel format,HCLK_DSYS(166MHz)rVIDCON0 &= ~((3<<26)|(1<<18)|(1<<2));//enable lcdrVIDCON0 |= ((1)|(1<<1));//set div(VCLK = 166Mhz/(4+1) = 33Mhz) and select divrVIDCON0 |= ((4<<6) | (1<<4));//set IVSYNC and IHSYNC high level(Inverted)rVIDCON1 |= ((1<<5) | (1<<6));//set Time sequencerVIDTCON0 = VBPD<<16 | VFPD<<8 | VSPW<<0;rVIDTCON1 = HBPD<<16 | HFPD<<8 | HSPW<<0;//set lcd width and length rVIDTCON2 = ((LINEVAL << 11) | (HOZVAL << 0));//enable window0 and set 24bpp(RGB888)rWINCON0 |= 1;rWINCON0 &= ~(0xf << 2);rWINCON0 |= (0xB<<2) | (1<<15);//set lcd coordinate and rangerVIDOSD0A = ((LeftTopX<<11) | (LeftTopY << 0));rVIDOSD0B = ((RightBotX<<11) | (RightBotY << 0));rVIDOSD0C = ((LINEVAL + 1) * (HOZVAL + 1));//set Video frame start and end address(buffer)rVIDW00ADD0B0 = FB_ADDR;rVIDW00ADD1B0 = (((HOZVAL + 1)*4 + 0) * (LINEVAL + 1)) & (0xffffff);//enable channel 0 to transmit datarSHADOWCON = 0x1;
}//set pic color
static void lcd_draw_pic_color(u32 x,u32 y,u32 color)
{*(pfb + COL * y + x) = color;
}//init lcd background
void init_background(unsigned int color)
{u32 i, j;for (j=0; j<ROW; j++){for (i=0; i<COL; i++){lcd_draw_pic_color(i, j, color);}}
}//glib draw line,dot_1(x1,y1),dot_2(x2,y2)
void lcd_draw_line(unsigned int x1, unsigned int y1, unsigned int x2, unsigned int y2, unsigned int color)
{int dx,dy,e;dx=x2-x1; dy=y2-y1;if(dx>=0){if(dy >= 0) // dy>=0{if(dx>=dy) // 1/8 octant{e=dy-dx/2; while(x1<=x2){lcd_draw_pic_color(x1,y1,color);if(e>0){y1+=1;e-=dx;}x1+=1;e+=dy;}}else // 2/8 octant{e=dx-dy/2;while(y1<=y2){lcd_draw_pic_color(x1,y1,color);if(e>0){x1+=1;e-=dy;}y1+=1;e+=dx;}}}else // dy<0{dy=-dy; // dy=abs(dy)if(dx>=dy) // 8/8 octant{e=dy-dx/2;while(x1<=x2){lcd_draw_pic_color(x1,y1,color);if(e>0){y1-=1;e-=dx;}x1+=1;e+=dy;}}else // 7/8 octant{e=dx-dy/2;while(y1>=y2){lcd_draw_pic_color(x1,y1,color);if(e>0){x1+=1;e-=dy;}y1-=1;e+=dx;}}}}else //dx<0{dx=-dx; //dx=abs(dx)if(dy >= 0) // dy>=0{if(dx>=dy) // 4/8 octant{e=dy-dx/2;while(x1>=x2){lcd_draw_pic_color(x1,y1,color);if(e>0){y1+=1;e-=dx;}x1-=1;e+=dy;}}else // 3/8 octant{e=dx-dy/2;while(y1<=y2){lcd_draw_pic_color(x1,y1,color);if(e>0){x1-=1;e-=dy;}y1+=1;e+=dx;}}}else // dy<0{dy=-dy; // dy=abs(dy)if(dx>=dy) // 5/8 octant{e=dy-dx/2;while(x1>=x2){lcd_draw_pic_color(x1,y1,color);if(e>0){y1-=1;e-=dx;}x1-=1;e+=dy;}}else // 6/8 octant{e=dx-dy/2;while(y1>=y2){lcd_draw_pic_color(x1,y1,color);if(e>0){x1-=1;e-=dy;}y1-=1;e+=dx;}}}}
}//draw circle , Center of a circle (centerX, centerY),radius,color
void lcd_draw_circle(unsigned int centerX, unsigned int centerY, unsigned int radius, unsigned int color)
{int x,y ;int tempX,tempY;;int SquareOfR = radius*radius;for(y=0; y<XSIZE; y++){for(x=0; x<YSIZE; x++){if(y<=centerY && x<=centerX){tempY=centerY-y;tempX=centerX-x; }else if(y<=centerY&& x>=centerX){tempY=centerY-y;tempX=x-centerX; }else if(y>=centerY&& x<=centerX){tempY=y-centerY;tempX=centerX-x; }else{tempY = y-centerY;tempX = x-centerX;}if ((tempY*tempY+tempX*tempX)<=SquareOfR)lcd_draw_pic_color(x, y, color);}}
}//draw letter,posion (x, y),color,data(Font information)
static void show_8_16(unsigned int x, unsigned int y, unsigned int color, unsigned char *data)
{ //count:recodes pix that usingint i, j, count = 0; for (j=y; j<(y+16); j++) { for (i=x; i<(x+8); i++) { if (i<XSIZE && j<YSIZE) { if (data[count/8] & (1<<(count%8))) lcd_draw_pic_color(i, j, color);} count++; } }
} //draw string,start posion(x,y)
void lcd_draw_string(unsigned int x, unsigned int y, unsigned int color, unsigned char *str)
{int i; unsigned char *ch;for (i=0; str[i]!='\0'; i++) { ch = (unsigned char *)ascii_8_16[(unsigned char)str[i]-0x20];show_8_16(x, y, color, ch); x += 8;if (x >= XSIZE){x -= XSIZE; //\ry += 16; //\n}}
}//appear the picture of 800×480,and the picture of font information in pData
void lcd_appear_picture(const unsigned char *pData)
{u32 x, y, color, p = 0;for (y=0; y<600; y++){for (x=0; x<1024; x++){color = ((pData[p+2] << 0) | (pData[p+1] << 8) | (pData[p+0] << 16));lcd_draw_pic_color(x, y, color);p += 3;}}
}1024600.h
ascii.h
#ifndef __ASCII_H__
#define __ASCII_H__//以下字模与ASCII对应是，只要将 'A'-0x20就可以得到A的字模了
//高8*5宽 ASCII码
//提取方式:纵向取模,字节倒序
//以下是8*16的
//高是16
//横向扫描
const unsigned char ascii_8_16[95][16]=
{
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00,0x18,0x18,0x00,0x00},/*"!",1*/
{0x00,0x48,0x6C,0x24,0x12,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x24,0x24,0x24,0x7F,0x12,0x12,0x12,0x7F,0x12,0x12,0x12,0x00,0x00},/*"#",3*/
{0x00,0x00,0x08,0x1C,0x2A,0x2A,0x0A,0x0C,0x18,0x28,0x28,0x2A,0x2A,0x1C,0x08,0x08},/*"{1}quot;,4*/
{0x00,0x00,0x00,0x22,0x25,0x15,0x15,0x15,0x2A,0x58,0x54,0x54,0x54,0x22,0x00,0x00},/*"%",5*/
{0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0A,0x76,0x25,0x29,0x11,0x91,0x6E,0x00,0x00},/*"&",6*/
{0x00,0x06,0x06,0x04,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x40,0x20,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x10,0x20,0x40,0x00},/*"(",8*/
{0x00,0x02,0x04,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x08,0x08,0x04,0x02,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x08,0x08,0x6B,0x1C,0x1C,0x6B,0x08,0x08,0x00,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x7F,0x08,0x08,0x08,0x08,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x04,0x03},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00},/*".",14*/
{0x00,0x00,0x80,0x40,0x40,0x20,0x20,0x10,0x10,0x08,0x08,0x04,0x04,0x02,0x02,0x00},/*"/",15*/
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x08,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x20,0x20,0x10,0x08,0x04,0x42,0x7E,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x20,0x18,0x20,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x20,0x30,0x28,0x24,0x24,0x22,0x22,0x7E,0x20,0x20,0x78,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x7E,0x02,0x02,0x02,0x1A,0x26,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x38,0x24,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x7E,0x22,0x22,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x24,0x18,0x24,0x42,0x42,0x42,0x3C,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x64,0x58,0x40,0x40,0x24,0x1C,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x04},/*";",27*/
{0x00,0x00,0x00,0x40,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x40,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x40,0x20,0x10,0x08,0x04,0x02,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x46,0x40,0x20,0x10,0x10,0x00,0x18,0x18,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x1C,0x22,0x5A,0x55,0x55,0x55,0x55,0x2D,0x42,0x22,0x1C,0x00,0x00},/*"@",32*/
{0x00,0x00,0x00,0x08,0x08,0x18,0x14,0x14,0x24,0x3C,0x22,0x42,0x42,0xE7,0x00,0x00},/*"A",33*/
{0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x1E,0x22,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x7C,0x42,0x42,0x01,0x01,0x01,0x01,0x01,0x42,0x22,0x1C,0x00,0x00},/*"C",35*/
{0x00,0x00,0x00,0x1F,0x22,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"D",36*/
{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x42,0x42,0x3F,0x00,0x00},/*"E",37*/
{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x02,0x02,0x07,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x3C,0x22,0x22,0x01,0x01,0x01,0x71,0x21,0x22,0x22,0x1C,0x00,0x00},/*"G",39*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x7E,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"H",40*/
{0x00,0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x11,0x0F},/*"J",42*/
{0x00,0x00,0x00,0x77,0x22,0x12,0x0A,0x0E,0x0A,0x12,0x12,0x22,0x22,0x77,0x00,0x00},/*"K",43*/
{0x00,0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x7F,0x00,0x00},/*"L",44*/
{0x00,0x00,0x00,0x77,0x36,0x36,0x36,0x36,0x2A,0x2A,0x2A,0x2A,0x2A,0x6B,0x00,0x00},/*"M",45*/
{0x00,0x00,0x00,0xE3,0x46,0x46,0x4A,0x4A,0x52,0x52,0x52,0x62,0x62,0x47,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x41,0x41,0x22,0x1C,0x00,0x00},/*"O",47*/
{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x42,0x3E,0x02,0x02,0x02,0x02,0x07,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x4D,0x53,0x32,0x1C,0x60,0x00},/*"Q",49*/
{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x3E,0x12,0x12,0x22,0x22,0x42,0xC7,0x00,0x00},/*"R",50*/
{0x00,0x00,0x00,0x7C,0x42,0x42,0x02,0x04,0x18,0x20,0x40,0x42,0x42,0x3E,0x00,0x00},/*"S",51*/
{0x00,0x00,0x00,0x7F,0x49,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"T",52*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"U",53*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x22,0x24,0x24,0x14,0x14,0x18,0x08,0x08,0x00,0x00},/*"V",54*/
{0x00,0x00,0x00,0x6B,0x49,0x49,0x49,0x49,0x55,0x55,0x36,0x22,0x22,0x22,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x18,0x18,0x18,0x24,0x24,0x42,0xE7,0x00,0x00},/*"X",56*/
{0x00,0x00,0x00,0x77,0x22,0x22,0x14,0x14,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x7E,0x21,0x20,0x10,0x10,0x08,0x04,0x04,0x42,0x42,0x3F,0x00,0x00},/*"Z",58*/
{0x00,0x78,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x78,0x00},/*"[",59*/
{0x00,0x00,0x02,0x02,0x04,0x04,0x08,0x08,0x08,0x10,0x10,0x20,0x20,0x20,0x40,0x40},/*"\",60*/
{0x00,0x1E,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1E,0x00},/*"]",61*/
{0x00,0x38,0x44,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF},/*"_",63*/
{0x00,0x06,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x78,0x44,0x42,0x42,0xFC,0x00,0x00},/*"a",65*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x26,0x1A,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x44,0x02,0x02,0x02,0x44,0x38,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x60,0x40,0x40,0x40,0x78,0x44,0x42,0x42,0x42,0x64,0xD8,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x7E,0x02,0x02,0x42,0x3C,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0xF0,0x88,0x08,0x08,0x7E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x22,0x22,0x1C,0x02,0x3C,0x42,0x42,0x3C},/*"g",71*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x3A,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x38,0x20,0x20,0x20,0x20,0x20,0x20,0x22,0x1E},/*"j",74*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x72,0x12,0x0A,0x16,0x12,0x22,0x77,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x92,0x92,0x92,0x92,0x92,0xB7,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3B,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1B,0x26,0x42,0x42,0x42,0x22,0x1E,0x02,0x07},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x44,0x42,0x42,0x42,0x44,0x78,0x40,0xE0},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x77,0x4C,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x42,0x02,0x3C,0x40,0x42,0x3E,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x3E,0x08,0x08,0x08,0x08,0x08,0x30,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x42,0x42,0x42,0x42,0x62,0xDC,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x08,0x08,0x00,0x00},/*"v",86*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEB,0x49,0x49,0x55,0x55,0x22,0x22,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x76,0x24,0x18,0x18,0x18,0x24,0x6E,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x18,0x08,0x08,0x07},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x22,0x10,0x08,0x08,0x44,0x7E,0x00,0x00},/*"z",90*/
{0x00,0xC0,0x20,0x20,0x20,0x20,0x20,0x10,0x20,0x20,0x20,0x20,0x20,0x20,0xC0,0x00},/*"{",91*/
{0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10},/*"|",92*/
{0x00,0x06,0x08,0x08,0x08,0x08,0x08,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x06,0x00},/*"}",93*/
{0x0C,0x32,0xC2,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
};#endiflink.lds
SECTIONS
{. = 0x23E00000;.text : {start.o* (.text)}.data : {* (.data)}.bss : {* (.bss)}}Makefile
CC = arm-linux-gcc
LD = arm-linux-ld
OBJCOPY = arm-linux-objcopy
OBJDUMP = arm-linux-objdumpINCDIR := $(shell pwd)#预处理器的flag，flag就是编译器可选的选项
CPPFLAGS := -nostdlib -nostdinc -I$(INCDIR)/include
#C编译器的flag
CFLAGS := -Wall -O2 -fno-builtinexport CC LD OBJCOPY OBJDUMP CPPFLAGS CFLAGSobjs := start.o main.o lcd.o led.bin:$(objs)$(LD) -Tlink.lds -o sd2.elf $^$(OBJCOPY) -O binary sd2.elf sd2.bin$(OBJDUMP) -D sd2.elf > sd2.dis%.o:%.S$(CC) $(CPPFLAGS) $(CFLAGS) -o $@ $< -c%.o:%.c$(CC) $(CPPFLAGS) $(CFLAGS) -o $@ $< -cclean:rm *.o *.elf *.bin *.dis mkv210 -f文件示例:
