1、在虚拟机中添加网卡2
| [root@ntpserver network-scripts]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens192: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 00:50:56:b3:eb:a8 brd ff:ff:ff:ff:ff:ff inet 10.6.100.18/25 brd 10.6.100.127 scope global noprefixroute ens192 valid_lft forever preferred_lft forever inet6 fe80::72b3:9725:d92f:306/64 scope link tentative noprefixroute dadfailed valid_lft forever preferred_lft forever inet6 fe80::2206:e2ec:6f6c:dd4b/64 scope link tentative noprefixroute dadfailed valid_lft forever preferred_lft forever inet6 fe80::295c:ddf4:9822:5398/64 scope link tentative noprefixroute dadfailed valid_lft forever preferred_lft forever
|
添加完后多了en34
| [root@ntpserver network-scripts]# ip add 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens192: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 00:50:56:b3:eb:a8 brd ff:ff:ff:ff:ff:ff inet 10.6.100.18/25 brd 10.6.100.127 scope global noprefixroute ens192 valid_lft forever preferred_lft forever inet6 fe80::72b3:9725:d92f:306/64 scope link tentative noprefixroute dadfailed valid_lft forever preferred_lft forever inet6 fe80::2206:e2ec:6f6c:dd4b/64 scope link tentative noprefixroute dadfailed valid_lft forever preferred_lft forever inet6 fe80::295c:ddf4:9822:5398/64 scope link tentative noprefixroute dadfailed valid_lft forever preferred_lft forever 3: ens34: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000 link/ether 00:0c:29:16:50:c8 brd ff:ff:ff:ff:ff:ff [root@ntpserver network-scripts]# |
2、vim /etc/sysconfig/network-scripts/ifcfg-ens192 #编辑 ens192 网卡
| TYPE=Ethernet PROXY_METHOD=none BROWSER_ONLY=no BOOTPROTO=none DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_FAILURE_FATAL=no IPV6_ADDR_GEN_MODE=stable-privacy NAME=ens UUID=1a5b3386-6836-46e3-8823-a4fc5088e0b8 DEVICE=ens192 ONBOOT=yes DNS1=10.6.100.10 IPADDR=10.6.100.18 PREFIX=25 GATEWAY=10.6.100.1 |
| DEVICE=ens192 |
DEVICE=eth0 # 网口名eth0
TYPE=Ethernet #网络类型为：Ethernet
ONBOOT=yes #在系统启动时是否激活网卡
NM_CONTROLLED=yes #network mamager的参数，实时生效，不需要重启
BOOTPROTO=none #使用什么协议激活网卡#none表示不使用任何协议 static表示设置静态IP dhcp表示动态获取IP
MASTER=bond0 #指定master为bond0
SLAVE=yes #是否为附属
#USERCTL=no #是否允许非root用户控制该设备，设置为no，只能用root用户更改
| [root@ntpserver network-scripts]# cat ifcfg-ens{192,34} DIVICE=ens192 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=yes BOOTPROTO=none MASTER=bond0 SLAVE=yes USERCTL=no DEVICE=ens34 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=yes BOOTPROTO=none MASTER=bond0 SLAVE=yes #USERCTL=no |
3、vim /etc/sysconfig/network-scripts/ifcfg-ens34 #编辑 ens34网卡
| DEVICE=ens34 |
4、vim /etc/sysconfig/network-scripts/ifcfg-bond0 #创建并配置bond0网卡
#bond，是一种通过把多个物理网卡绑定成一个逻辑网卡实现网卡冗余、负载均衡、提高带宽，从而实现网络性能高可用高可靠的技术。
| DEVICE=bond0 TYPE=Ethernet //bond USERCTL=no DNS1=8.8.8.8 |
5、vi /etc/modprobe.d/dist.conf #配置添加内容
#最后一行添加
alias bond0 bonding
options bond0 miimon=100 mode=6
6、停止 network manager服务
service NetworkManager stop #解决service network restart 闲置网卡报错问题
chkconfig NetworkManager off #移除开机启动
7、重启网卡
service network restart
1.到了这一步最好reboot下，确保下面能一次性成功
2.UUID是唯一的编号，每个网口唯一
3.两个配置文件中HWADDR不能一样，可以不要，因为会自动读取
4.网口切换后 ifconfig bond0查看到的MAC地址还是切换前的MAC地址–>为了防止IP对应MAC地址混乱
8、测试
ping g.cn #双网卡测试
ifconfig eth0 down #关闭eth0
ping g.cn #测试
ifconfig eth0 up #打开eth0
ifconfig eth1 down #关闭eth1
ping g.cn #测试
屏幕剪辑的捕获时间: 9/26/2023 1:45 PM
