STM32存储左右互搏 QSPI总线FATS文件读写FLASH W25QXX

STM32存储左右互搏 QSPI总线FATS文件读写FLASH W25QXX

FLASH是常用的一种非易失存储单元，W25QXX系列Flash有不同容量的型号，如W25Q64的容量为64Mbit，也就是8MByte。这里介绍STM32CUBEIDE开发平台HAL库Quad SPI总线实现FATS文件操作W25Q各型号FLASH的例程。非FATS直接Quad SPI操作W25QXX FLASH的方式见《STM32存储左右互搏 QSPI总线读写FLASH W25QXX》

W25QXX介绍

W25QXX的SOIC封装如下所示，在采用QUAL SPI而不是SPI时，管脚定义为：
在这里插入图片描述
即由片选(/CS), 时钟(CLK), 双向4根输入输出线(IO0, IO1, IO2, IO3)组成6线QSPI信号接口。VCC和GND提供电源和接地连接。

例程采用STM32H750VBT6芯片, FLASH可以选择为8/16/32/64/128/256/512/1024 Mbit的W25Q型号。

STM32工程配置

首先建立基本工程并设置时钟：
在这里插入图片描述

在这里插入图片描述
注意QSPI时钟在单独的时钟树支上：
在这里插入图片描述
QSPI接口可以配置为两个Bank（并行协同存储扩展），也可以配置为单个Bank，并且可以由4线（数据线）模式降级为单线/双线（数据线）模式。这里对于单个Flash，选择一个bank配置：
在这里插入图片描述
在这里插入图片描述
注意QSPI的片选信号是硬件自动控制，和SPI可以采用软件代码控制不同，所以不必单独指定一个GPIO作为片选：
在这里插入图片描述
不用DMA
在这里插入图片描述
配置FATS参数：
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
配置串口UART1作为命令输入和打印输出接口：
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
不用DMA:
在这里插入图片描述
保存并生成初始工程代码：
在这里插入图片描述

STM32工程代码

UART串口printf打印输出实现参考：STM32 UART串口printf函数应用及浮点打印代码空间节省 (HAL)

建立W25Q访问的库头文件W25QXX_QSPI.h:*

#ifndef INC_W25QXX_H_
#define INC_W25QXX_H_#include "main.h"//W25QXX serial chip list:
#define W25Q80_ID 	0XEF13
#define W25Q16_ID 	0XEF14
#define W25Q32_ID 	0XEF15
#define W25Q64_ID 	0XEF16
#define W25Q128_ID	0XEF17
#define W25Q256_ID 0XEF18
#define W25Q512_ID 0XEF19
#define W25Q1024_ID 0XEF20extern uint16_t W25QXX_TYPE; //To indicate W25QXX type used in this procedure//command table for W25QXX access
#define W25X_WriteEnable		0x06
#define W25X_WriteDisable		0x04
#define W25X_ReadStatusReg1		0x05
#define W25X_ReadStatusReg2		0x35
#define W25X_ReadStatusReg3		0x15
#define W25X_WriteStatusReg1    0x01
#define W25X_WriteStatusReg2    0x31
#define W25X_WriteStatusReg3    0x11
#define W25X_ReadData			0x03
#define W25X_FastReadData		0x0B
#define W25X_FastReadDual		0x3B
#define W25X_PageProgram		0x02
#define W25X_BlockErase			0xD8
#define W25X_SectorErase		0x20
#define W25X_ChipErase			0xC7
#define W25X_PowerDown			0xB9
#define W25X_ReleasePowerDown	0xAB
#define W25X_DeviceID			0xAB
#define W25X_ManufactDeviceID	0x90
#define W25X_JedecDeviceID		0x9F
#define W25X_Enable4ByteAddr    0xB7
#define W25X_Exit4ByteAddr      0xE9#define W25X_QUAD_QuadInputPageProgram 0x32
#define W25X_QUAD_FastReadQuadOutput 0x6B
#define W25X_QUAD_ManufactDeviceID 0x94
#define W25X_QUAD_FastRead 0xEB
#define W25X_QUAD_SetBurstwithWrap 0x77uint8_t W25QXX_Init(void);
uint16_t  W25QXX_ReadID(void);  	    		  //Read W25QXX ID
uint8_t W25QXX_ReadSR(uint8_t reg_num);           //Read from status register
void W25QXX_4ByteAddr_Enable(void);               //Enable 4-byte address mode
void W25QXX_Write_SR(uint8_t reg_num,uint8_t d);  //Write to status register
void W25QXX_Write_Enable(void);  		          //Write enable
void W25QXX_Write_Disable(void);		          //Write disable
void W25QXX_Write_NoCheck(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite); //Write operation w/o check
void W25QXX_Read(uint8_t* pBuffer,uint32_t ReadAddr,uint16_t NumByteToRead);            //Read operation
void W25QXX_Write(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite);         //Write operation
void W25QXX_Erase_Chip(void);    	  	                                                //Erase whole chip
void W25QXX_Erase_Sector(uint32_t Sector_Num);	                                        //Erase sector in specific sector number
void W25QXX_Wait_Busy(void);           	       //Wait idle status before next operation
void W25QXX_PowerDown(void);        	       //Enter power-down mode
void W25QXX_WAKEUP(void);				       //Wake-up#endif /* INC_W25QXX_H_ */

建立W25Q访问的库源文件W25QXX_QSPI.c:

#include "W25QXX_QSPI.h"extern QSPI_HandleTypeDef hqspi;
extern void PY_Delay_us_t(uint32_t Delay);
extern HAL_StatusTypeDef QSPI_Send_CMD(uint8_t cmd,uint32_t addr,uint8_t mode,uint8_t dmcycle);
extern HAL_StatusTypeDef QSPI_Receive(uint8_t* buf,uint32_t datalen);
extern HAL_StatusTypeDef QSPI_Transmit(uint8_t* buf,uint32_t datalen);#define Use_Quad_Line 1uint16_t W25QXX_TYPE=W25Q64_ID;//W25QXX initialization
uint8_t W25QXX_Init(void)
{uint8_t temp;W25QXX_TYPE=W25QXX_ReadID();if((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)){temp=W25QXX_ReadSR(3);              //read status register 3if((temp&0X01)==0)			        //judge address mode and configure to 4-byte address mode{QSPI_Send_CMD(W25X_Enable4ByteAddr, 0x00, (0<<6)|(0<<4)|(0<<2)|(1<<0), 0);}}if((W25QXX_TYPE==0x0000)||(W25QXX_TYPE==0xFFFF)) return 0;else return 1;
}//Read status registers of W25QXX
//reg_num: register number from 1 to 3
//return: value of selected register//SR1 (default 0x00)：
//BIT7  6   5   4   3   2   1   0
//SPR   RV  TB BP2 BP1 BP0 WEL BUSY
//SPR: default 0, status register protection bit used with WP
//TB,BP2,BP1,BP0: FLASH region write protection configuration
//WEL: write enable lock
//BUSY: busy flag (1: busy; 0: idle)//SR2：
//BIT7  6   5   4   3   2   1   0
//SUS   CMP LB3 LB2 LB1 (R) QE  SRP1//SR3：
//BIT7      6    5    4   3   2   1   0
//HOLD/RST  DRV1 DRV0 (R) (R) WPS ADP ADS
uint8_t W25QXX_ReadSR(uint8_t reg_num)
{uint8_t byte=0,command=0;switch(reg_num){case 1:command=W25X_ReadStatusReg1;    //To read status register 1break;case 2:command=W25X_ReadStatusReg2;    //To read status register 2break;case 3:command=W25X_ReadStatusReg3;    //To read status register 3break;default:command=W25X_ReadStatusReg1;break;}QSPI_Send_CMD(command, 0x00, (1<<6)|(0<<4)|(0<<2)|(1<<0), 0);  //send commandQSPI_Receive(&byte,1);                                         //read datareturn byte;
}//Write status registers of W25QXX
//reg_num: register number from 1 to 3
//d: data for updating status register
void W25QXX_Write_SR(uint8_t reg_num,uint8_t d)
{uint8_t command=0;switch(reg_num){case 1:command=W25X_WriteStatusReg1;    //To write status register 1break;case 2:command=W25X_WriteStatusReg2;    //To write status register 2break;case 3:command=W25X_WriteStatusReg3;    //To write status register 3break;default:command=W25X_WriteStatusReg1;break;}QSPI_Send_CMD(command, 0x00, (1<<6)|(0<<4)|(0<<2)|(1<<0), 0); //send commandQSPI_Transmit(&d, 1);                                         //write data
}
//W25QXX write enable
void W25QXX_Write_Enable(void)
{QSPI_Send_CMD(W25X_WriteEnable, 0x00, (0<<6)|(0<<4)|(0<<2)|(1<<0), 0); //send command
}
//W25QXX write disable
void W25QXX_Write_Disable(void)
{QSPI_Send_CMD(W25X_WriteDisable, 0x00, (0<<6)|(0<<4)|(0<<2)|(1<<0), 0); //send command
}//Read chip ID
//return:
//0XEF13 for W25Q80
//0XEF14 for W25Q16
//0XEF15 for W25Q32
//0XEF16 for W25Q64
//0XEF17 for W25Q128
//0XEF18 for W25Q256
uint16_t W25QXX_ReadID(void)
{uint16_t Temp = 0;uint8_t st;uint8_t TD[8];if(Use_Quad_Line){uint8_t extra_dummy = 4; //Adjust dummy here for I/O direction adjustment delayQSPI_Send_CMD(W25X_QUAD_ManufactDeviceID, 0x000000f0, (3<<6)|(3<<4)|(3<<2)|(1<<0), extra_dummy);   ///To read Manufacturer/Device ID in Quad modest = QSPI_Receive(TD, 2);if(st==0){Temp = (TD[0]<<8)|TD[1];}else{Temp = 0;}return Temp;}else{QSPI_Send_CMD(W25X_ManufactDeviceID, 0x00, (1<<6)|(0<<4)|(0<<2)|(1<<0), 0);  //To read Manufacturer/Device ID in single line modest = QSPI_Receive(TD, 5);if(st==0){Temp = (TD[3]<<8)|TD[4];}else{Temp = 0;}return Temp;}
}
//Read W25QXX from specific address for specific byte length
//pBuffer: data buffer
//ReadAddr: specific address
//NumByteToRead: specific byte length (max 65535)
void W25QXX_Read(uint8_t* pBuffer,uint32_t ReadAddr,uint16_t NumByteToRead)
{if(Use_Quad_Line){uint8_t extra_dummy = 8;    //Adjust dummy here for I/O direction adjustment delayif((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)){QSPI_Send_CMD(W25X_QUAD_FastReadQuadOutput, ReadAddr, (3<<6)|(3<<4)|(1<<2)|(1<<0), extra_dummy);}else{QSPI_Send_CMD(W25X_QUAD_FastReadQuadOutput, ReadAddr, (3<<6)|(2<<4)|(1<<2)|(1<<0), extra_dummy);}QSPI_Receive(pBuffer, NumByteToRead); //read data}else{uint8_t extra_dummy = 8;    //Adjust dummy here for I/O direction adjustment delayif((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)){QSPI_Send_CMD(W25X_ReadData, ReadAddr, (1<<6)|(3<<4)|(1<<2)|(1<<0), extra_dummy);}else{QSPI_Send_CMD(W25X_ReadData, ReadAddr, (1<<6)|(2<<4)|(1<<2)|(1<<0), extra_dummy);}QSPI_Receive(pBuffer, NumByteToRead); //read data}}//Write W25QXX not more than 1 page (256 bytes)
//pBuffer: data buffer
//WriteAddr: specific address
//NumByteToWrite: specific byte length (max 256)
void W25QXX_Write_Page(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite)
{W25QXX_Write_Enable();                                        //write enable//send write commandif(Use_Quad_Line){if((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)){QSPI_Send_CMD(W25X_QUAD_QuadInputPageProgram, WriteAddr, (3<<6)|(3<<4)|(1<<2)|(1<<0), 0);}else{QSPI_Send_CMD(W25X_QUAD_QuadInputPageProgram, WriteAddr, (3<<6)|(2<<4)|(1<<2)|(1<<0), 0);}}else{if((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)){QSPI_Send_CMD(W25X_PageProgram, WriteAddr, (1<<6)|(3<<4)|(1<<2)|(1<<0), 0);}else{QSPI_Send_CMD(W25X_PageProgram, WriteAddr, (1<<6)|(2<<4)|(1<<2)|(1<<0), 0);}}QSPI_Transmit(pBuffer, NumByteToWrite); //write dataW25QXX_Wait_Busy();
}//Write W25QXX w/o erase check and w/o byte number restriction
//pBuffer: data buffer
//WriteAddr: specific address
//NumByteToWrite: specific byte length (max 65535)
void W25QXX_Write_NoCheck(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite)
{uint16_t remained_byte_num_in_page;remained_byte_num_in_page=256-WriteAddr%256;                                                       //remained byte number in pageif( NumByteToWrite <= remained_byte_num_in_page ) remained_byte_num_in_page = NumByteToWrite;      //data can be written in single pagewhile(1){W25QXX_Write_Page(pBuffer,WriteAddr,remained_byte_num_in_page);if(NumByteToWrite==remained_byte_num_in_page)break;                                            //end write operationelse                                                                                           //NumByteToWrite>remained_byte_num_in_page{pBuffer+=remained_byte_num_in_page;WriteAddr+=remained_byte_num_in_page;NumByteToWrite-=remained_byte_num_in_page;if(NumByteToWrite>256) remained_byte_num_in_page=256;                                       //for whole page writeelse remained_byte_num_in_page=NumByteToWrite; 	                                           //for non-whole page write}};
}//Write W25QXX w/ erase after check and w/o byte number restriction
//pBuffer: data buffer
//WriteAddr: specific address
//NumByteToWrite: specific byte length (max 65535)
uint8_t W25QXX_BUFFER[4096];
void W25QXX_Write(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite)
{uint32_t secpos;uint16_t secoff;uint16_t secremain;uint16_t i;uint8_t * W25QXX_BUF;W25QXX_BUF=W25QXX_BUFFER;secpos=WriteAddr/4096;                                        //sector number (16 pages for 1 sector) for destination addresssecoff=WriteAddr%4096;                                        //offset address in sector for destination addresssecremain=4096-secoff;                                        //remained space for sectorif(NumByteToWrite<=secremain)secremain=NumByteToWrite;        //data can be written in single sectorwhile(1){W25QXX_Read(W25QXX_BUF,secpos*4096,4096);                 //read sector data for ease necessity judgmentfor(i=0;i<secremain;i++)                                  //check sector data status{if(W25QXX_BUF[secoff+i]!=0XFF) break;                 //ease necessary}if(i<secremain)                                           //for ease{W25QXX_Erase_Sector(secpos);                          //ease sectorfor(i=0;i<secremain;i++)	                          //data copy{W25QXX_BUF[i+secoff]=pBuffer[i];}W25QXX_Write_NoCheck(W25QXX_BUF,secpos*4096,4096);     //write sector}else W25QXX_Write_NoCheck(pBuffer,WriteAddr,secremain);   //write data for sector unnecessary to eraseif(NumByteToWrite==secremain)break;                        //for operation endelse                                                       //for operation continuing{secpos++;                                              //sector number + 1secoff=0;                                              //offset address from 0pBuffer+=secremain;                                    //pointer adjustmentWriteAddr+=secremain;                                  //write address adjustmentNumByteToWrite-=secremain;				               //write number adjustmentif(NumByteToWrite>4096) secremain=4096;	               //not last sectorelse secremain=NumByteToWrite;			               //last sector}};
}//Erase whole chip, long waiting...
void W25QXX_Erase_Chip(void)
{W25QXX_Write_Enable();                  //write enableW25QXX_Wait_Busy();QSPI_Send_CMD(W25X_ChipErase, 0x00, (0<<6)|(0<<4)|(0<<2)|(1<<0), 0); //send erase commandW25QXX_Wait_Busy();   				    //wait for erase complete
}//Erase one sector
//Sector_Num: sector number
void W25QXX_Erase_Sector(uint32_t Sector_Num)
{Sector_Num *= 4096;W25QXX_Write_Enable();                                     //write enableW25QXX_Wait_Busy();if((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)) //send highest 8-bit address{QSPI_Send_CMD(W25X_SectorErase, Sector_Num, (0<<6)|(3<<4)|(1<<2)|(1<<0), 0); //send erase command}else{QSPI_Send_CMD(W25X_SectorErase, Sector_Num, (0<<6)|(2<<4)|(1<<2)|(1<<0), 0); //send erase command}W25QXX_Wait_Busy();   				                       //wait for erase complete
}//Wait idle status before next operation
void W25QXX_Wait_Busy(void)
{while((W25QXX_ReadSR(1)&0x01)==0x01);    //wait for busy flag cleared
}//Enter power-down mode
#define tDP_us 3
void W25QXX_PowerDown(void)
{QSPI_Send_CMD(W25X_PowerDown, 0, (0<<6)|(0<<4)|(0<<2)|(1<<0), 0);        //send power-down commandPY_Delay_us_t(tDP_us);                   //tDP
}
//Wake-up
#define tRES1_us 3
void W25QXX_WAKEUP(void)
{QSPI_Send_CMD(W25X_ReleasePowerDown, 0, (0<<6)|(0<<4)|(0<<2)|(1<<0), 0); //send release power-down commandPY_Delay_us_t(tRES1_us);                 //tRES1
}

对ffconf.h添加包含信息：
在这里插入图片描述

#include "main.h"
#include "stm32h7xx_hal.h"

修改user_diskio.c，对文件操作函数与底层FLASH读写提供连接：

/* USER CODE BEGIN Header */
/********************************************************************************* @file    user_diskio.c* @brief   This file includes a diskio driver skeleton to be completed by the user.******************************************************************************* @attention** Copyright (c) 2023 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************//* USER CODE END Header */#ifdef USE_OBSOLETE_USER_CODE_SECTION_0
/** Warning: the user section 0 is no more in use (starting from CubeMx version 4.16.0)* To be suppressed in the future.* Kept to ensure backward compatibility with previous CubeMx versions when* migrating projects.* User code previously added there should be copied in the new user sections before* the section contents can be deleted.*/
/* USER CODE BEGIN 0 */
/* USER CODE END 0 */
#endif/* USER CODE BEGIN DECL */
/**************************SELF DEFINITION PART************/
#include "diskio.h"		/* Declarations of disk functions */
#include "W25QXX_QSPI.h"
/**********************************************************/
/* Includes ------------------------------------------------------------------*/
#include <string.h>
#include "ff_gen_drv.h"/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*//* Private variables ---------------------------------------------------------*/
/* Disk status */
static volatile DSTATUS Stat = STA_NOINIT;/* USER CODE END DECL *//* Private function prototypes -----------------------------------------------*/
DSTATUS USER_initialize (BYTE pdrv);
DSTATUS USER_status (BYTE pdrv);
DRESULT USER_read (BYTE pdrv, BYTE *buff, DWORD sector, UINT count);
#if _USE_WRITE == 1DRESULT USER_write (BYTE pdrv, const BYTE *buff, DWORD sector, UINT count);
#endif /* _USE_WRITE == 1 */
#if _USE_IOCTL == 1DRESULT USER_ioctl (BYTE pdrv, BYTE cmd, void *buff);
#endif /* _USE_IOCTL == 1 */Diskio_drvTypeDef  USER_Driver =
{USER_initialize,USER_status,USER_read,
#if  _USE_WRITEUSER_write,
#endif  /* _USE_WRITE == 1 */
#if  _USE_IOCTL == 1USER_ioctl,
#endif /* _USE_IOCTL == 1 */
};/* Private functions ---------------------------------------------------------*//*** @brief  Initializes a Drive* @param  pdrv: Physical drive number (0..)* @retval DSTATUS: Operation status*/
DSTATUS USER_initialize (BYTE pdrv           /* Physical drive nmuber to identify the drive */
)
{/* USER CODE BEGIN INIT *//**************************SELF DEFINITION PART************/uint8_t res;res = W25QXX_Init();if(res) return RES_OK;else return  STA_NOINIT;/**********************************************************//*Stat = STA_NOINIT;return Stat;*//* USER CODE END INIT */
}/*** @brief  Gets Disk Status* @param  pdrv: Physical drive number (0..)* @retval DSTATUS: Operation status*/
DSTATUS USER_status (BYTE pdrv       /* Physical drive number to identify the drive */
)
{/* USER CODE BEGIN STATUS *//**************************SELF DEFINITION PART************/switch (pdrv){case 0 :return RES_OK;case 1 :return RES_OK;case 2 :return RES_OK;default:return STA_NOINIT;}/**********************************************************//*Stat = STA_NOINIT;return Stat;*//* USER CODE END STATUS */
}/*** @brief  Reads Sector(s)* @param  pdrv: Physical drive number (0..)* @param  *buff: Data buffer to store read data* @param  sector: Sector address (LBA)* @param  count: Number of sectors to read (1..128)* @retval DRESULT: Operation result*/
DRESULT USER_read (BYTE pdrv,      /* Physical drive nmuber to identify the drive */BYTE *buff,     /* Data buffer to store read data */DWORD sector,   /* Sector address in LBA */UINT count      /* Number of sectors to read */
)
{/* USER CODE BEGIN READ *//**************************SELF DEFINITION PART************/uint16_t len;if( !count ){return RES_PARERR;  /* count不能等于0，否则返回参数错误*/}switch (pdrv){case 0:sector <<= 9; //Convert sector number to byte addresslen = count*512;W25QXX_Read(buff, sector, len);return RES_OK;default:return RES_ERROR;}/**********************************************************//*return RES_OK;*//* USER CODE END READ */
}/*** @brief  Writes Sector(s)* @param  pdrv: Physical drive number (0..)* @param  *buff: Data to be written* @param  sector: Sector address (LBA)* @param  count: Number of sectors to write (1..128)* @retval DRESULT: Operation result*/
#if _USE_WRITE == 1
DRESULT USER_write (BYTE pdrv,          /* Physical drive nmuber to identify the drive */const BYTE *buff,   /* Data to be written */DWORD sector,       /* Sector address in LBA */UINT count          /* Number of sectors to write */
)
{/* USER CODE BEGIN WRITE *//* USER CODE HERE *//**************************SELF DEFINITION PART************/uint16_t len;if( !count ){return RES_PARERR;  /* count不能等于0，否则返回参数错误*/}switch (pdrv){case 0:sector <<= 9; //Convert sector number to byte addresslen = count*512;W25QXX_Write((uint8_t *)buff, sector, len);return RES_OK;default:return RES_ERROR;}/*********************************************************//*return RES_OK;*//* USER CODE END WRITE */
}
#endif /* _USE_WRITE == 1 *//*** @brief  I/O control operation* @param  pdrv: Physical drive number (0..)* @param  cmd: Control code* @param  *buff: Buffer to send/receive control data* @retval DRESULT: Operation result*/
#if _USE_IOCTL == 1
DRESULT USER_ioctl (BYTE pdrv,      /* Physical drive nmuber (0..) */BYTE cmd,       /* Control code */void *buff      /* Buffer to send/receive control data */
)
{/* USER CODE BEGIN IOCTL *//**************************SELF DEFINITION PART************/#define user_sector_byte_size 512DRESULT res;switch(cmd){case CTRL_SYNC:W25QXX_Wait_Busy();res=RES_OK;break;case GET_SECTOR_SIZE:*(WORD*)buff = user_sector_byte_size;res = RES_OK;break;case GET_BLOCK_SIZE:*(WORD*)buff = 4096/user_sector_byte_size;res = RES_OK;break;case GET_SECTOR_COUNT:W25QXX_TYPE=W25QXX_ReadID();if(W25QXX_TYPE==W25Q80_ID) *(DWORD*)buff = (8*1024*1024/512);else if(W25QXX_TYPE==W25Q16_ID) *(DWORD*)buff = (16*1024*1024/512);else if(W25QXX_TYPE==W25Q32_ID) *(DWORD*)buff = (32*1024*1024/512);else if(W25QXX_TYPE==W25Q64_ID) *(DWORD*)buff = (64*1024*1024/512);else if(W25QXX_TYPE==W25Q128_ID) *(DWORD*)buff = (128*1024*1024/512);else if(W25QXX_TYPE==W25Q256_ID) *(DWORD*)buff = (256*1024*1024/512);else if(W25QXX_TYPE==W25Q512_ID) *(DWORD*)buff = (512*1024*1024/512);else if(W25QXX_TYPE==W25Q1024_ID) *(DWORD*)buff = (1024*1024*1024/512);else *(DWORD*)buff = (8*1024*1024/512);res = RES_OK;break;default:res = RES_PARERR;break;}return res;/**********************************************************//*DRESULT res = RES_ERROR;return res;*//* USER CODE END IOCTL */
}
#endif /* _USE_IOCTL == 1 */

main.c文件操作代码里包含几个QSPI操作函数定义如下：

#define page_byte_size 256
uint8_t sdbuffer[page_byte_size];/*
QSPI TX in block mode for command byte
cmd: command to be sent to device
addr: address to be sent to device
mode: operation mode set asmode[1:0] for command transmission mode ( 00: no command; 01: single-line transmission; 10: dual-line transmission; 11: four-line transmission )mode[3:2] for address transmission mode ( 00: no address; 01: single-line transmission; 10: dual-line transmission; 11: four-line transmission )mode[5:4] for address length ( 00:8-bit address; 01: 16-bit address; 10: 24-bit address; 11: 32-bit address )mode[7:6] for data transmission mode ( 00: no command; 01: single-line transmission; 10: dual-line transmission; 11: four-line transmission )
dmcycle: dummy clock cycle
*/
HAL_StatusTypeDef QSPI_Send_CMD(uint8_t cmd,uint32_t addr,uint8_t mode,uint8_t dmcycle)
{QSPI_CommandTypeDef Cmdhandler;Cmdhandler.Instruction=cmd;		//set cmdCmdhandler.Address=addr;		//set addressCmdhandler.DummyCycles=dmcycle; //set dummy circle number/*set cmd transmission mode*/if(((mode>>0)&0x03) == 0)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_NONE;else if(((mode>>0)&0x03) == 1)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_1_LINE;else if(((mode>>0)&0x03) == 2)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_2_LINES;else if(((mode>>0)&0x03) == 3)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_4_LINES;/*set address transmission mode*/if(((mode>>2)&0x03) == 0)Cmdhandler.AddressMode=QSPI_ADDRESS_NONE;else if(((mode>>2)&0x03) == 1)Cmdhandler.AddressMode=QSPI_ADDRESS_1_LINE;else if(((mode>>2)&0x03) == 2)Cmdhandler.AddressMode=QSPI_ADDRESS_2_LINES;else if(((mode>>2)&0x03) == 3)Cmdhandler.AddressMode=QSPI_ADDRESS_4_LINES;/*set address length*/if(((mode>>4)&0x03) == 0)Cmdhandler.AddressSize=QSPI_ADDRESS_8_BITS;else if(((mode>>4)&0x03) == 1)Cmdhandler.AddressSize=QSPI_ADDRESS_16_BITS;else if(((mode>>4)&0x03) == 2)Cmdhandler.AddressSize=QSPI_ADDRESS_24_BITS;else if(((mode>>4)&0x03) == 3)Cmdhandler.AddressSize=QSPI_ADDRESS_32_BITS;/*set data transmission mode*/if(((mode>>6)&0x03) == 0)Cmdhandler.DataMode=QSPI_DATA_NONE;else if(((mode>>6)&0x03) == 1)Cmdhandler.DataMode=QSPI_DATA_1_LINE;else if(((mode>>6)&0x03) == 2)Cmdhandler.DataMode=QSPI_DATA_2_LINES;else if(((mode>>6)&0x03) == 3)Cmdhandler.DataMode=QSPI_DATA_4_LINES;Cmdhandler.SIOOMode=QSPI_SIOO_INST_EVERY_CMD;				/*Send instruction on every transaction*/Cmdhandler.AlternateByteMode=QSPI_ALTERNATE_BYTES_NONE;		/*No alternate bytes*/Cmdhandler.DdrMode=QSPI_DDR_MODE_DISABLE;					/*Double data rate mode disabled*/Cmdhandler.DdrHoldHalfCycle=QSPI_DDR_HHC_ANALOG_DELAY;      /*Delay the data output using analog delay in DDR mode*/return HAL_QSPI_Command(&hqspi,&Cmdhandler,5000);
}//QSPI RX in block mode for data
//buf : buffer address for RX data
//datalen : RX data length
//return : 0, OK
//         others, error code
HAL_StatusTypeDef QSPI_Receive(uint8_t* buf,uint32_t datalen)
{hqspi.Instance->DLR=datalen-1;return HAL_QSPI_Receive(&hqspi,buf,5000);
}//QSPI TX in block mode for data
//buf : buffer address for TX data
//datalen : TX data length
//return : 0, OK
//         others, error code
HAL_StatusTypeDef QSPI_Transmit(uint8_t* buf,uint32_t datalen)
{hqspi.Instance->DLR=datalen-1;return HAL_QSPI_Transmit(&hqspi,buf,5000);
}

然后在main.c里根据串口输入命令（16进制单字节）实现如下功能：
0x01. 读取FLASH ID
0x02. 装载FATS文件系统
0x03: 创建/打开文件并从头位置写入数据
0x04: 打开文件并从头位置读入数据
0x05: 创建/打开文件并从特定位置写入数据
0x06: 打开文件并从特定位置读入数据
完整的代码实现如下：

/* USER CODE BEGIN Header */
/********************************************************************************* @file           : main.c* @brief          : Main program body******************************************************************************* @attention** Copyright (c) 2023 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************/
//Written by Pegasus Yu in 2023
//NOte: to access W25Qxx, send single line command at first to trigger consequent operation mode for address and data which could be 1-line or 4-line
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "fatfs.h"/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include <string.h>
#include "usart.h"
#include "W25QXX_QSPI.h"
/* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
__IO float usDelayBase;
void PY_usDelayTest(void)
{__IO uint32_t firstms, secondms;__IO uint32_t counter = 0;firstms = HAL_GetTick()+1;secondms = firstms+1;while(uwTick!=firstms) ;while(uwTick!=secondms) counter++;usDelayBase = ((float)counter)/1000;
}void PY_Delay_us_t(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t usNum = (uint32_t)(Delay*usDelayBase);delayReg = 0;while(delayReg!=usNum) delayReg++;
}void PY_usDelayOptimize(void)
{__IO uint32_t firstms, secondms;__IO float coe = 1.0;firstms = HAL_GetTick();PY_Delay_us_t(1000000) ;secondms = HAL_GetTick();coe = ((float)1000)/(secondms-firstms);usDelayBase = coe*usDelayBase;
}void PY_Delay_us(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t msNum = Delay/1000;__IO uint32_t usNum = (uint32_t)((Delay%1000)*usDelayBase);if(msNum>0) HAL_Delay(msNum);delayReg = 0;while(delayReg!=usNum) delayReg++;
}
/* USER CODE END PTD *//* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD *//* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*/QSPI_HandleTypeDef hqspi;UART_HandleTypeDef huart1;/* USER CODE BEGIN PV */
uint8_t uart1_rx[16];
uint8_t cmd;uint8_t Flash_mount_status = 0; //FLASH fats mount status indication (0: unmount; 1: mount)
uint8_t FATS_Buff[_MAX_SS]; //Buffer for f_mkfs() operationFRESULT retFLASH;
FIL file;
FATFS *fs;UINT bytesread;
UINT byteswritten;
uint8_t rBuffer[20];      //Buffer for read
uint8_t WBuffer[20] ={1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20}; //Buffer for write#define user_sector_byte_size 512
uint8_t flashbuffer[user_sector_byte_size];
/* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART1_UART_Init(void);
static void MX_QUADSPI_Init(void);
/* USER CODE BEGIN PFP *//* USER CODE END PFP *//* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 *//*
QSPI TX in block mode for command byte
cmd: command to be sent to device
addr: address to be sent to device
mode: operation mode set asmode[1:0] for command transmission mode ( 00: no command; 01: single-line transmission; 10: dual-line transmission; 11: four-line transmission )mode[3:2] for address transmission mode ( 00: no address; 01: single-line transmission; 10: dual-line transmission; 11: four-line transmission )mode[5:4] for address length ( 00:8-bit address; 01: 16-bit address; 10: 24-bit address; 11: 32-bit address )mode[7:6] for data transmission mode ( 00: no command; 01: single-line transmission; 10: dual-line transmission; 11: four-line transmission )
dmcycle: dummy clock cycle
*/
HAL_StatusTypeDef QSPI_Send_CMD(uint8_t cmd,uint32_t addr,uint8_t mode,uint8_t dmcycle)
{QSPI_CommandTypeDef Cmdhandler;Cmdhandler.Instruction=cmd;		//set cmdCmdhandler.Address=addr;		//set addressCmdhandler.DummyCycles=dmcycle; //set dummy circle number/*set cmd transmission mode*/if(((mode>>0)&0x03) == 0)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_NONE;else if(((mode>>0)&0x03) == 1)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_1_LINE;else if(((mode>>0)&0x03) == 2)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_2_LINES;else if(((mode>>0)&0x03) == 3)Cmdhandler.InstructionMode=QSPI_INSTRUCTION_4_LINES;/*set address transmission mode*/if(((mode>>2)&0x03) == 0)Cmdhandler.AddressMode=QSPI_ADDRESS_NONE;else if(((mode>>2)&0x03) == 1)Cmdhandler.AddressMode=QSPI_ADDRESS_1_LINE;else if(((mode>>2)&0x03) == 2)Cmdhandler.AddressMode=QSPI_ADDRESS_2_LINES;else if(((mode>>2)&0x03) == 3)Cmdhandler.AddressMode=QSPI_ADDRESS_4_LINES;/*set address length*/if(((mode>>4)&0x03) == 0)Cmdhandler.AddressSize=QSPI_ADDRESS_8_BITS;else if(((mode>>4)&0x03) == 1)Cmdhandler.AddressSize=QSPI_ADDRESS_16_BITS;else if(((mode>>4)&0x03) == 2)Cmdhandler.AddressSize=QSPI_ADDRESS_24_BITS;else if(((mode>>4)&0x03) == 3)Cmdhandler.AddressSize=QSPI_ADDRESS_32_BITS;/*set data transmission mode*/if(((mode>>6)&0x03) == 0)Cmdhandler.DataMode=QSPI_DATA_NONE;else if(((mode>>6)&0x03) == 1)Cmdhandler.DataMode=QSPI_DATA_1_LINE;else if(((mode>>6)&0x03) == 2)Cmdhandler.DataMode=QSPI_DATA_2_LINES;else if(((mode>>6)&0x03) == 3)Cmdhandler.DataMode=QSPI_DATA_4_LINES;Cmdhandler.SIOOMode=QSPI_SIOO_INST_EVERY_CMD;				/*Send instruction on every transaction*/Cmdhandler.AlternateByteMode=QSPI_ALTERNATE_BYTES_NONE;		/*No alternate bytes*/Cmdhandler.DdrMode=QSPI_DDR_MODE_DISABLE;					/*Double data rate mode disabled*/Cmdhandler.DdrHoldHalfCycle=QSPI_DDR_HHC_ANALOG_DELAY;      /*Delay the data output using analog delay in DDR mode*/return HAL_QSPI_Command(&hqspi,&Cmdhandler,5000);
}//QSPI RX in block mode for data
//buf : buffer address for RX data
//datalen : RX data length
//return : 0, OK
//         others, error code
HAL_StatusTypeDef QSPI_Receive(uint8_t* buf,uint32_t datalen)
{hqspi.Instance->DLR=datalen-1;return HAL_QSPI_Receive(&hqspi,buf,5000);
}//QSPI TX in block mode for data
//buf : buffer address for TX data
//datalen : TX data length
//return : 0, OK
//         others, error code
HAL_StatusTypeDef QSPI_Transmit(uint8_t* buf,uint32_t datalen)
{hqspi.Instance->DLR=datalen-1;return HAL_QSPI_Transmit(&hqspi,buf,5000);
}extern char USERPath[4];
/* USER CODE END 0 *//*** @brief  The application entry point.* @retval int*/
int main(void)
{/* USER CODE BEGIN 1 */Flash_mount_status = 0;uint32_t FLASH_Read_Size;char * dpath = "0:"; //Disk Pathfor(uint8_t i=0; i<4; i++){USERPath[i] = *(dpath+i);}const TCHAR* filepath = "0:test.txt";/* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_USART1_UART_Init();MX_QUADSPI_Init();MX_FATFS_Init();/* USER CODE BEGIN 2 */PY_usDelayTest();PY_usDelayOptimize();HAL_UART_Receive_IT(&huart1, uart1_rx, 1);W25QXX_Init();/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){if(cmd==0x01) //Read ID{cmd = 0;printf("Flash ID = 0x%x\r\n\r\n",  W25QXX_ReadID());printf("W25Q80_ID: 0XEF13\r\n");printf("W25Q16_ID: 0XEF14\r\n");printf("W25Q32_ID: 0XEF15\r\n");printf("W25Q64_ID: 0XEF16\r\n");printf("W25Q128_ID: 0XEF17\r\n");printf("W25Q256_ID: 0XEF18\r\n");printf("W25Q512_ID: 0XEF18\r\n");printf("W25Q1024_ID: 0XEF20\r\n");}else if(cmd==2) //Flash File System Mount{cmd = 0;retFLASH=f_mount(&USERFatFS, (TCHAR const*)USERPath, 1);if (retFLASH != FR_OK){printf("File system mount failure: %d\r\n", retFLASH);if(retFLASH==FR_NO_FILESYSTEM){printf("No file system. Now to format......\r\n");retFLASH = f_mkfs((TCHAR const*)USERPath, FM_FAT, 1024, FATS_Buff, sizeof(FATS_Buff)); //FLASH formattingif(retFLASH == FR_OK){printf("FLASH formatting success!\r\n");}else{printf("FLASH formatting failure!\r\n");}}}else{Flash_mount_status = 1;printf("File system mount success\r\n");}}else if(cmd==3) //File creation and write{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open( &file, filepath, FA_CREATE_ALWAYS | FA_WRITE );  //Open or create fileif(retFLASH == FR_OK){printf("\r\nFile open or creation successful\r\n");retFLASH = f_write( &file, (const void *)WBuffer, sizeof(WBuffer), &byteswritten); //Write dataif(retFLASH == FR_OK){printf("\r\nFile write successful\r\n");}else{printf("\r\nFile write error: %d\r\n",retFLASH);}f_close(&file);   //Close file}else{printf("\r\nFile open or creation error %d\r\n",retFLASH);}}}else if(cmd==4) //File read{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open( &file, filepath, FA_OPEN_EXISTING | FA_READ); //Open fileif(retFLASH == FR_OK){printf("\r\nFile open successful\r\n");retFLASH = f_read( &file, (void *)rBuffer, sizeof(rBuffer), &bytesread); //Read dataif(retFLASH == FR_OK){printf("\r\nFile read successful\r\n");PY_Delay_us_t(200000);FLASH_Read_Size = sizeof(rBuffer);for(uint16_t i = 0;i < FLASH_Read_Size;i++){printf("%d ", rBuffer[i]);}printf("\r\n");}else{printf("\r\nFile read error: %d\r\n", retFLASH);}f_close(&file); //Close file}else{printf("\r\nFile open error: %d\r\n", retFLASH);}}}else if(cmd==5) //File locating write{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open( &file, filepath, FA_CREATE_ALWAYS | FA_WRITE);  //Open or create fileif(retFLASH == FR_OK){printf("\r\nFile open or creation successful\r\n");retFLASH=f_lseek( &file, f_tell(&file) + sizeof(WBuffer) ); //move file operation pointer, f_tell(&file) gets file head locatingif(retFLASH == FR_OK){retFLASH = f_write( &file, (const void *)WBuffer, sizeof(WBuffer), &byteswritten);if(retFLASH == FR_OK){printf("\r\nFile locating write successful\r\n");}else{printf("\r\nFile locating write error: %d\r\n", retFLASH);}}else{printf("\r\nFile pointer error: %d\r\n",retFLASH);}f_close(&file);   //Close file}else{printf("\r\nFile open or creation error %d\r\n",retFLASH);}}}else if(cmd==6) //File locating read{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open(&file, filepath, FA_OPEN_EXISTING | FA_READ); //Open fileif(retFLASH == FR_OK){printf("\r\nFile open successful\r\n");retFLASH =  f_lseek(&file,f_tell(&file)+ sizeof(WBuffer)/2); //move file operation pointer, f_tell(&file) gets file head locatingif(retFLASH == FR_OK){retFLASH = f_read( &file, (void *)rBuffer, sizeof(rBuffer), &bytesread);if(retFLASH == FR_OK){printf("\r\nFile locating read successful\r\n");PY_Delay_us_t(200000);FLASH_Read_Size = sizeof(rBuffer);for(uint16_t i = 0;i < FLASH_Read_Size;i++){printf("%d ",rBuffer[i]);}printf("\r\n");}else{printf("\r\nFile locating read error: %d\r\n",retFLASH);}}else{printf("\r\nFile pointer error: %d\r\n",retFLASH);}f_close(&file);}else{printf("\r\nFile open error: %d\r\n",retFLASH);}}}/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** @brief System Clock Configuration* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};/** Supply configuration update enable*/HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);/** Configure the main internal regulator output voltage*/__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {}__HAL_RCC_SYSCFG_CLK_ENABLE();__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0);while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {}/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;RCC_OscInitStruct.HSIState = RCC_HSI_DIV1;RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;RCC_OscInitStruct.PLL.PLLM = 4;RCC_OscInitStruct.PLL.PLLN = 60;RCC_OscInitStruct.PLL.PLLP = 2;RCC_OscInitStruct.PLL.PLLQ = 2;RCC_OscInitStruct.PLL.PLLR = 2;RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_3;RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOWIDE;RCC_OscInitStruct.PLL.PLLFRACN = 0;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2|RCC_CLOCKTYPE_D3PCLK1|RCC_CLOCKTYPE_D1PCLK1;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2;RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2;RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK){Error_Handler();}
}/*** @brief QUADSPI Initialization Function* @param None* @retval None*/
static void MX_QUADSPI_Init(void)
{/* USER CODE BEGIN QUADSPI_Init 0 *//* USER CODE END QUADSPI_Init 0 *//* USER CODE BEGIN QUADSPI_Init 1 *//* USER CODE END QUADSPI_Init 1 *//* QUADSPI parameter configuration*/hqspi.Instance = QUADSPI;hqspi.Init.ClockPrescaler = 9;hqspi.Init.FifoThreshold = 4;hqspi.Init.SampleShifting = QSPI_SAMPLE_SHIFTING_HALFCYCLE;hqspi.Init.FlashSize = 25;hqspi.Init.ChipSelectHighTime = QSPI_CS_HIGH_TIME_5_CYCLE;hqspi.Init.ClockMode = QSPI_CLOCK_MODE_0;hqspi.Init.FlashID = QSPI_FLASH_ID_1;hqspi.Init.DualFlash = QSPI_DUALFLASH_DISABLE;if (HAL_QSPI_Init(&hqspi) != HAL_OK){Error_Handler();}/* USER CODE BEGIN QUADSPI_Init 2 *//* USER CODE END QUADSPI_Init 2 */}/*** @brief USART1 Initialization Function* @param None* @retval None*/
static void MX_USART1_UART_Init(void)
{/* USER CODE BEGIN USART1_Init 0 *//* USER CODE END USART1_Init 0 *//* USER CODE BEGIN USART1_Init 1 *//* USER CODE END USART1_Init 1 */huart1.Instance = USART1;huart1.Init.BaudRate = 115200;huart1.Init.WordLength = UART_WORDLENGTH_8B;huart1.Init.StopBits = UART_STOPBITS_1;huart1.Init.Parity = UART_PARITY_NONE;huart1.Init.Mode = UART_MODE_TX_RX;huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;huart1.Init.OverSampling = UART_OVERSAMPLING_16;huart1.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;huart1.Init.ClockPrescaler = UART_PRESCALER_DIV1;huart1.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;if (HAL_UART_Init(&huart1) != HAL_OK){Error_Handler();}if (HAL_UARTEx_SetTxFifoThreshold(&huart1, UART_TXFIFO_THRESHOLD_1_8) != HAL_OK){Error_Handler();}if (HAL_UARTEx_SetRxFifoThreshold(&huart1, UART_RXFIFO_THRESHOLD_1_8) != HAL_OK){Error_Handler();}if (HAL_UARTEx_DisableFifoMode(&huart1) != HAL_OK){Error_Handler();}/* USER CODE BEGIN USART1_Init 2 *//* USER CODE END USART1_Init 2 */}/*** @brief GPIO Initialization Function* @param None* @retval None*/
static void MX_GPIO_Init(void)
{/* GPIO Ports Clock Enable */__HAL_RCC_GPIOE_CLK_ENABLE();__HAL_RCC_GPIOB_CLK_ENABLE();__HAL_RCC_GPIOD_CLK_ENABLE();__HAL_RCC_GPIOA_CLK_ENABLE();}/* USER CODE BEGIN 4 */
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)
{if(huart==&huart1){cmd = uart1_rx[0];HAL_UART_Receive_IT(&huart1, uart1_rx, 1);}}
/* USER CODE END 4 *//*** @brief  This function is executed in case of error occurrence.* @retval None*/
void Error_Handler(void)
{/* USER CODE BEGIN Error_Handler_Debug *//* User can add his own implementation to report the HAL error return state */__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef  USE_FULL_ASSERT
/*** @brief  Reports the name of the source file and the source line number*         where the assert_param error has occurred.* @param  file: pointer to the source file name* @param  line: assert_param error line source number* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

STM32例程测试

串口指令0x01测试效果如下：
在这里插入图片描述
串口指令0x02测试效果如下：
在这里插入图片描述
串口指令0x03测试效果如下：
在这里插入图片描述
串口指令0x04测试效果如下：
在这里插入图片描述
串口指令0x05测试效果如下：
在这里插入图片描述
串口指令0x06测试效果如下：
在这里插入图片描述

STM32例程下载

STM32H750VBT6 QSPI总线FATS文件读写FLASH W25QXX例程下载

–End–

本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若转载，请注明出处：http://www.mzph.cn/news/705026.shtml

如若内容造成侵权/违法违规/事实不符，请联系多彩编程网进行投诉反馈email:809451989@qq.com，一经查实，立即删除！

相关文章

第十三天-mysql交互

第十三天-mysql交互

目录 1.安装MySQL connector 方式1&#xff1a;直接安装 方式2&#xff1a;下载 2.创建链接 3.游标Cursor 4.事务控制 5. 数据库连接池 1. 使用 6.循环执行SQL语句 不了解mysql的可以先了解mysql基础 1.安装MySQL connector 1. MySQL connector 是MySQL官方驱动模块…
阅读更多...
jmeter 按线程数阶梯式压测数据库

jmeter 按线程数阶梯式压测数据库

当前版本&#xff1a; jmeter 5.6.3mysql 5.7.39 简介 JMeter 通过 bzm - Concurrency Thread Group 来实现阶梯式压测&#xff0c;它并不是JMeter的官方插件&#xff0c;而是一种由Blazemeter提供的高级线程组插件。可以在不同的时间内并发执行不同数量的线程&#xff0c;模拟…
阅读更多...
音频常用测试参数

音频常用测试参数

一、总谐波失真&#xff08;THDN&#xff09; 总谐波失真指音频信号源通过功率放大器时&#xff0c;由于非线性元件所引起的输出信号比输入信号多出的额外谐波成份。谐波失真是由于系统不是完全线性造成的&#xff0c;我们用新增加总谐波成份的均方根与原来信号有效值的百分比来…
阅读更多...
MySQL之Pt-kill工具

MySQL之Pt-kill工具

工具下载 [rootlocalhost1 bin]# wget percona.com/get/percona-toolkit.tar.gz [rootlocalhost1 bin]# yum install perl-DBI [rootlocalhost1 bin]# yum install perl-DBD-MySQL [rootlocalhost1 bin]# ./pt-kill --help1、每10秒检查一次&#xff0c;发现有 Query 的进程就…
阅读更多...
3D生成式AI模型与工具

3D生成式AI模型与工具

当谈到技术炒作时&#xff0c;人工智能正在超越虚拟世界&#xff0c;吸引世界各地企业和消费者的注意力。 但人工智能可以进一步增强虚拟世界&#xff0c;至少在某种意义上&#xff1a;资产创造。 AI 有潜力扩大用于虚拟环境的 3D 资产的创建。 AI 3D生成使用人工智能生成3D模…
阅读更多...
开发知识点-.netC#图形用户界面开发之WPF

开发知识点-.netC#图形用户界面开发之WPF

C#图形用户界面开发 NuGet框架简介WinForms（Windows Forms）：WPF（Windows Presentation Foundation）：UWP（Universal Windows Platform）：MAUI（Multi-platform App UI）：选择控件参考文章随笔分类 - WPF入门基础教程系列
阅读更多...
什么时候要用到Reflect API？

什么时候要用到Reflect API？

参考文档 https://www.zhihu.com/question/460133198 https://cn.vuejs.org/guide/extras/reactivity-in-depth.html https://juejin.cn/post/7103764386220769311 Reflect API 一般搭配 Proxy API 一起使用。什么是 Proxy API 呢&#xff1f; 先回顾下 vue 的数据响应性是如何…
阅读更多...
GDB之(3)加载指定动态库文件

GDB之(3)加载指定动态库文件

GDB之(3)加载指定动态库文件 Author&#xff1a;Once Day Date&#xff1a;2024年2月26日 漫漫长路&#xff0c;才刚刚开始… 全系列文章请查看专栏: Linux实践记录_Once-Day的博客-CSDN博客 推荐参考文档&#xff1a; gdb 查找动态库方法_info sharedlibrary-CSDN博客GDB…
阅读更多...
服务器权限：Error: EACCES: permission denied, open‘/Cardiac/uniquC.csv

服务器权限：Error: EACCES: permission denied, open‘/Cardiac/uniquC.csv

背景&#xff1a; 我想在服务器上传一个文件uniquC.csv&#xff0c;但是服务器说我没有权限 解决方案&#xff1a; 1. 查看目前是否存在对文件夹的权限 ls -ld /Cardiac/ # your fold path 此时&#xff0c;我发现 这也意味着root也没有赋予写的权限。 2. 拿到root权限 …
阅读更多...
Kotlin多线程

Kotlin多线程

目录 线程的使用 线程的创建 例一&#xff1a;创建线程并输出Hello World Thread对象的用法 start() join() interrupt() 线程安全 原子性 可见性 有序性 线程锁 ReentrantLock ReadWriteLock 线程的使用 Java虚拟机中的多线程可以1:1映射至CPU中&#xff0c;即…
阅读更多...
ARM 版银河麒麟桌面系统下 Qt 开发环境搭建指南

ARM 版银河麒麟桌面系统下 Qt 开发环境搭建指南

目录 前言安装Linux ARM 版 QtCreator配置 Qt Creator配置构建套件 第一个麒麟 Qt 应用程序小结 前言 在上一篇文章信创ARM架构QT应用开发环境搭建中建议大家使用 Ubuntu X86 系统作为信创 ARM 架构 QT 应用的开发环境&#xff0c;里面使用了交叉编译的方式。这对于自己的 Qt …
阅读更多...
vue3 + vite + ts 中使用less文件全局变量

vue3 + vite + ts 中使用less文件全局变量

文章目录 安装依赖新建css变量文件全局引入css变量文件使用css变量 一、安装依赖 npm install less less-loader --save-dev 二、新建CSS变量文件 (1) :在根目录下的src文件中 src-> asset -> css ->glibal.less // glibal.less :root{--public_background_font_Col…
阅读更多...
Dubbo知识点大全

Dubbo知识点大全

“ 分布式应用场景有高并发，高可扩展和高性能的要求。还涉及到，序列化/反序列化，网络，多线程以及设计模式的问题。幸好 Dubbo 框架将上述知识进行了封装，让程序员能够把注意力放到业务上。 概念和架构 Provider：暴露服务的服务提供方Consumer：调用远程服务消费方Regist…
阅读更多...
CUDA编程 - 用向量化访存优化 elementwise 核函数 - 学习记录

CUDA编程 - 用向量化访存优化 elementwise 核函数 - 学习记录

Cuda elementwise 一、简介1.1、ElementWise1.2、 float4 - 向量化访存 二、实践2.1、如何使用向量化访存2.2、Cuda elementwise - Add2.3、Cuda elementwise - Sigmoid2.3.1、简单的 Sigmoid 函数2.3.2、ElementWise Sigmoid float4&#xff08;向量化访存&#xff09; 2.4、C…
阅读更多...
商家入驻平台怎么让资金自动分配给商家

商家入驻平台怎么让资金自动分配给商家

最近很多上线了多商户电商系统的朋友咨询&#xff0c;我们平台的用户支付后&#xff0c;钱进入了我们的对公账户&#xff0c;怎样让钱在走完流程后&#xff0c;自动进入商家的账户呢&#xff1f;今天商淘云为您分享商户入驻平台自动分配给商家资金的三种方法。 首先是平台应建立…
阅读更多...
Docker基础（一）

Docker基础（一）

文章目录 1. 基础概念2. 安装docker3. docker常用命令3.1 帮助命令3.2 镜像命令3.3 容器命令3.4 其他命令 4. 使用案例 1. 基础概念 镜像&#xff08;Image&#xff09;&#xff1a;Docker 镜像&#xff08;Image&#xff09;&#xff0c;就相当于是一个 root 文件系统。比如官…
阅读更多...
node14下运行项目报错：regeneratorRuntime is not defined

node14下运行项目报错：regeneratorRuntime is not defined

regeneratorRuntime is not defined&#xff0c;这是由于配置babel出错问题&#xff0c;由于使用了es7语法如async/await而当前babel版本过低 解决&#xff1a; npm install -D babel-plugin-transform-runtime babel-runtime 安装完成后在.babelrc文件下配置&#xff1a; &qu…
阅读更多...
远程连接Redis

远程连接Redis

以连接阿里云上的Redis为例 1. 在阿里云安全组中开放端口 2.修改Redis启动时所用的配置文件&#xff08;redis.conf&#xff09; 2.1 修改ip地址 如图&#xff1a;将默认的本地ip bind 127.0.0.1地址改为bind 0.0.0.0 2.2 将保护模式关闭 将默认的 supervised yes 改为 n…
阅读更多...
Transformer视频理解学习的笔记

Transformer视频理解学习的笔记

今天复习了Transformer,ViT, 学了SwinTransformer, 还有观看了B站视频理解沐神系列串讲视频上&#xff08;24.2.26未看完,明天接着看&#xff09; 这里面更多论文见&#xff1a;https://github.com/mli/paper-reading/ B站视频理解沐神系列串讲视频下&#xff08;明天接着看&a…
阅读更多...
认证模式~

认证模式~

认证方式 基于Cookie和Session的认证方式 基于Cookie和Session的认证是传统的Web应用认证机制。它依赖于HTTP协议无状态的特性&#xff0c;在客户端&#xff08;浏览器&#xff09;和服务器之间保持用户的状态。 工作原理 用户登录&#xff1a;用户通过输入用户名和密码来登…
阅读更多...
推荐文章
最新文章

Copyright @ 2022~2023