linux 网卡配置 vlan/bond/bridge/macvlan/ipvlan 模式

linux 网卡模式

linux网卡支持非vlan模式、vlan模式、bond模式、bridge模式，macvlan模式、ipvlan模式等，下面介绍交换机端及服务器端配置示例。

前置要求：

  • 准备一台物理交换机，以 H3C S5130 三层交换机为例
  • 准备一台物理服务器，以 Ubuntu 22.04 LTS 操作系统为例

交换机创建2个示例VLAN，vlan10和vlan20，及VLAN接口。

<H3C>system-view[H3C]vlan 10 20[H3C]interface Vlan-interface 10
[H3C-Vlan-interface10]ip address 172.16.10.1 24
[H3C-Vlan-interface10]undo shutdown
[H3C-Vlan-interface10]exit
[H3C][H3C]interface Vlan-interface 20
[H3C-Vlan-interface20]ip address 172.16.20.1 24
[H3C-Vlan-interface20]undo  shutdown 
[H3C-Vlan-interface20]exit
[H3C]

网卡非vlan模式

网卡非vlan模式，一般直接配置IP地址，对端上连交换机配置为access口，access口一般用于连接纯物理服务器或办公终端设备。

示意图如下
在这里插入图片描述

交换机配置，交换机接口配置为access模式，并加入对应vlan

<H3C>system-view
[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]port link-type access
[H3C-GigabitEthernet1/0/1]port access vlan 10
[H3C-GigabitEthernet1/0/1]exit
[H3C]
[H3C]interface GigabitEthernet 1/0/2
[H3C-GigabitEthernet1/0/2]port link-type access
[H3C-GigabitEthernet1/0/2]port access vlan 20
[H3C-GigabitEthernet1/0/2]exit
[H3C]

服务器1配置，服务器网卡直接配置IP地址

root@server1:~# cat /etc/netplan/00-installer-config.yaml
network:ethernets:enp1s0:dhcp4: falseaddresses:- 172.16.10.10/24nameservers:addresses:- 223.5.5.5- 223.6.6.6routes:- to: defaultvia: 172.16.10.1version: 2

服务器2配置，服务器网卡直接配置IP地址

root@server2:~# cat /etc/netplan/00-installer-config.yaml
network:ethernets:enp1s0:dhcp4: falseaddresses:- 172.16.20.10/24nameservers:addresses:- 223.5.5.5- 223.6.6.6routes:- to: defaultvia: 172.16.20.1version: 2

应用网卡配置

netplan apply

查看服务器接口信息

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global enp1s0valid_lft forever preferred_lft foreverinet6 fe80::7eb5:9bff:fe59:a71/64 scope link valid_lft forever preferred_lft forever

通过server1 ping server2测试连通性，三层交换机支持路由功能，能够打通二层隔离的vlan网段。

root@server1:~# ping 172.16.20.10 -c 4
PING 172.16.20.10 (172.16.20.10) 56(84) bytes of data.
64 bytes from 172.16.20.10: icmp_seq=1 ttl=64 time=0.033 ms
64 bytes from 172.16.20.10: icmp_seq=2 ttl=64 time=0.048 ms
64 bytes from 172.16.20.10: icmp_seq=3 ttl=64 time=0.048 ms
64 bytes from 172.16.20.10: icmp_seq=4 ttl=64 time=0.047 ms--- 172.16.20.10 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3061ms
rtt min/avg/max/mdev = 0.033/0.044/0.048/0.006 ms

网卡vlan模式

vlan模式下，对端上连交换机需要配置为trunk口，允许多个vlan通过。

示意图如下
在这里插入图片描述

交换机配置，交换机需要配置为trunk口，允许多个vlan通过

H3C>system-view 
[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]port link-type trunk
[H3C-GigabitEthernet1/0/1]port trunk permit vlan 10 20
[H3C-GigabitEthernet1/0/1]exit
[H3C]

服务器配置，服务器需要配置vlan子接口

root@server1:~# cat /etc/netplan/00-installer-config.yaml
network:ethernets:enp1s0:dhcp4: truevlans:vlan10:id: 10link: enp1s0addresses: [ "172.16.10.10/24" ]routes:- to: defaultvia: 172.16.10.1metric: 200vlan20:id: 20link: enp1s0addresses: [ "172.16.20.10/24" ]routes:- to: defaultvia: 172.16.20.1metric: 300version: 2

查看接口信息，新建了两个vlan子接口vlan10和vlan20

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet6 fe80::7eb5:9bff:fe59:a71/64 scope link valid_lft forever preferred_lft forever
10: vlan10@enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global vlan10valid_lft forever preferred_lft foreverinet6 fe80::7eb5:9bff:fe59:a71/64 scope link valid_lft forever preferred_lft forever
11: vlan20@enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet 172.16.20.10/24 brd 172.16.20.255 scope global vlan20valid_lft forever preferred_lft foreverinet6 fe80::7eb5:9bff:fe59:a71/64 scope link valid_lft forever preferred_lft forever

通过vlan10 和 vlan20测试与网关连通性

root@server1:~# ping 172.16.10.1 -c 4
PING 172.16.10.1 (172.16.10.1) 56(84) bytes of data.
64 bytes from 172.16.10.1: icmp_seq=1 ttl=64 time=0.033 ms
64 bytes from 172.16.10.1: icmp_seq=2 ttl=64 time=0.048 ms
64 bytes from 172.16.10.1: icmp_seq=3 ttl=64 time=0.048 ms
64 bytes from 172.16.10.1: icmp_seq=4 ttl=64 time=0.047 ms--- 172.16.10.1 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3061ms
rtt min/avg/max/mdev = 0.033/0.044/0.048/0.006 ms
root@server1:~#
root@server1:~# ping 172.16.20.1 -c 4
PING 172.16.20.1 (172.16.20.1) 56(84) bytes of data.
64 bytes from 172.16.20.1: icmp_seq=1 ttl=64 time=0.033 ms
64 bytes from 172.16.20.1: icmp_seq=2 ttl=64 time=0.048 ms
64 bytes from 172.16.20.1: icmp_seq=3 ttl=64 time=0.048 ms
64 bytes from 172.16.20.1: icmp_seq=4 ttl=64 time=0.047 ms--- 172.16.20.1 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3061ms
rtt min/avg/max/mdev = 0.033/0.044/0.048/0.006 ms

网卡bond模式

bond模式下，对端交换机需要配置bond聚合口。

示意图如下
在这里插入图片描述

交换机配置，配置动态链路聚合，将端口g1/0/1和g1/0/3加入聚合组。然后将bond口配置为trunk模式。

<H3C>system-view
[H3C]interface Bridge-Aggregation 1
[H3C-Bridge-Aggregation1]link-aggregation mode dynamic
[H3C-Bridge-Aggregation1]quit[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]port link-aggregation group 1
[H3C-GigabitEthernet1/0/1]exit[H3C]interface GigabitEthernet 1/0/3
[H3C-GigabitEthernet1/0/3]port link-aggregation group 1
[H3C-GigabitEthernet1/0/3]exit[H3C]interface Bridge-Aggregation 1
[H3C-Bridge-Aggregation1]port link-type trunk
[H3C-Bridge-Aggregation1]port trunk permit vlan 10 20
[H3C-Bridge-Aggregation1]exit

服务器配置

root@server1:~# cat /etc/netplan/00-installer-config.yaml
network:version: 2ethernets:enp1s0:dhcp4: noenp2s0:dhcp4: nobonds:bond0:interfaces:- enp1s0- enp2s0parameters:mode: 802.3adlacp-rate: fastmii-monitor-interval: 100transmit-hash-policy: layer2+3vlans:vlan10:id: 10link: bond0addresses: [ "172.16.10.10/24" ]routes:- to: defaultvia: 172.16.10.1metric: 200vlan20:id: 20link: bond0addresses: [ "172.16.20.10/24" ]routes:- to: defaultvia: 172.16.20.1metric: 300

查看网卡信息，新建了bond0网口，并且基于bond0网口创建了两个vlan子接口vlan10和vlan20，enp1s0和enp2s0显示master bond0，说明两个网卡属于bond0成员接口。

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc fq_codel master bond0 state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ff permaddr 7c:b5:9b:59:0a:71
3: enp2s0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc fq_codel master bond0 state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ff permaddr e4:54:e8:dc:e5:88
7: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ffinet6 fe80::acfd:60ff:fe48:841a/64 scope link valid_lft forever preferred_lft forever
8: vlan10@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global vlan10valid_lft forever preferred_lft foreverinet6 fe80::acfd:60ff:fe48:841a/64 scope link valid_lft forever preferred_lft forever
9: vlan20@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ffinet 172.16.20.10/24 brd 172.16.20.255 scope global vlan20valid_lft forever preferred_lft foreverinet6 fe80::acfd:60ff:fe48:841a/64 scope link valid_lft forever preferred_lft forever

查看bond状态，Bonding Mode显示为IEEE 802.3ad Dynamic link aggregation，并且下面Slave Interface显示了两个成员接口的信息。

root@server1:~# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v5.15.0-60-genericBonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Peer Notification Delay (ms): 0802.3ad info
LACP active: on
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
System priority: 65535
System MAC address: ae:fd:60:48:84:1a
Active Aggregator Info:Aggregator ID: 1Number of ports: 2Actor Key: 9Partner Key: 1Partner Mac Address: fc:60:9b:35:ad:18Slave Interface: enp1s0
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 2
Permanent HW addr: 7c:b5:9b:59:0a:71
Slave queue ID: 0
Aggregator ID: 1
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:system priority: 65535system mac address: ae:fd:60:48:84:1aport key: 9port priority: 255port number: 1port state: 63
details partner lacp pdu:system priority: 32768system mac address: fc:60:9b:35:ad:18oper key: 1port priority: 32768port number: 2port state: 61Slave Interface: enp2s0
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 3
Permanent HW addr: e4:54:e8:dc:e5:88
Slave queue ID: 0
Aggregator ID: 1
Actor Churn State: none
Partner Churn State: none
Actor Churned Count: 0
Partner Churned Count: 0
details actor lacp pdu:system priority: 65535system mac address: ae:fd:60:48:84:1aport key: 9port priority: 255port number: 2port state: 63
details partner lacp pdu:system priority: 32768system mac address: fc:60:9b:35:ad:18oper key: 1port priority: 32768port number: 1port state: 61

测试连通性，测试与交换机网关地址的连通性：

root@server1:~# ping 172.16.10.1 -c 4
PING 172.16.10.1 (172.16.10.1) 56(84) bytes of data.
64 bytes from 172.16.10.1: icmp_seq=1 ttl=255 time=1.64 ms
64 bytes from 172.16.10.1: icmp_seq=2 ttl=255 time=1.59 ms
64 bytes from 172.16.10.1: icmp_seq=3 ttl=255 time=1.95 ms
64 bytes from 172.16.10.1: icmp_seq=4 ttl=255 time=1.93 ms--- 172.16.10.1 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3006ms
rtt min/avg/max/mdev = 1.589/1.776/1.953/0.165 ms
root@server1:~#

关闭一个接口，再次测试连通性，依然能够ping通

root@server1:~# ip link set dev enp2s0 down
root@server1:~# ip link show enp2s0
3: enp2s0: <BROADCAST,MULTICAST,SLAVE> mtu 1500 qdisc fq_codel master bond0 state DOWN mode DEFAULT group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ff permaddr e4:54:e8:dc:e5:88
root@server1:~# 
root@server1:~# ping 172.16.10.1 -c 4
PING 172.16.10.1 (172.16.10.1) 56(84) bytes of data.
64 bytes from 172.16.10.1: icmp_seq=1 ttl=255 time=1.54 ms
64 bytes from 172.16.10.1: icmp_seq=2 ttl=255 time=1.64 ms
64 bytes from 172.16.10.1: icmp_seq=3 ttl=255 time=2.73 ms
64 bytes from 172.16.10.1: icmp_seq=4 ttl=255 time=1.47 ms--- 172.16.10.1 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3006ms
rtt min/avg/max/mdev = 1.470/1.844/2.732/0.516 ms

网卡桥接模式

桥接模式下，对端交换机可配置access模式或trunk模式。

示意图如下

在这里插入图片描述

交换机配置，交换机接口配置为access模式为例，并加入对应vlan

<H3C>system-view
[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]port link-type access
[H3C-GigabitEthernet1/0/1]port access vlan 10
[H3C-GigabitEthernet1/0/1]exit
[H3C]

服务器配置，物理网卡加入到网桥中，IP地址配置到网桥接口br0上。

root@server1:~# cat /etc/netplan/00-installer-config.yaml
network:version: 2ethernets:enp1s0:dhcp4: nodhcp6: nobridges:br0:interfaces: [enp1s0]addresses: [172.16.10.10/24]routes:- to: defaultvia: 172.16.10.1metric: 100on-link: truemtu: 1500nameservers:addresses:- 223.5.5.5- 223.6.6.6parameters:stp: trueforward-delay: 4

查看网卡信息

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br0 state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ff
12: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether 0e:d0:7e:31:9c:74 brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global br0valid_lft forever preferred_lft foreverinet6 fe80::cd0:7eff:fe31:9c74/64 scope link valid_lft forever preferred_lft forever

查看网桥及接口，当前网桥上只有一个物理接口enp1s0。

root@server1:~# apt install -y bridge-utils
root@ubuntu:~# brctl show
bridge name     bridge id               STP enabled     interfaces
br0             8000.0ed07e319c74       yes             enp1s0
root@server1:~#

这样在KVM虚拟化环境，虚拟机实例连接到网桥后，虚拟机可以配置与物理网卡相同网段的IP地址。访问虚拟机可以像访问物理机一样方便。

网卡macvlan模式

macvlan(MAC Virtual LAN)是Linux内核提供的一种网络虚拟化技术，它允许在一个物理网卡接口上创建多个虚拟网卡接口，每个虚拟接口都有自己独立的MAC地址，也可以配置上 IP 地址进行通信。Macvlan 下的虚拟机或者容器网络和主机在同一个网段中，共享同一个广播域。

macvlan模式下，对端交换机可配置access模式或trunk模式，trunk模式下macvlan能够与vlan很好的结合使用。

示意图如下：

在这里插入图片描述

macvlan IP模式

该模式下，上连交换机接口配置为access模式，服务器macvlan主网卡和子接口直接配置相同网段的IP地址。

交换机配置

<H3C>system-view
[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]port link-type access
[H3C-GigabitEthernet1/0/1]port access vlan 10
[H3C-GigabitEthernet1/0/1]exit

服务器配置，macvlan支持多种模式，这里使用bridge模式，并持久化配置

cat >/etc/networkd-dispatcher/routable.d/10-macvlan-interfaces.sh<<EOF
#! /bin/bash
ip link add macvlan0 link enp1s0 type macvlan mode bridge
ip link add macvlan1 link enp1s0 type macvlan mode bridge
EOFchmod o+x,g+x,u+x /etc/networkd-dispatcher/routable.d/10-macvlan-interfaces.sh

配置netplan

root@server1:~# cat /etc/netplan/00-installer-config.yaml
network:ethernets:enp1s0:dhcp4: falseaddresses:- 172.16.10.10/24nameservers:addresses:- 223.5.5.5- 223.6.6.6routes:- to: defaultvia: 172.16.10.1macvlan0:addresses:- 172.16.10.11/24macvlan1:addresses:- 172.16.10.12/24version: 2

应用网卡配置

netplan apply

查看网卡信息，新建了两个macvlan接口，IP地址与主网卡位于同一网段，并且每个接口都有独立的MAC地址。

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global enp1s0valid_lft forever preferred_lft forever
13: macvlan0@enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether 32:e8:b4:0a:47:62 brd ff:ff:ff:ff:ff:ffinet 172.16.10.11/24 brd 172.16.10.255 scope global macvlan0valid_lft forever preferred_lft foreverinet6 fe80::30e8:b4ff:fe0a:4762/64 scope link valid_lft forever preferred_lft forever
14: macvlan1@enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether d2:73:75:14:b2:04 brd ff:ff:ff:ff:ff:ffinet 172.16.10.12/24 brd 172.16.10.255 scope global macvlan1valid_lft forever preferred_lft foreverinet6 fe80::d073:75ff:fe14:b204/64 scope link valid_lft forever preferred_lft forever

测试与网关的连通性

root@server1:~# ping -c 3 172.16.10.1
PING 172.16.10.1 (172.16.10.1) 56(84) bytes of data.
64 bytes from 172.16.10.1: icmp_seq=1 ttl=255 time=3.60 ms
64 bytes from 172.16.10.1: icmp_seq=2 ttl=255 time=1.45 ms
64 bytes from 172.16.10.1: icmp_seq=3 ttl=255 time=1.44 ms--- 172.16.10.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 1.441/2.163/3.602/1.017 ms
root@server1:~#

macvlan vlan模式

该模式下，上连交换机接口配置为trunk模式，服务器macvlan主网卡不配置IP地址，每个macvlan子接口配置为不同的vlan子接口。

交换机配置

<H3C>system-view
[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/3]port link-type trunk
[H3C-GigabitEthernet1/0/3]port trunk permit vlan 10 20
[H3C-GigabitEthernet1/0/1]exit
[H3C]

服务器配置，macvlan支持多种模式，这里使用bridge模式，并持久化配置

cat >/etc/networkd-dispatcher/routable.d/10-macvlan-interfaces.sh<<EOF
#! /bin/bash
ip link add macvlan0 link enp1s0 type macvlan mode bridge
ip link add macvlan1 link enp1s0 type macvlan mode bridge
EOFchmod o+x,g+x,u+x /etc/networkd-dispatcher/routable.d/10-macvlan-interfaces.sh

配置netplan，两个macvlan接口macvlan0和macvlan1分别配置vlan子接口vlan10和vlan20。

root@ubuntu:~# cat /etc/netplan/00-installer-config.yaml
network:ethernets:enp1s0:dhcp4: falsemacvlan0:dhcp4: falsemacvlan1:dhcp4: falsevlans:vlan10:id: 10link: macvlan0addresses: [ "172.16.10.10/24" ]routes:- to: defaultvia: 172.16.10.1metric: 200vlan20:id: 20link: macvlan1addresses: [ "172.16.20.10/24" ]routes:- to: defaultvia: 172.16.20.1metric: 300version: 2

应用网卡配置

netplan apply

查看网卡信息，新建了两个macvlan接口，以及对应的两个vlan子接口。

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet6 fe80::7eb5:9bff:fe59:a71/64 scope link valid_lft forever preferred_lft forever
11: macvlan0@enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether 32:e8:b4:0a:47:62 brd ff:ff:ff:ff:ff:ffinet6 fe80::30e8:b4ff:fe0a:4762/64 scope link valid_lft forever preferred_lft forever
12: macvlan1@enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether d2:73:75:14:b2:04 brd ff:ff:ff:ff:ff:ffinet6 fe80::d073:75ff:fe14:b204/64 scope link valid_lft forever preferred_lft forever
13: vlan10@macvlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether 32:e8:b4:0a:47:62 brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global vlan10valid_lft forever preferred_lft foreverinet6 fe80::30e8:b4ff:fe0a:4762/64 scope link valid_lft forever preferred_lft forever
14: vlan20@macvlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether d2:73:75:14:b2:04 brd ff:ff:ff:ff:ff:ffinet 172.16.20.10/24 brd 172.16.20.255 scope global vlan20valid_lft forever preferred_lft foreverinet6 fe80::d073:75ff:fe14:b204/64 scope link valid_lft forever preferred_lft forever

测试两个VLAN接口与外部网关的连通性

root@server1:~# ping -c 3 172.16.10.1
PING 172.16.10.1 (172.16.10.1) 56(84) bytes of data.
64 bytes from 172.16.10.1: icmp_seq=1 ttl=255 time=3.60 ms
64 bytes from 172.16.10.1: icmp_seq=2 ttl=255 time=1.45 ms
64 bytes from 172.16.10.1: icmp_seq=3 ttl=255 time=1.44 ms--- 172.16.10.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 1.441/2.163/3.602/1.017 ms
root@server1:~# 
root@server1:~# ping -c 3 172.16.20.1 
PING 172.16.20.1 (172.16.20.1) 56(84) bytes of data.
64 bytes from 172.16.20.1: icmp_seq=1 ttl=255 time=1.35 ms
64 bytes from 172.16.20.1: icmp_seq=2 ttl=255 time=1.48 ms
64 bytes from 172.16.20.1: icmp_seq=3 ttl=255 time=1.46 ms--- 172.16.20.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 1.353/1.429/1.477/0.054 ms
root@server1:~#

网卡ipvlan模式

IPVLAN(IP Virtual LAN)是Linux内核提供的一种网络虚拟化技术，它可以在一个物理网卡上创建多个虚拟网卡接口，每个虚拟接口都有自己独立的IP地址。

IPVLAN和macvlan类似，都是从一个主机接口虚拟出多个虚拟网络接口。唯一比较大的区别就是ipvlan虚拟出的子接口都有相同的mac地址（与物理接口共用同个mac地址），但可配置不同的ip地址。

ipvlan模式下，对端交换机也可以配置access模式或trunk模式，trunk模式下ipvlan能够与vlan很好的结合使用。

示意图如下
在这里插入图片描述

交换机配置

<H3C>system-view
[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]port link-type access
[H3C-GigabitEthernet1/0/1]port access vlan 10
[H3C-GigabitEthernet1/0/1]exit
[H3C]

服务器配置，ipvlan支持三种模式(l2、l3、l3s)，这里使用l3模式，并持久化配置

cat >/etc/networkd-dispatcher/routable.d/10-ipvlan-interfaces.sh<<EOF
#! /bin/bash
ip link add ipvlan0 link enp1s0 type ipvlan mode l3
ip link add ipvlan1 link enp1s0 type ipvlan mode l3
EOF
chmod o+x,g+x,u+x /etc/networkd-dispatcher/routable.d/10-ipvlan-interfaces.sh

配置netplan

root@server1:~# cat /etc/netplan/00-installer-config.yaml
network:ethernets:enp1s0:dhcp4: falseaddresses:- 172.16.10.10/24nameservers:addresses:- 223.5.5.5- 223.6.6.6routes:- to: defaultvia: 172.16.10.1ipvlan0:addresses:- 172.16.10.11/24ipvlan1:addresses:- 172.16.10.12/24version: 2

应用网卡配置

netplan apply

查看网卡信息，新建了两ipvlan接口，IP地址与主网卡位于同一网段，并且每个接口都有与主网卡相同的MAC地址。

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global enp1s0valid_lft forever preferred_lft foreverinet6 fe80::7eb5:9bff:fe59:a71/64 scope link valid_lft forever preferred_lft forever
9: ipvlan0@enp1s0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet 172.16.10.11/24 brd 172.16.10.255 scope global ipvlan0valid_lft forever preferred_lft foreverinet6 fe80::7cb5:9b00:159:a71/64 scope link valid_lft forever preferred_lft forever
10: ipvlan1@enp1s0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000link/ether 7c:b5:9b:59:0a:71 brd ff:ff:ff:ff:ff:ffinet 172.16.10.12/24 brd 172.16.10.255 scope global ipvlan1valid_lft forever preferred_lft foreverinet6 fe80::7cb5:9b00:259:a71/64 scope link valid_lft forever preferred_lft forever

测试与网关的连通性

root@server1:~# ping -c 3 172.16.10.1
PING 172.16.10.1 (172.16.10.1) 56(84) bytes of data.
64 bytes from 172.16.10.1: icmp_seq=1 ttl=255 time=3.60 ms
64 bytes from 172.16.10.1: icmp_seq=2 ttl=255 time=1.45 ms
64 bytes from 172.16.10.1: icmp_seq=3 ttl=255 time=1.44 ms--- 172.16.10.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2004ms
rtt min/avg/max/mdev = 1.441/2.163/3.602/1.017 ms
root@server1:~#

bond、vlan与桥接混合配置

将服务器两块网卡组成bond口，在bond口之上创建两个vlan子接口，分别加入两个linux bridge中，然后在不同bridge下创建虚拟机，虚拟机将属于不同vlan。

示意图如下：
在这里插入图片描述
交换机配置，配置动态链路聚合，将端口g1/0/1和g1/0/3加入聚合组。然后将bond口配置为trunk模式。

<H3C>system-view
[H3C]interface Bridge-Aggregation 1
[H3C-Bridge-Aggregation1]link-aggregation mode dynamic
[H3C-Bridge-Aggregation1]quit[H3C]interface GigabitEthernet 1/0/1
[H3C-GigabitEthernet1/0/1]port link-aggregation group 1
[H3C-GigabitEthernet1/0/1]exit[H3C]interface GigabitEthernet 1/0/3
[H3C-GigabitEthernet1/0/3]port link-aggregation group 1
[H3C-GigabitEthernet1/0/3]exit[H3C]interface Bridge-Aggregation 1
[H3C-Bridge-Aggregation1]port link-type trunk
[H3C-Bridge-Aggregation1]port trunk permit vlan 10 20
[H3C-Bridge-Aggregation1]exit

服务器网卡配置

root@server1:~# cat /etc/netplan/00-installer-config.yaml
network:version: 2ethernets:enp1s0:dhcp4: noenp2s0:dhcp4: nobonds:bond0:interfaces:- enp1s0- enp2s0parameters:mode: 802.3adlacp-rate: fastmii-monitor-interval: 100transmit-hash-policy: layer2+3bridges:br10:interfaces: [ vlan10 ]br20:interfaces: [ vlan20 ]vlans:vlan10:id: 10link: bond0vlan20:id: 20link: bond0

查看网卡信息，新建了bond0网口，并且基于bond0网口创建了两个vlan子接口vlan10和vlan20。

root@server1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc fq_codel master bond0 state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ff permaddr 7c:b5:9b:59:0a:71
3: enp2s0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc fq_codel master bond0 state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ff permaddr e4:54:e8:dc:e5:88
15: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ffinet6 fe80::acfd:60ff:fe48:841a/64 scope link valid_lft forever preferred_lft forever
16: br10: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether ee:df:66:ab:c2:4b brd ff:ff:ff:ff:ff:ffinet6 fe80::ecdf:66ff:feab:c24b/64 scope link valid_lft forever preferred_lft forever
17: br20: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000link/ether 9e:4d:f4:0a:6d:13 brd ff:ff:ff:ff:ff:ffinet6 fe80::9c4d:f4ff:fe0a:6d13/64 scope link valid_lft forever preferred_lft forever
18: vlan10@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br10 state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ff
19: vlan20@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br20 state UP group default qlen 1000link/ether ae:fd:60:48:84:1a brd ff:ff:ff:ff:ff:ff

查看创建的网桥

root@server1:~# brctl show
bridge name     bridge id               STP enabled     interfaces
br10            8000.eedf66abc24b       no              vlan10
br20            8000.9e4df40a6d13       no              vlan20

在server1安装kvm虚拟化环境，然后创建两个新的kvm网络，分别绑定到不同网桥

cat >br10-network.xml<<EOF
<network><name>br10-net</name><forward mode="bridge"/><bridge name="br10"/>
</network>
EOF
cat >br20-network.xml<<EOF
<network><name>br20-net</name><forward mode="bridge"/><bridge name="br20"/>
</network>
EOFvirsh net-define br10-network.xml
virsh net-define br20-network.xml
virsh net-start br10-net
virsh net-start br20-net
virsh net-autostart br10-net
virsh net-autostart br20-net

查看新建的网络

root@server1:~# virsh net-listName       State    Autostart   Persistent
---------------------------------------------br10-net   active   yes         yesbr20-net   active   yes         yesdefault    active   yes         yes

创建两个虚拟机，指定使用不同网络

virt-install \--name vm1 \--vcpus 1 \--memory 2048 \--disk path=/var/lib/libvirt/images/vm1/jammy-server-cloudimg-amd64.img \--os-variant ubuntu22.04 \--import \--autostart \--noautoconsole \--network network=br10-netvirt-install \--name vm2 \--vcpus 1 \--memory 2048 \--disk path=/var/lib/libvirt/images/vm2/jammy-server-cloudimg-amd64.img \--os-variant ubuntu22.04 \--import \--autostart \--noautoconsole \--network network=br20-net

查看创建的虚拟机

root@server1:~# virsh listId   Name   State
----------------------13   vm1    running14   vm2    running

为vm1配置vlan10的IP地址

virsh console vm1
cat >/etc/netplan/00-installer-config.yaml<<EOF
network:ethernets:enp1s0:addresses:- 172.16.10.10/24nameservers:addresses:- 223.5.5.5routes:- to: defaultvia: 172.16.10.1version: 2
EOF
netplan apply

为vm2配置vlan20的IP地址

virsh console vm2
cat >/etc/netplan/00-installer-config.yaml<<EOF
network:ethernets:enp1s0:addresses:- 172.16.20.10/24nameservers:addresses:- 223.5.5.5routes:- to: defaultvia: 172.16.20.1version: 2
EOF
netplan apply

登录到vm1，测试vm1与外部网关连通性

root@vm1:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000link/ether 52:54:00:a4:aa:9d brd ff:ff:ff:ff:ff:ffinet 172.16.10.10/24 brd 172.16.10.255 scope global enp1s0valid_lft forever preferred_lft foreverinet6 fe80::5054:ff:fea4:aa9d/64 scope link valid_lft forever preferred_lft forever
root@vm1:~# 
root@vm1:~# ping 172.16.10.1 -c 3
PING 172.16.10.1 (172.16.10.1) 56(84) bytes of data.
64 bytes from 172.16.10.1: icmp_seq=1 ttl=255 time=1.51 ms
64 bytes from 172.16.10.1: icmp_seq=2 ttl=255 time=7.10 ms
64 bytes from 172.16.10.1: icmp_seq=3 ttl=255 time=2.10 ms--- 172.16.10.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2003ms
rtt min/avg/max/mdev = 1.505/3.568/7.101/2.509 ms
root@vm1:~#

登录到vm2，测试vm2与外部网关连通性

root@vm2:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00inet 127.0.0.1/8 scope host lovalid_lft forever preferred_lft foreverinet6 ::1/128 scope host valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000link/ether 52:54:00:89:61:da brd ff:ff:ff:ff:ff:ffinet 172.16.20.10/24 brd 172.16.20.255 scope global enp1s0valid_lft forever preferred_lft foreverinet6 fe80::5054:ff:fe89:61da/64 scope link valid_lft forever preferred_lft forever
root@vm2:~# 
root@vm2:~# ping 172.16.20.1 -c 3
PING 172.16.20.1 (172.16.20.1) 56(84) bytes of data.
64 bytes from 172.16.20.1: icmp_seq=1 ttl=255 time=1.73 ms
64 bytes from 172.16.20.1: icmp_seq=2 ttl=255 time=2.00 ms
64 bytes from 172.16.20.1: icmp_seq=3 ttl=255 time=2.00 ms--- 172.16.20.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2003ms
rtt min/avg/max/mdev = 1.732/1.911/2.003/0.126 ms
root@vm2:~#

本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若转载，请注明出处：http://www.mzph.cn/news/773618.shtml

如若内容造成侵权/违法违规/事实不符，请联系多彩编程网进行投诉反馈email:809451989@qq.com，一经查实，立即删除！

相关文章

AD域---共享文件夹-容量配额管理

AD域---共享文件夹-容量配额管理

域环境共享文件夹-容量配额管理 要求 1/李斯用户配额10G云盘空间&#xff0c;张珊用户配额30G云盘空间 2/D:\ 配额-启用配额-启用配额管理-拒绝将磁盘空间给超过配额限制的用户-勾选 3/将磁盘空间限制为:55GB&#xff0c;将警告等级设为50GB 4/选择该卷的配额记录选项-勾选…
阅读更多...
大型集团公司企业文化知识竞活动赛策划方案

大型集团公司企业文化知识竞活动赛策划方案

一场高端企业文化知识竞赛活动完整策划书&#xff0c;按诗词大会舞美标准进行设计&#xff0c;竞赛规则新颖&#xff0c;值得收藏。 天纵高端知识竞赛服务商&#xff0c;20多年现场经验和软硬件开发。 专业承办全国高端知识竞赛活动。线上线下各类竞赛活动均可执行&#xff0c;…
阅读更多...
鸿蒙开发之了解ArkTS

鸿蒙开发之了解ArkTS

鸿蒙开发者官网 &#xff1a; https://developer.huawei.com/consumer/cn/ 开发鸿蒙要用的软件是 DevEco Studio ArkTS建立在JS和TS的基础之上&#xff0c;扩展了声明式UI开发范式和状态管理&#xff0c;提供更简洁和自然的开发方式。 ArkTS引入了渲染引擎的增强&#xff0c…
阅读更多...
04. 【Android教程】Android 工程解析及使用

04. 【Android教程】Android 工程解析及使用

在上一章中已经搭建好了 Android 开发环境&#xff0c;本章我们将一起通过 Eclipse 创建我们的第一个 Android App。 1. 创建 Android 工程 首先打开 Eclipse&#xff0c;在菜单栏依次选择“New” -> “Android App Project”。如果是第一次创建&#xff0c;可能没有“Andr…
阅读更多...
ChatGPT，来一份3·28雷布斯米时捷上市发布会即时发言稿

ChatGPT，来一份3·28雷布斯米时捷上市发布会即时发言稿

你新招了一个秘书。上班第一天&#xff0c;你对他说&#xff1a;“3月28号我可能会受邀参加雷老板的米时捷’上市发布会&#xff0c;届时我可能会有十分钟的发言机会&#xff0c;你现在准备一篇演讲稿。” 秘书问你有何指导意见&#xff1f; 你自己都不知说啥子&#xff0c;能…
阅读更多...
gcc任意版本安装流程（linux）

gcc任意版本安装流程（linux）

一.更换镜像源 仅仅针对有需要换镜像需求的用户 sudo gedit /etc/apt/sources.list 用于在基于Debian的Linux发行版&#xff08;如Ubuntu&#xff09;上用来编辑软件源列表的命令。 我们更换阿里源&#xff1a; deb http://mirrors.aliyun.com/ubuntu/ focal main restricted…
阅读更多...
fl studio21.2中文版下载及使用基础教学

fl studio21.2中文版下载及使用基础教学

FL Studio 21.2.2是一款功能强大的音乐制作软件&#xff0c;也被广大用户称为“水果编曲”。这款软件支持简体中文和英语&#xff0c;适用于Windows 10/11&#xff08;仅限64位&#xff09;以及MacOS 10.13.6或更高版本的系统。 在FL Studio 21.2.2中&#xff0c;用户可以享受…
阅读更多...
AI论文速读 | 【综述】用于轨迹数据管理和挖掘的深度学习：综述与展望

AI论文速读 | 【综述】用于轨迹数据管理和挖掘的深度学习：综述与展望

论文标题&#xff1a;Deep Learning for Trajectory Data Management and Mining: A Survey and Beyond 作者&#xff1a;Wei Chen(陈伟), Yuxuan Liang(梁宇轩), Yuanshao Zhu, Yanchuan Chang, Kang Luo, Haomin Wen(温皓珉), Lei Li, Yanwei Yu(于彦伟), Qingsong Wen(文青…
阅读更多...
【PADS 原理图Logic发送网表元器件丢失的解决办法】

【PADS 原理图Logic发送网表元器件丢失的解决办法】

1、PADS版本&#xff1a;VX1.2 2、PADS Logic原理图导入PCB Layout后&#xff0c;发现总有几个元器件怎么导都不会显示在PADS Layout上&#xff0c;如下图&#xff1a; PADS Logic上也选择了封装&#xff0c;还是不行&#xff0c;如下图&#xff1a; 3、解决办法&#xff1a; …
阅读更多...
深入了解 Postman 请求头的使用方法

深入了解 Postman 请求头的使用方法

当你在使用 Postman 发送请求时&#xff0c;请求头&#xff08;Headers&#xff09;是你可以包含在 HTTP 请求中的重要部分之一。请求头包含了关于请求的元数据信息&#xff0c;这些信息对于服务器来处理请求是非常重要的。下面是一份详细的图文介绍&#xff0c;说明了如何在 P…
阅读更多...
电源模块 YULIN俞霖科技DC/DC电源模块 直流升压 高压稳压

电源模块 YULIN俞霖科技DC/DC电源模块 直流升压 高压稳压

Features 最低工作电压&#xff1a;0.7V电压隔离&#xff1a;1000VDC /3000VDC 平均无故障时间&#xff1a; > 800,000 小时短路与电弧保护无最低负载要求&#xff1a;可空载工作输入电压&#xff1a;5、12、15、24VDCOutput 100,200、300、400、500 、600、800、 1000、1…
阅读更多...
特征工程 | 特征选择、特征降维

特征工程 | 特征选择、特征降维

目录 一. 特征选择1. 方差选择法2. 相关系数法3. 卡方检验 二. 特征降维1. LDA(线性判别分析法)2. PCA(主成分析法) 一. 特征选择 特征选择的目的是从原有特征中找出主要特征&#xff0c;原始特征可能包含冗余或无关变量&#xff08;或称特征、属性、指标等&#xff09; 手工 …
阅读更多...
门店稽查的主要涵盖范围

门店稽查的主要涵盖范围

先有需求再有目标&#xff0c;门店稽查也是如此&#xff0c;当品牌有线下终端的查价、上架率、竞品调研等的需求&#xff0c;则需要安排神秘访员进行上门稽查&#xff0c;整个过程可以分为明访和暗访&#xff0c;稽查方式的不同&#xff0c;对于稽查的结果会有差异&#xff0c;…
阅读更多...
[深度学习]yolov8+pyqt5搭建精美界面GUI设计源码实现五

[深度学习]yolov8+pyqt5搭建精美界面GUI设计源码实现五

【简单介绍】 依托先进的目标检测算法YOLOv8与灵活的PyQt5界面开发框架&#xff0c;我们倾力打造出了一款集直观、易用与功能强大于一体的目标检测GUI界面软件。通过深度融合YOLOv8在目标识别领域的出色性能与PyQt5的精美界面设计&#xff0c;我们成功推出了一款高效且稳定的软…
阅读更多...
电脑开机0x0000007B蓝屏怎么办?

电脑开机0x0000007B蓝屏怎么办?

电脑开机0x0000007B蓝屏怎么办啊?相信很多用户的电脑都有遇到过蓝屏的问题，最近有用户电脑一开机就蓝屏，并且显示0x0000007B错误代码，原本想通过安全模式进行修复，结果发现安全模式进不去，不知道该怎么解决。这可能与我们的内存或硬盘有关，尝试设置一下硬盘模式，看看是…
阅读更多...
R语言随机抽取数据，并作两组数据间t检验，并保存抽取的数据，并绘制boxplot

R语言随机抽取数据，并作两组数据间t检验，并保存抽取的数据，并绘制boxplot

前提&#xff1a;接着上述R脚本输出的seed结果来选择应该使用哪个seed比较合理&#xff0c;上个R脚本名字&#xff1a; “5utr_计算ABD中Ge1和Lt1的个数和均值以及按照TE个数小的进行随机100次抽样.R” 1.输入数据&#xff1a;“5utr-5d做ABD中有RG4和没有RG4的TE之间的T检验.c…
阅读更多...
基于51单片机的智能晾衣架设计资料(论文+源码+仿真)

基于51单片机的智能晾衣架设计资料(论文+源码+仿真)

目录 1、资料内容 2、整体架构流程 3、主控单元设计 4、LCD液晶显示 5、仿真图 6、程序 资料下载地址&#xff1a;基于51单片机的智能晾衣架设计资料(论文源码仿真) 1、资料内容 2、整体架构流程 为了实现晾衣自身能够完成对外界数据的采集与分析&#xff0c;集成控制环节我们采…
阅读更多...
【多模态融合】SuperFusion 激光雷达与相机多层次融合 远距离高清地图预测 ICRA 2024

【多模态融合】SuperFusion 激光雷达与相机多层次融合 远距离高清地图预测 ICRA 2024

前言 本文介绍激光雷达与相机进行多层次融合&#xff0c;包括数据级融合、特征级融合和BEV级融合。 融合后的BEV特征可以支持不同的任务头&#xff0c;包括语义分割、实例编码和方向预测&#xff0c;最后进行后处理生成高清地图预测&#xff0c;它是来自ICRA 2024的。 会讲解…
阅读更多...
集合系列(十五) -CopyOnWriteArrayList详解

集合系列(十五) -CopyOnWriteArrayList详解

一、摘要 在介绍 CopyOnWriteArrayList 之前&#xff0c;我们一起先来看看如下方法执行结果&#xff0c;代码内容如下&#xff1a; public static void main(String[] args) {List<String> list new ArrayList<String>();list.add("1");list.add(&quo…
阅读更多...
[BT]BUUCTF刷题第8天（3.26）

[BT]BUUCTF刷题第8天（3.26）

第8天 Web [CISCN2019 华北赛区 Day2 Web1]Hack World 题目明确提示flag在flag表里的flag列&#xff0c;这里先尝试1 返回&#xff1a;你好&#xff0c;glzjin想要一个女朋友。 再尝试1&#xff0c;返回bool(false) 到这里就感觉是布尔盲注的题目类型了&#xff08;虽然我没…
阅读更多...
推荐文章
最新文章

Copyright @ 2022~2023