Cisco Catalyst3850交换机RTU license使用方法

1 情况说明

客户处采购了4台3850-14T交换机,在配置的时候发现OSPF不支持,
查询原因为当前license不支持 (lanbase, 只能支持2层功能)
报错如下:

Access-3850-1(config)#router ospf 100
Protocol not in this image

2 如何处理?

开启RTU license,加载ip service类型的license
开启RTU License后正常。如下图:

Access-3850-1(config)#router ospf 100
Access-3850-1(config-router)#

3 扫盲: 啥是RTU license What is RTU License ?

A Right to Use license scheme is an honor-based model for licensing. Licenses are not tied to an unique device identifier (UDI), product ID, or serial number.
看到上面所说的了吗? honor-based model ,说人话就是你应该购买license,但你可以直接使用。不买就用的就是臭不要脸。

我的理解,实际上就是cisco为了简化license安装和加载,以前的交换机或路由器上要加载license需要几步:

  1. 购买了license后,登录cisco.com官网
  2. 输入license信封上的key,并输入交换机的SN进行绑定,—>生成license文件—>下载下来
  3. 通过install license命令进行安装

现在不需要这么繁琐了,可以直接加载使用。

4 具体操作方法

4.1 无法运行OSPF, 报错

Access-3850-1(config)#router ospf 100
Protocol not in this image

4.2 查看license

Access-3850-1#show license right-to-use usage Slot#  License Name     Type     usage-duration(y:m:d)  In-Use  EULA
-----------------------------------------------------------------------1      ipservices     permanent    0 :0 :0                no    no   1      ipservices     evaluation   0 :0 :0                no    no   1      ipbase         permanent    0 :0 :0                no    no   1      ipbase         evaluation   0 :0 :0                no    no   1      lanbase        permanent    0 :0 :0                yes   yes  //这就是当前的license 类型1      apcount        evaluation   0 :0 :0                no    no   1      apcount        base         0 :0 :0                no    no   1      apcount        adder        0 :0 :0                no    no

4.3 启用ipservices license

3850-1#license right-to-use activate ipservices all  acceptEULA 
% switch-1:stack-mgr:Reboot the switch to invoke the highest activated License level

4.4 Reload 重启交换机

3850-1#reload 
Reload command is being issued on Active unit, this will reload the whole stack
Proceed with reload? [confirm]

3.5 重启完成,查看license

3850-1#show license right-to-use usage Slot#  License Name     Type     usage-duration(y:m:d)  In-Use  EULA1      ipservices     permanent    0 :0 :0                yes   yes    //加载了ip service1      ipservices     evaluation   0 :0 :0                no    no   1      ipbase         permanent    0 :0 :0                no    no   1      ipbase         evaluation   0 :0 :0                no    no   1      lanbase        permanent    0 :0 :0                no    yes  1      apcount        evaluation   0 :0 :0                no    no   1      apcount        base         0 :0 :0                no    no   1      apcount        adder        0 :0 :0                no    no   

3.6 再次启用ospf进程

3850-1(config)#router os 100
IP routing not enabled报了个错,但这个和license无关,是因为没有开ip routing***开启ip routing***3850-1(config)#ip routing
3850-1(config)#router ospf 100
3850-1(config-router)#router ospf 100

其他查看命令


3850-1#license right-to-use activate ?apcount     configure the AP-count licenses on the switchipbase      activate ipbase license on the switchipservices  activate Ipservices license on the switchlanbase     activate lanbase license on the switch3850-1#license right-to-use activate ipservices all  acceptEULA 
% switch-1:stack-mgr:Reboot the switch to invoke the highest activated License level3850-1#show license right-to-use usage Slot#  License Name     Type     usage-duration(y:m:d)  In-Use  EULA
-----------------------------------------------------------------------1      ipservices     permanent    0 :0 :0                no    yes  1      ipservices     evaluation   0 :0 :0                no    no   1      ipbase         permanent    0 :0 :0                no    no   1      ipbase         evaluation   0 :0 :0                no    no   1      lanbase        permanent    0 :0 :0                yes   yes  1      apcount        evaluation   0 :0 :0                no    no   1      apcount        base         0 :0 :0                no    no   1      apcount        adder        0 :0 :0                no    no  不加eula参数,需要确认agreement.3850-1#license right-to-use activate ipservices all 
PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR LICENSE KEY PROVIDED FOR ANY CISCO PRODUCT FEATURE OR USING SUCH PRODUCT FEATURE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN. Use of this product feature requires an additional license from Cisco, together with an additional payment.  You may use this product feature subject to the Cisco end user license agreement http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html, together with any supplements relating to such product feature.   It is your responsibility to make payment to Cisco for your use of the product feature if not already licensed to do so. Your acceptance of this agreement for the software features on one product shall be deemed your acceptance with respect to all such software on all Cisco products you purchase which includes the same software.  (The foregoing notwithstanding, you must purchase a license for each software feature you use, so that if you enable a software feature on 1000 devices, you must purchase 1000 licenses for use.)    This license may be transferrable from another Cisco device of the same model for the same functionality if such license already is owned.  Activation of the software command line interface will be evidence of your acceptance of this agreement. By clicking  the "accept" button  or typing "yes" you are  indicating  you have read and agree to be bound by all the terms provided herein.ACCEPT (yes/no) : yes
% switch-1:stack-mgr:Reboot the switch to invoke the highest activated License level3850-1#reload System configuration has been modified. Save? [yes/no]: y
Building configuration...
Compressed configuration from 3001 bytes to 1475 bytes[OK]Reload command is being issued on Active unit, this will reload the whole stack
Proceed with reload? [confirm]3850-1#show license right-to-use  default Slot#    License Name    Type      Count 
------------------------------------------1        lanbase        permanent     N/A 1        apcount        base          0   3850-1#show license right-to-use  de      
3850-1#show license right-to-use  deta
3850-1#show license right-to-use  detail 
Index 1:  License Name: ipservicesPeriod left: LifetimeLicense Type: permanentLicense State: Active, In useLicense Count: Non-CountedLicense Location: Slot 1
Index 2:  License Name: ipservicesPeriod left: 90License Type: evaluationLicense State: Not ActivatedLicense Count: Non-CountedLicense Location: Slot 1
Index 3:  License Name: ipbasePeriod left: LifetimeLicense Type: permanentLicense State: Not ActivatedLicense Count: Non-CountedLicense Location: Slot 1
Index 4:  License Name: ipbasePeriod left: 90License Type: evaluationLicense State: Not ActivatedLicense Count: Non-CountedLicense Location: Slot 1
Index 5:  License Name: lanbasePeriod left: LifetimeLicense Type: permanentLicense State: Active, Not In useLicense Count: Non-CountedLicense Location: Slot 1
Index 6:  License Name: apcountPeriod left: 90License Type: evaluationLicense State: Not ActivatedLicense Count: 50License Location: Slot 1
Index 7:  License Name: apcountPeriod left: LifetimeLicense Type: baseLicense State: Not ActivatedLicense Count: 0License Location: Slot 1
Index 8:  License Name: apcountPeriod left: LifetimeLicense Type: adderLicense State: Not ActivatedLicense Count: 0License Location: Slot 13850-1#show license right-to-use  summary License Name    Type     Count   Period left
-----------------------------------------------ipservices   permanent   N/A      Lifetimeapcount      base        0        Lifetimeapcount      adder       0        Lifetime--------------------------------------------License Level In Use: ipservices
License Level on Reboot: ipservices
Evaluation AP-Count: Disabled
Total AP Count Licenses: 0
AP Count Licenses In-use: 0
AP Count Licenses Remaining: 0

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处:http://www.mzph.cn/news/766469.shtml

如若内容造成侵权/违法违规/事实不符,请联系多彩编程网进行投诉反馈email:809451989@qq.com,一经查实,立即删除!

相关文章

JMeter并发工具的使用

视频地址:Jmeter安装教程01_Jmeter之安装以及环境变量配置_哔哩哔哩_bilibili 一、JMeter是什么 JMeter是一款免安装包,官网下载好后直接解压缩并配置好环境变量就可以使用。 环境变量配置可参考:https://www.cnblogs.com/liulinghua90/p/…

【Docker】golang操作容器使用rename动态更新容器的名字

【Docker】golang操作容器使用rename动态更新容器的名字 大家好 我是寸铁👊 总结了一篇golang操作容器使用rename动态更新容器的名字✨ 喜欢的小伙伴可以点点关注 💝 前言 今天遇到一个新的需求,要动态改变运行中的容器名字。 可以考虑先把…

实际上,人机协同包括四种情况

人机协同并不是指机器完全取代人类,而是指人与机器之间相互配合、互补的关系。在人机协同中,机器的优势在于高速计算、大数据处理和精确性等方面,而人类则具有创造性思维、灵活性和情感等优势。因此,人机协同的真正价值在于充分发…

使用 Python 快速开始机器学习

🔗 快速开始 PyTorch|使用 Python 建立深度学习模型 认识 PyTorch 1.1 Torch 与 PyTorch 1.2 安装 PyTorch 1.3 验证安装并查看 PyTorch 版本PyTorch 深度学习模型的建立范式 2.1 准备数据 2.2 定义模型 2.3 训练模型 2.4 评估模型 2.5 做出预测为预测任…

vivo (iQOO)安卓14oriainOS4文件管理问题(iQOO8Pro实操)

昨天系统升到烂橘子4后发现文件管理权限又一步收紧了。今天折腾了一下又可以用了,分享一下我的方法。 在应用商店中找到雪豹速清 下载雪豹速清后点击工具箱上面的设置 找到shizuku 点击下载 下载完成后安装进入shizuku 然后我们选择使用通过无线调试启动 开启链…

音频变压器电感的工艺结构原理及选型参数总结

🏡《总目录》 目录 1,概述2,工作原理2.1,材料特性2.2,温度升高2.3,温度降低2.4,数学模型3,结构特点3.1,磁芯3.2,线圈3.3,骨架3.4,绝缘材料4,工艺流程4.1,材料准

阿里云部署OneApi

基于 Docker 进行部署 # 使用 SQLite 的部署命令: docker run --name one-api -d --restart always -p 3000:3000 -e TZAsia/Shanghai -v /home/ubuntu/data/one-api:/data justsong/one-api # 使用 MySQL 的部署命令,在上面的基础上添加 -e SQL_DSN&qu…

java 事件驱动模型(事件发布和监听@EventListener)

一、需要了解的概念 1、Aware机制: Spring 容器在创建 bean 的过程中,会检查 bean 是否实现了某些特定的 Aware 接口,如果实现了,则会在合适的时机调用相应的 setter 方法,将相关的对象注入到 bean 中。 2、Applicati…

独立服务器和云计算各有什么优势?

独立服务器和云计算都是在不同场景下应用广泛的计算解决方案。德迅云安全和您来探讨独立服务器和云计算的优势,并对比它们在性能、灵活性、可扩展性、成本效益和安全性等方面的差异,帮助读者更好地理解并选择适合自己需求的解决方案。 独立服务器和云计算…

jmeter之接口功能自动化

一、接口测试简述 接口:用来连接前端,后端还有移动端的程序模块。由于不同端的工作进度不一样,需要对最开始出来的接口进行接口测试。 接口分类:POST,GET,PUT,DELETE。 POST请求的数据是放在…

Linux系统下C++程序运行时的内存布局详解。【C++】

Linux系统下C程序的虚拟内存模型。 1.程序代码段存储内容生命周期初始化时机特点代码演示 2.只读初始化数据段存储内容生命周期初始化时机特点代码演示 3.读写初始化数据段存储内容生命周期初始化时机特点代码演示 4. 堆区(Heap)存储内容生命周期初始化时…

相交链表:寻找链表的公共节点

目录 一、公共节点 二、题目 三、思路 四、代码 五、代码解析 1.计算长度 2.等长处理 3.判断 六、注意点 1.leetcode的尿性 2.仔细观察样例 3.经验总结 一、公共节点 链表不会像两直线相交一样,相交之后再分开。 由于单链表只有一个next指针&#xff0…

Linux:Jenkins全自动持续集成持续部署(3)

在上一章部署好了之后,还需要点击一下才能进行部署,本章的效果是:当gitlab上的代码发生了变化后,我们不需要做任何事情不需要去点击构建按钮,Jenkins直接自动检测变化,然后自动去集成部署Linux:…

Dr4g0n

信息收集 # nmap -sn 192.168.56.0/24 -oN live.nmap Starting Nmap 7.94 ( https://nmap.org ) at 2024-03-04 08:52 CST Nmap scan report for 192.168.56.2 Host is up (0.00012s latency). MAC Address: 00:50:56:FE:B1:6F (VMware) Nmap scan report …

MATLAB下载+安装教程

下载 MATLAB: 访问 MathWorks 官方网站:MathWorks 官方网站在网站上找到 "Downloads"(下载)选项,并选择 MATLAB。登录或创建一个 MathWorks 帐号。选择您希望下载的 MATLAB 版本,并根据您的操作…

二进制源码部署mysql8.0.35

二进制部署mysql8.0.35 创建mysql用户 [rootzyq ~]#: useradd -r -s /sbin/nologin -M mysql [rootzyq ~]#: id mysql uid990(mysql) gid990(mysql) groups990(mysql)上传mysql文件 [rootzyq ~]#: ls anaconda-ks.cfg mysql-8.0.35-linux-glibc2.28-x86_64.tar.xz解压 [roo…

Uniapp manifest

manifest.json 应用配置 manifest.json 文件是应用的配置文件,用于指定应用的名称、图标、权限等。HBuilderX 创建的工程此文件在根目录,CLI 创建的工程此文件在 src 目录。 #配置项列表 属性类型默认值描述最低版本nameString应用名称appidString新建…

飞鸟写作靠谱吗 #知识分享#媒体

飞鸟写作是一个被广泛使用的论文写作工具,它不仅可以帮助用户快速完成论文写作,还可以进行查重和降重,确保论文的原创性。那么,飞鸟写作到底靠不靠谱呢?在我看来,飞鸟写作绝对是一个靠谱的工具。 首先&…

hadoop基本概念

一、概念 Hadoop 是一个开源的分布式计算和存储框架。 Hadoop 使用 Java 开发,所以可以在多种不同硬件平台的计算机上部署和使用。其核心部件包括分布式文件系统 (Hadoop DFS,HDFS) 和 MapReduce。 二、HDFS 命名节点 (NameNode) 命名节点 (NameNod…

【ai技术】(4):在树莓派上,使用qwen0.5b大模型+chatgptweb,搭建本地大模型聊天环境,速度飞快,非常不错!

1,视频地址 https://www.bilibili.com/video/BV1VK421i7CZ/ 2,下载镜像 raspberry-pi-os-64-bit https://blog.csdn.net/freewebsys/article/details/136921703 项目地址: https://www.raspberrypi.com/software/operating-systems/#rasp…