---

前言

本文分享一个自己编写的电动蝶阀控制逻辑块。

---

一、功能概述

1. 手动状态、自动状态、机旁状态、强制状态、检修状态自由切换；
2. 具有开阀超时、关阀超时报警功能；
3. 手动状态下，按开阀按钮开阀，按关阀按钮关阀；
4. 自动状态下，根据程序联锁要求自动开阀关阀；
5. 强制状态下，跳过允许开阀关阀条件，直接开阀或关阀；
6. 检修状态下，自动关阀，且按下开阀按钮不允许开阀；
7. 按停阀按钮，按钮停止开阀或关阀。

二、电动蝶阀程序编写

1.创建自定义数据类型

2.创建FB功能块“电动蝶阀”

建立如下引脚变量：

3.编写程序

代码如下：
1.赋值

#HMI.Ready_DI := #Ready_DI;
#HMI.Locally_DI := #Locally_DI;
#HMI.Open_DI := #Open_DI;
#HMI.Close_DI := #Close_DI;
#Open_DO := #HMI.Open_DO;
#Close_DO := #HMI.Close_DO;
#Open_Ovq_DO := #HMI.Open_Ovq_DO;
#Close_Ovq_DO := #HMI.Close_Ovq_DO;

2.时间转换、启动超时判断、故障复位

#HMI.#Fault_ALL := #Fault OR #HMI.#Open_Time_Out OR #HMI.#Close_Time_Out OR #HMI.#Limit_Fault OR #Open_Ovq_DI OR #Close_Ovq_DI; //故障赋值
#HMI.#Lcl_DO := #Locally_DI AND #HMI.#HMI_Lcl; //有就地信号，且按下机旁允许按钮，才会显示机旁允许状态#Open_Time := DINT_TO_TIME(REAL_TO_DINT(#HMI.#Open_T_Set * 1000.0)); //输入1表示1S
#Close_Time := DINT_TO_TIME(REAL_TO_DINT(#HMI.#Close_T_Set * 1000.0));#Open_IEC(IN := #Open_DO AND NOT #HMI.#HMI_Close AND NOT #Open_DI AND NOT #HMI.#Limit_Fault,PT := #Open_Time); //开阀延时
#Close_IEC(IN := #Close_DO AND NOT #HMI.#HMI_Open AND NOT #Close_DI AND NOT #HMI.#Limit_Fault,PT := #Close_Time); //关阀延时
#Limit_IEC(IN := #Open_DI AND #Close_DI,PT := #Limit_Time); //限位超时IF #Open_IEC.Q THEN#HMI.#Open_Time_Out := 1;#HMI.#Open_DO := 0;
END_IF; //开阀超时输出
IF #Close_IEC.Q THEN#HMI.#Close_Time_Out := 1;#HMI.#Close_DO := 0;
END_IF; //关阀超时输出
IF #Limit_IEC.Q THEN#HMI.#Limit_Fault := 1;#HMI.#Open_DO := 0;#HMI.#Close_DO := 0;
END_IF; //限位故障输出IF #HMI.#HMI_Rst THEN#HMI.#Fault_ALL := 0;#HMI.#Limit_Fault := 0; //复位限位故障输出#HMI.#Open_Time_Out := 0; //复位开阀超时输出#HMI.#Close_Time_Out := 0; //复位关阀超时输出
END_IF;#HMI.#Open_Ovq_DO := #Open_Ovq_DI;
#HMI.#Close_Ovq_DO := #Close_Ovq_DI;

3.检测信号上升沿

#P_HMI_Lcl(CLK := #HMI.#HMI_Lcl);
#P_HMI_EmgManual(CLK := #HMI.#HMI_EmgManual);
#P_HMI_Pause(CLK := #HMI.#HMI_Pause);

4.手动状态显示

IF #HMI.#HMI_Manual = 1 AND NOT #HMI.#HMI_Auto AND NOT #HMI.#HMI_EmgManual AND NOT #HMI.#HMI_Pause AND NOT #HMI.#Lcl_DO THEN#HMI.#Manual_DO := 1;#HMI.#Auto_DO := 0;#HMI.#EmgManual_DO := 0;
END_IF;
//默认手动状态
IF NOT #HMI.#Auto_DO AND NOT #HMI.#Pause_DO AND NOT #HMI.#Lcl_DO AND NOT #HMI.#EmgManual_DO THEN#HMI.#Manual_DO := 1;#HMI.#Auto_DO := 0;#HMI.#EmgManual_DO := 0;
END_IF;

5.自动状态显示

IF #HMI.#HMI_Auto = 1 AND NOT #HMI.#HMI_Manual AND NOT #HMI.#HMI_EmgManual AND NOT #HMI.#HMI_Pause AND NOT #HMI.#Lcl_DO THEN#HMI.#Manual_DO := 0;#HMI.#Auto_DO := 1;#HMI.#EmgManual_DO := 0;
END_IF;

6.强制状态显示

IF #HMI.#HMI_EmgManual = 1 AND NOT #HMI.#HMI_Manual AND NOT #HMI.#HMI_Auto AND NOT #HMI.#HMI_Pause AND NOT #HMI.#Lcl_DO THEN#HMI.#Manual_DO := 0;#HMI.#Auto_DO := 0;#HMI.#EmgManual_DO := 1;#HMI.#HMI_Pause := 0;
END_IF;
IF #HMI.#HMI_EmgManual = 0 THEN#HMI.#EmgManual_DO := 0;
END_IF;

7.休止状态显示

IF #HMI.#HMI_Pause = 1 AND NOT #HMI.#HMI_Manual AND NOT #HMI.#HMI_Auto AND NOT #HMI.#HMI_EmgManual AND NOT #HMI.#Lcl_DO THEN#HMI.#Manual_DO := 0;#HMI.#Auto_DO := 0;#HMI.#EmgManual_DO := 0;#HMI.#Pause_DO := 1;#HMI.#HMI_EmgManual := 0;
END_IF;
IF #HMI.#HMI_Pause = 0 THEN#HMI.#Pause_DO := 0;
END_IF;

8.手动状态下开阀、关阀

IF #Ready_DI AND #HMI.#HMI_Open AND #HMI.#Manual_DO AND NOT #HMI.#HMI_Close AND NOT #HMI.#Limit_Fault AND NOT #HMI.#Open_Time_Out AND NOT #HMI.#Pause_DO AND NOT #HMI.#Lcl_DO AND NOT #Open_Ovq_DI AND NOT #Fault THEN#HMI.#Open_DO := 1;#HMI.#Close_DO := 0;
END_IF;
IF #Ready_DI AND #HMI.#HMI_Close AND #HMI.#Manual_DO AND NOT #HMI.#HMI_Open AND NOT #HMI.#Limit_Fault AND NOT #HMI.#Close_Time_Out AND NOT #HMI.#Pause_DO AND NOT #HMI.#Lcl_DO AND NOT #Close_Ovq_DI AND NOT #Fault THEN#HMI.#Open_DO := 0;#HMI.#Close_DO := 1;
END_IF;

9.自动状态下开阀、关阀

IF #Ready_DI AND #Auto_Open AND #HMI.#Auto_DO AND NOT #HMI.#HMI_Close AND NOT #HMI.#Limit_Fault AND NOT #HMI.#Open_Time_Out AND NOT #HMI.#Pause_DO AND NOT #HMI.#Lcl_DO AND NOT #Open_Ovq_DI AND NOT #Fault THEN#HMI.#Open_DO := 1;#HMI.#Close_DO := 0;
END_IF;
IF #Ready_DI AND #Auto_Close AND #HMI.#Auto_DO AND NOT #HMI.#HMI_Open AND NOT #HMI.#Limit_Fault AND NOT #HMI.#Close_Time_Out AND NOT #HMI.#Pause_DO AND NOT #HMI.#Lcl_DO AND NOT #Close_Ovq_DI AND NOT #Fault THEN#HMI.#Open_DO := 0;#HMI.#Close_DO := 1;
END_IF;

10.强制状态下开阀、关阀

IF #HMI.#EmgManual_DO AND #HMI.#HMI_Open AND NOT #HMI.#Pause_DO AND NOT #HMI.#Lcl_DO AND NOT #Open_Ovq_DI AND NOT #Fault AND NOT #HMI.#Limit_Fault AND NOT #HMI.#Open_Time_Out THEN#HMI.#Open_DO := 1;#HMI.#Close_DO := 0;
END_IF;
IF #HMI.#EmgManual_DO AND #HMI.#HMI_Close AND NOT #HMI.#Pause_DO AND NOT #HMI.#Lcl_DO AND NOT #Close_Ovq_DI AND NOT #Fault AND NOT #HMI.#Limit_Fault AND NOT #HMI.#Close_Time_Out THEN#HMI.#Open_DO := 0;#HMI.#Close_DO := 1;
END_IF;

11.停阀

IF (#HMI.#Manual_DO OR #HMI.#Auto_DO OR #HMI.#EmgManual_DO) AND #HMI.#HMI_Stop THEN#HMI.#Open_DO := 0;#HMI.#Close_DO := 0;
END_IF;

12.休止状态下关阀

IF #HMI.#Pause_DO AND NOT #HMI.#HMI_Lcl AND NOT #HMI.#Lcl_DO THEN#HMI.#Open_DO := 0;#HMI.#Close_DO := 1;
END_IF;

13.开关到位后，开阀关阀不再输出

IF #Open_DI THEN#HMI.#Open_DO := 0;
END_IF;
IF #Close_DI THEN#HMI.#Close_DO := 0;
END_IF;

14.按钮互锁

IF #HMI.#HMI_Lcl AND #P_HMI_EmgManual.Q THEN#HMI.#HMI_EmgManual := 0;
END_IF;
IF #HMI.#HMI_Lcl AND #P_HMI_Pause.Q THEN#HMI.#HMI_Pause := 0;
END_IF;IF #HMI.#HMI_EmgManual AND #P_HMI_Lcl.Q THEN#HMI.#HMI_Lcl := 0;
END_IF;
IF #HMI.#HMI_EmgManual AND #P_HMI_Pause.Q THEN#HMI.#HMI_Pause := 0;
END_IF;IF #HMI.#HMI_Pause AND #P_HMI_Lcl.Q THEN#HMI.#HMI_Lcl := 0;
END_IF;
IF #HMI.#HMI_Pause AND #P_HMI_EmgManual.Q THEN#HMI.#HMI_EmgManual := 0;
END_IF;

15.按钮自复位

IF NOT "AlwaysFALSE" THEN#HMI.#HMI_Open := 0;#HMI.#HMI_Close := 0;#HMI.#HMI_Manual := 0;#HMI.#HMI_Auto := 0;#HMI.#HMI_Rst := 0;#HMI.#HMI_Stop := 0;
END_IF;