STM32-OLED显示屏

*本文采用的OLED显示屏为4针脚IIC显示屏，4针脚分别为GND，VCC，SCL，SDA

OLED.C

#include "stm32f10x.h"
#include "OLED_Font.h"/*引脚配置*/
#define OLED_W_SCL(x)		GPIO_WriteBit(GPIOB, GPIO_Pin_8, (BitAction)(x))
#define OLED_W_SDA(x)		GPIO_WriteBit(GPIOB, GPIO_Pin_9, (BitAction)(x))/*引脚初始化*/
void OLED_I2C_Init(void)
{RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);GPIO_InitTypeDef GPIO_InitStructure;GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD;GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8;GPIO_Init(GPIOB, &GPIO_InitStructure);GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;GPIO_Init(GPIOB, &GPIO_InitStructure);OLED_W_SCL(1);OLED_W_SDA(1);
}/*** @brief  I2C开始* @param  无* @retval 无*/
void OLED_I2C_Start(void)
{OLED_W_SDA(1);OLED_W_SCL(1);OLED_W_SDA(0);OLED_W_SCL(0);
}/*** @brief  I2C停止* @param  无* @retval 无*/
void OLED_I2C_Stop(void)
{OLED_W_SDA(0);OLED_W_SCL(1);OLED_W_SDA(1);
}/*** @brief  I2C发送一个字节* @param  Byte 要发送的一个字节* @retval 无*/
void OLED_I2C_SendByte(uint8_t Byte)
{uint8_t i;for (i = 0; i < 8; i++){OLED_W_SDA(Byte & (0x80 >> i));OLED_W_SCL(1);OLED_W_SCL(0);}OLED_W_SCL(1);	//额外的一个时钟，不处理应答信号OLED_W_SCL(0);
}/*** @brief  OLED写命令* @param  Command 要写入的命令* @retval 无*/
void OLED_WriteCommand(uint8_t Command)
{OLED_I2C_Start();OLED_I2C_SendByte(0x78);		//从机地址OLED_I2C_SendByte(0x00);		//写命令OLED_I2C_SendByte(Command); OLED_I2C_Stop();
}/*** @brief  OLED写数据* @param  Data 要写入的数据* @retval 无*/
void OLED_WriteData(uint8_t Data)
{OLED_I2C_Start();OLED_I2C_SendByte(0x78);		//从机地址OLED_I2C_SendByte(0x40);		//写数据OLED_I2C_SendByte(Data);OLED_I2C_Stop();
}/*** @brief  OLED设置光标位置* @param  Y 以左上角为原点，向下方向的坐标，范围：0~7* @param  X 以左上角为原点，向右方向的坐标，范围：0~127* @retval 无*/
void OLED_SetCursor(uint8_t Y, uint8_t X)
{OLED_WriteCommand(0xB0 | Y);					//设置Y位置OLED_WriteCommand(0x10 | ((X & 0xF0) >> 4));	//设置X位置高4位OLED_WriteCommand(0x00 | (X & 0x0F));			//设置X位置低4位
}/*** @brief  OLED清屏* @param  无* @retval 无*/
void OLED_Clear(void)
{  uint8_t i, j;for (j = 0; j < 8; j++){OLED_SetCursor(j, 0);for(i = 0; i < 128; i++){OLED_WriteData(0x00);}}
}/*** @brief  OLED显示一个字符* @param  Line 行位置，范围：1~4* @param  Column 列位置，范围：1~16* @param  Char 要显示的一个字符，范围：ASCII可见字符* @retval 无*/
void OLED_ShowChar(uint8_t Line, uint8_t Column, char Char)
{      	uint8_t i;OLED_SetCursor((Line - 1) * 2, (Column - 1) * 8);		//设置光标位置在上半部分for (i = 0; i < 8; i++){OLED_WriteData(OLED_F8x16[Char - ' '][i]);			//显示上半部分内容}OLED_SetCursor((Line - 1) * 2 + 1, (Column - 1) * 8);	//设置光标位置在下半部分for (i = 0; i < 8; i++){OLED_WriteData(OLED_F8x16[Char - ' '][i + 8]);		//显示下半部分内容}
}/*** @brief  OLED显示字符串* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  String 要显示的字符串，范围：ASCII可见字符* @retval 无*/
void OLED_ShowString(uint8_t Line, uint8_t Column, char *String)
{uint8_t i;for (i = 0; String[i] != '\0'; i++){OLED_ShowChar(Line, Column + i, String[i]);}
}/*** @brief  OLED次方函数* @retval 返回值等于X的Y次方*/
uint32_t OLED_Pow(uint32_t X, uint32_t Y)
{uint32_t Result = 1;while (Y--){Result *= X;}return Result;
}/*** @brief  OLED显示数字（十进制，正数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：0~4294967295* @param  Length 要显示数字的长度，范围：1~10* @retval 无*/
void OLED_ShowNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length)
{uint8_t i;for (i = 0; i < Length; i++)							{OLED_ShowChar(Line, Column + i, Number / OLED_Pow(10, Length - i - 1) % 10 + '0');}
}/*** @brief  OLED显示数字（十进制，带符号数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：-2147483648~2147483647* @param  Length 要显示数字的长度，范围：1~10* @retval 无*/
void OLED_ShowSignedNum(uint8_t Line, uint8_t Column, int32_t Number, uint8_t Length)
{uint8_t i;uint32_t Number1;if (Number >= 0){OLED_ShowChar(Line, Column, '+');Number1 = Number;}else{OLED_ShowChar(Line, Column, '-');Number1 = -Number;}for (i = 0; i < Length; i++)							{OLED_ShowChar(Line, Column + i + 1, Number1 / OLED_Pow(10, Length - i - 1) % 10 + '0');}
}/*** @brief  OLED显示数字（十六进制，正数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：0~0xFFFFFFFF* @param  Length 要显示数字的长度，范围：1~8* @retval 无*/
void OLED_ShowHexNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length)
{uint8_t i, SingleNumber;for (i = 0; i < Length; i++)							{SingleNumber = Number / OLED_Pow(16, Length - i - 1) % 16;if (SingleNumber < 10){OLED_ShowChar(Line, Column + i, SingleNumber + '0');}else{OLED_ShowChar(Line, Column + i, SingleNumber - 10 + 'A');}}
}/*** @brief  OLED显示数字（二进制，正数）* @param  Line 起始行位置，范围：1~4* @param  Column 起始列位置，范围：1~16* @param  Number 要显示的数字，范围：0~1111 1111 1111 1111* @param  Length 要显示数字的长度，范围：1~16* @retval 无*/
void OLED_ShowBinNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length)
{uint8_t i;for (i = 0; i < Length; i++)							{OLED_ShowChar(Line, Column + i, Number / OLED_Pow(2, Length - i - 1) % 2 + '0');}
}/*** @brief  OLED初始化* @param  无* @retval 无*/
void OLED_Init(void)
{uint32_t i, j;for (i = 0; i < 1000; i++)			//上电延时{for (j = 0; j < 1000; j++);}OLED_I2C_Init();			//端口初始化OLED_WriteCommand(0xAE);	//关闭显示OLED_WriteCommand(0xD5);	//设置显示时钟分频比/振荡器频率OLED_WriteCommand(0x80);OLED_WriteCommand(0xA8);	//设置多路复用率OLED_WriteCommand(0x3F);OLED_WriteCommand(0xD3);	//设置显示偏移OLED_WriteCommand(0x00);OLED_WriteCommand(0x40);	//设置显示开始行OLED_WriteCommand(0xA1);	//设置左右方向，0xA1正常 0xA0左右反置OLED_WriteCommand(0xC8);	//设置上下方向，0xC8正常 0xC0上下反置OLED_WriteCommand(0xDA);	//设置COM引脚硬件配置OLED_WriteCommand(0x12);OLED_WriteCommand(0x81);	//设置对比度控制OLED_WriteCommand(0xCF);OLED_WriteCommand(0xD9);	//设置预充电周期OLED_WriteCommand(0xF1);OLED_WriteCommand(0xDB);	//设置VCOMH取消选择级别OLED_WriteCommand(0x30);OLED_WriteCommand(0xA4);	//设置整个显示打开/关闭OLED_WriteCommand(0xA6);	//设置正常/倒转显示OLED_WriteCommand(0x8D);	//设置充电泵OLED_WriteCommand(0x14);OLED_WriteCommand(0xAF);	//开启显示OLED_Clear();				//OLED清屏
}

OLED_Font.h

#ifndef __OLED_FONT_H
#define __OLED_FONT_H/*OLED字模库，宽8像素，高16像素*/
const uint8_t OLED_F8x16[][16]=
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//  00x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 10x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 20x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 30x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 40xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 50x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 60x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 70x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 80x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 90x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 100x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 110x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 120x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 130x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 140x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 150x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 160x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 170x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 180x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 190x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 200x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 210x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 220x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 230x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 240x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 250x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 260x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 270x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 280x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 290x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 300x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 310xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 320x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 330x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 340xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 350x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 360x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 370x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 380xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 390x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 400x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 410x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 420x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 430x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 440x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 450x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 460xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 470x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 480xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 490x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 500x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 510x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 520x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 530x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 540xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 550x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 560x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 570x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 580x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 590x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 600x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 610x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 620x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 630x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 640x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 650x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 660x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 670x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 680x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 690x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 700x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 710x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 720x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 730x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 740x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 750x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 760x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 770x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 780x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 790x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 800x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 810x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 820x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 830x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 840x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 850x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 860x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 870x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 880x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 890x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 900x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 910x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 920x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 930x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};#endif

main.c

#include "stm32f10x.h"                  // Device header
#include "Delay.h"
#include "OLED.h"uint8_t KeyNum;int main(void)
{OLED_Init();OLED_ShowChar(1,1,'A');OLED_ShowString(1,3,"Hello World!");OLED_ShowNum(2,1,12345,5);OLED_ShowSignedNum(2,7,-66,2);OLED_ShowHexNum(3,1,0xAA55,4);OLED_ShowBinNum(4,1,0xAA55,16);//OLED_Clear();while (1){}
}

本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若转载，请注明出处：http://www.mzph.cn/news/195633.shtml

如若内容造成侵权/违法违规/事实不符，请联系多彩编程网进行投诉反馈email:809451989@qq.com，一经查实，立即删除！

相关文章

力扣7.整数反转

力扣7.整数反转

题目描述 代码 自己写的像屎山&#xff0c;虽然能通过&#xff0c;但多了很多不必要的代码。 class Solution {public int reverse(int x) {int count 0;int res 0;//用temp2记录x的正负int temp2 x;if(x < 0){x -x;}int temp x;while(temp ! 0){temp temp / 10;cou…
阅读更多...
03 数仓平台 Kafka

03 数仓平台 Kafka

kafka概述 定义 Kafka 是一个开源的分布式事件流平台&#xff08;Event Streaming Plantform&#xff09;&#xff0c;主要用于大数据实时领域。本质上是一个分布式的基于发布/订阅模式的消息队列&#xff08;Message Queue&#xff09;。 消息队列 在大数据场景中主要采用…
阅读更多...
Kubernetes学习笔记-Part.02 Docker版本

Kubernetes学习笔记-Part.02 Docker版本

目录 Part.01 Kubernets与docker Part.02 Docker版本 Part.03 Kubernetes原理 Part.04 资源规划 Part.05 基础环境准备 Part.06 Docker安装 Part.07 Harbor搭建 Part.08 K8s环境安装 Part.09 K8s集群构建 Part.10 容器回退 第二章 Docker版本 老旧版本&#xff1a;docker/doc…
阅读更多...
无人机管控平台：打破通信限制 助力灾害救援

无人机管控平台：打破通信限制 助力灾害救援

中国地域广阔&#xff0c;自然灾害频发&#xff0c;时常对通信基础设施造成破坏&#xff0c;传统无人机在紧急救援中受限。为有效解决这一问题&#xff0c;新一代无人机技术与应急通信系统融合形成无人机管控平台&#xff0c;不仅提供了高效的空中监测技术&#xff0c;还配备先…
阅读更多...
制作一个RISC-V的操作系统三-编译与链接

制作一个RISC-V的操作系统三-编译与链接

文章目录 GCCGCC简介GCC的命令格式gcc -Egcc -cgcc -Sgcc -ggcc -vGCC的主要执行步骤GCC涉及的文件类型针对多个源文件的处理 ELFELF介绍ELF文件格式ELF文件处理相关工具&#xff1a;Binutils&#xff08;binary utility&#xff09;readlelf -hreadelf -S或readelf -SW&#x…
阅读更多...
11月推荐阅读的12篇大语言模型相关论文

11月推荐阅读的12篇大语言模型相关论文

现在已经是12月了&#xff0c;距离2024年只有一个月了&#xff0c;本文总结了11月的一些比较不错的大语言模型相关论文 System 2 Attention (is something you might need too). https://arxiv.org/abs/2311.11829 一种称为S2A的新注意力方法被开发出来&#xff0c;解决llm…
阅读更多...
c语言编程题经典100例——（66~70例）

c语言编程题经典100例——（66~70例）

1,写一个函数&#xff0c;判断一个字符串是否是回文字符串。 下面给出一个用于判断一个字符串是否是回文字符串的demo 函数 #include <stdio.h> #include <string.h> int isPalindrome(char str[]) { int len strlen(str); for (int i 0; i < len / 2;…
阅读更多...
【C语言】字符串函数strlen #strcpy #strcmp #strcat #strstr及其模拟实现

【C语言】字符串函数strlen #strcpy #strcmp #strcat #strstr及其模拟实现

在C语言中&#xff0c;有一种特殊的数据类型&#xff0c;即字符串类型。C 并没有专门定义一个字符串类型&#xff0c;这对我们使用字符串造成了一定的麻烦。但是&#xff0c;C标准库<string.h> 中定义了各种字符串函数&#xff0c;这对于我们来说是一件值得庆幸的事情。…
阅读更多...
PCL 空间直角坐标系与极坐标系的相互转换（C++详细过程版）

PCL 空间直角坐标系与极坐标系的相互转换（C++详细过程版）

目录 一、算法原理1、空间坐标系转极坐标系2、极坐标系转空间坐标系二、代码实现三、结果展示1、空间坐标系转极坐标系2、极坐标系转空间坐标系本文由CSDN点云侠原创，原文链接。爬虫网站自重。如果你不是在点云侠的博客中看到该文章，那么此处便是不
阅读更多...
国内的几款强大的AI智能—AI语言模型

国内的几款强大的AI智能—AI语言模型

R5Ai智能助手是一款由百度研发的文心一言&#xff0c;它支持gpt4 / gpt-3.5 / claude&#xff0c;也支持AI绘画&#xff0c;每天提供十次免费使用机会&#xff0c;无需魔法。该智能助手具有以下优点&#xff1a;会画画&#xff0c;没有使用次数限制&#xff0c;可以在界面上找到…
阅读更多...
动能芯片 | SI3262—高度集成的低功耗SOC芯片 刷卡触摸一体

动能芯片 | SI3262—高度集成的低功耗SOC芯片 刷卡触摸一体

Si3262是一款高度集成的低功耗SOC芯片&#xff0c;其集成了基于RISC-V核的低功耗MCU和工作在13.56MHz的非接触式读写器模块。 MCU模块具有低功耗、Low Pin Count、宽电压工作范围&#xff0c;集成了13/14/15/16位精度的ADC、LVD、UART、SPI、I2C、TIMER、WUP、IWDG、RTC、TSC等…
阅读更多...
JS this指向详解

JS this指向详解

前述 在了解js中this指向之前先简单的阐述一下脚本执行过程和执行上下文的概念 js脚本执行过程 当js引擎执行脚本代码之前会先进行一个预编译阶段&#xff0c;然后创建全局执行上下文入栈&#xff08;上下文调用栈&#xff09;&#xff0c;然后执行全局代码&#xff0c;执行…
阅读更多...
uni-app 微信小程序之自定义navigationBar顶部导航栏

uni-app 微信小程序之自定义navigationBar顶部导航栏

文章目录 1. 实现效果2. App.vue3. pages.json 配置自定义4. 顶部导航栏 使用 微信小程序自定义 navigationBar 顶部导航栏&#xff0c;兼容适配所有机型 1. 实现效果 2. App.vue 在App.vue 中&#xff0c;设置获取的 StatusBar&#xff0c;CustomBar 高度&#xff08;实现适配…
阅读更多...
苍穹外卖--营业额统计

苍穹外卖--营业额统计

营业额统计是基于折现图来展现&#xff0c;并且按照天来展示的。实际上&#xff0c;就是某一个时间范围之内的每一天的营业额。同时&#xff0c;不管光标放在哪个点上&#xff0c;那么它就会把具体的数值展示出来。并且还需要注意日期并不是固定写死的&#xff0c;是由上边时间…
阅读更多...
redis的缓存击穿，缓存穿透，缓存雪崩

redis的缓存击穿，缓存穿透，缓存雪崩

Redis是一个开源的、内存中的数据结构存储系统&#xff0c;它可以用作数据库、缓存和消息代理。Redis支持多种数据结构&#xff0c;如字符串、哈希表、列表、集合和有序集合。此外&#xff0c;Redis还支持各种操作&#xff0c;如读取和写入数据、删除和更新数据等。 Redis的特点…
阅读更多...
【Openstack Train】十五、glance命令合集

【Openstack Train】十五、glance命令合集

本文介绍了glance组件的常用命令。关于openstack的安装&#xff0c;可以参考以下内容&#xff1a; 【Openstack Train安装】一、虚拟机创建 【Openstack Train安装】二、NTP安装 【Openstack Train安装】三、openstack安装 【Openstack Train安装】四、MariaDB/RabbitMQ 安…
阅读更多...
RPC 集群，gRPC 广播和组播

RPC 集群，gRPC 广播和组播

一、集群抽象&#xff1a;cluster 它是指我们在调用远程的时候&#xff0c;尝试解决&#xff1a; 1、failover:即引入重试功能&#xff0c;但是重试的时候会换一个新节点 2、failfast: 立刻失败&#xff0c;不需要重试 3、广播&#xff1a;将请求发送到所有的节点上 4、组…
阅读更多...
一文搞懂系列——动态库的加载方式及应用场景

一文搞懂系列——动态库的加载方式及应用场景

引文 我们在工作中经常会遇到动态库链接的问题&#xff0c;因为正常的方式并不能满足我们的场景。常见的问题可以总结如下&#xff1a; 系统路径默认路径、usr/lib、/lib 目录&#xff0c;不会集成第三方动态库。 同名动态库可能在多个路径中存在。 针对不同的场景&#xff0…
阅读更多...
探索元宇宙链游戏：一场数字世界的奇妙融合

探索元宇宙链游戏：一场数字世界的奇妙融合

随着互联网的飞速发展&#xff0c;以及人们不断对互动娱乐体验的要求提高&#xff0c;元宇宙渐渐成为人们追求的目标。 而区块链技术的出现给元宇宙链游开发带来了新的机遇和挑战。 一、元宇宙链游定义 元宇宙链游全称为基于区块链技术的元宇宙游戏&#xff0c;是一种新型的网…
阅读更多...
ArkTS-列表选择弹窗

ArkTS-列表选择弹窗

调用 每一个sheet中的action对应其点击事件 Button(列表选择弹窗).onClick(() > {ActionSheet.show({title: 列表选择弹窗标题,message: 内容,autoCancel: true,confirm: {value: 确认,action: () > {console.log(Get Alert Dialog handled)}},cancel: () > {console.…
阅读更多...
最新文章

Copyright @ 2022~2023