组网需求
- AC组网方式：旁挂二层组网。
- DHCP部署方式：
- AC作为DHCP服务器为AP分配IP地址。
- 汇聚交换机SwitchB作为DHCP服务器为STA分配IP地址。
- 业务数据转发方式：直接转发。
图1 配置旁挂二层组网直接转发示例组网图
数据规划
| 配置项 | 数据 |
|---|---|
| AP管理VLAN | VLAN100 |
| STA业务VLAN | VLAN101 |
| DHCP服务器 | AC作为DHCP服务器为AP分配IP地址 汇聚交换机SwitchB作为DHCP服务器为STA分配IP地址，STA的默认网关为10.23.101.2 |
| AP的IP地址池 | 10.23.100.2～10.23.100.254/24 |
| STA的IP地址池 | 10.23.101.3～10.23.101.254/24 |
| AC的源接口IP地址 | VLANIF100：10.23.100.1/24 |
| AP组 |
|
| 域管理模板 |
|
| SSID模板 |
|
| 安全模板 |
|
| VAP模板 |
|
配置思路
- 配置AP、AC和周边网络设备之间实现网络互通。
- 配置AP上线。
- 创建AP组，用于将需要进行相同配置的AP都加入到AP组，实现统一配置。
- 配置AC的系统参数，包括国家码、AC与AP之间通信的源接口。
- 配置AP上线的认证方式并离线导入AP，实现AP正常上线。
- 配置WLAN业务参数，实现STA访问WLAN网络功能。
配置注意事项
-
建议在与AP直连的设备接口上配置端口隔离，如果不配置端口隔离，尤其是业务数据转发方式采用直接转发时，可能会在VLAN内形成大量不必要的广播报文，导致网络阻塞，影响用户体验。
-
隧道转发模式下，管理VLAN和业务VLAN不能配置为同一VLAN，且AP和AC之间只能放通管理VLAN，不能放通业务VLAN。
- V200R021C00版本开始，配置CAPWAP源接口或源地址时，会检查和安全相关的配置是否已存在，包括DTLS加密的PSK、AC间DTLS加密的PSK、登录AP的用户名和密码、全局离线管理VAP的登录密码，均已存在才能成功配置，否则会提示用户先完成相关的配置。
- V200R021C00版本开始，AC默认开启CAPWAP控制隧道的DTLS加密功能。开启该功能，添加AP时AP会上线失败，此时需要先开启CAPWAP DTLS不认证方式（capwap dtls no-auth enable）让AP上线，以便AP获取安全凭证，AP上线后应及时关闭该功能（undo capwap dtls no-auth enable），避免未授权AP上线。Web网管的该功能位于“配置 > AC配置 > 基本配置 > AC基本信息 > 高级 > CAPWAP链路配置 > 允许AP以不认证方式与AC进行DTLS会话”。
操作步骤
- 配置周边设备 # 配置接入交换机SwitchA的GE0/0/1和GE0/0/2接口加入VLAN100和VLAN101，GE0/0/1的缺省VLAN为VLAN100。
<span style="color:#333333"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1192280004190921">system-view</strong> [HUAWEI] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1222166240190921">sysname SwitchA</strong> [SwitchA] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1183461715190921">vlan batch 100 101</strong> [SwitchA] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1005154605190921">interface gigabitethernet 0/0/1</strong> [SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1349582656190921">port link-type trunk</strong> [SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b636724399190921">port trunk pvid vlan 100</strong> [SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b103409417190921">port trunk allow-pass vlan 100 101</strong> [SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b896559407190921">port-isolate enable</strong> [SwitchA-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b951942244190921">quit</strong> [SwitchA] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2123180437190921">interface gigabitethernet 0/0/2</strong> [SwitchA-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1745410152190921">port link-type trunk</strong> [SwitchA-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1787123792190921">port trunk allow-pass vlan 100 101</strong> [SwitchA-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1239957325190921">quit</strong></span></span># 配置汇聚交换机SwitchB的接口GE0/0/1加入VLAN100和VLAN101，接口GE0/0/2加入VLAN100，GE0/0/3加入VLAN101。<span style="color:#333333"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1674717277190921">system-view</strong> [HUAWEI] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1445629532190921">sysname SwitchB</strong> [SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b647498740190921">vlan batch 100 101</strong> [SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b125795402190921">interface gigabitethernet 0/0/1</strong> [SwitchB-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b877541276190921">port link-type trunk</strong> [SwitchB-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b707960753190921">port trunk allow-pass vlan 100 101</strong> [SwitchB-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1228466072190921">quit</strong> [SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b298987462190921">interface gigabitethernet 0/0/2</strong> [SwitchB-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b864863078190921">port link-type trunk</strong> [SwitchB-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1730539876190921">port trunk allow-pass vlan 100</strong> [SwitchB-GigabitEthernet0/0/2] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2079017324190921">quit</strong> [SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2040272214190921">interface gigabitethernet 0/0/3</strong> [SwitchB-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b602819935190921">port link-type trunk</strong> [SwitchB-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b916832533190921">port trunk allow-pass vlan 101</strong> [SwitchB-GigabitEthernet0/0/3] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1666471945190921">quit</strong></span></span># 配置Router的接口GE1/0/0加入VLAN101，创建接口VLANIF101并配置IP地址为10.23.101.2/24。<span style="color:#333333"><span style="background-color:#dddddd"><Huawei> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b118005268190921">system-view</strong> [Huawei] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1176501588190921">sysname Router</strong> [Router] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b995805857190921">vlan batch 101</strong> [Router] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b906637926190921">interface gigabitethernet 1/0/0</strong> [Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b406876624190921">port link-type trunk</strong> [Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1226529678190921">port trunk allow-pass vlan 101</strong> [Router-GigabitEthernet1/0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1131638750190921">quit</strong> [Router] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b648829236190921">interface vlanif 101</strong> [Router-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1969966747190921">ip address 10.23.101.2 24</strong> [Router-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1246477905190921">quit</strong></span></span> - 配置AC与其它网络设备互通
如果AC直接连接AP，需要在AC直连AP的接口上配置缺省VLAN为管理VLAN100。
# 配置AC的接口GE0/0/1加入VLAN100。<span style="color:#333333"><span style="background-color:#dddddd"><HUAWEI> <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1248097008190921">system-view</strong> [HUAWEI] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2092838922190921">sysname AC</strong> [AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b2061833437190921">vlan batch 100 101</strong> [AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1024087155190921">interface gigabitethernet 0/0/1</strong> [AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b380448131190921">port link-type trunk</strong> [AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1570869377190921">port trunk allow-pass vlan 100</strong> [AC-GigabitEthernet0/0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b686476124190921">quit</strong></span></span> - 配置DHCP服务器为STA和AP分配IP地址 # 在AC上配置VLANIF100接口为AP提供IP地址。
<span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b270083456190921">dhcp enable</strong> [AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1697431376190921">interface vlanif 100</strong> [AC-Vlanif100] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1645914341190921">ip address 10.23.100.1 24</strong> [AC-Vlanif100] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b2011614048190921">dhcp select interface</strong> [AC-Vlanif100] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1870662344190921">quit</strong></span></span># 在SwitchB上配置VLANIF101接口为STA提供IP地址，并指定10.23.101.2作为STA的默认网关地址。DNS服务器地址请根据实际需要配置。常用配置方法如下：- 接口地址池场景，需要在VLANIF接口视图下执行命令dhcp server dns-list ip-address &<1-8>。
- 全局地址池场景，需要在IP地址池视图下执行命令dns-list ip-address &<1-8>。
<span style="color:#333333"><span style="background-color:#dddddd">[SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1746102230190921">dhcp enable</strong> [SwitchB] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b181711504190921">interface vlanif 101</strong> [SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1130572979190921">ip address 10.23.101.1 24</strong> [SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b133774347190921">dhcp select interface</strong> [SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1216259955190921">dhcp server gateway-list 10.23.101.2</strong> [SwitchB-Vlanif101] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b366557450190921">quit</strong></span></span> - 配置AP上线 # 创建AP组，用于将相同配置的AP都加入同一AP组中。
<span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1451837292190921">wlan</strong> [AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1710308668190921">ap-group name ap-group1</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b294415960190921">quit</strong></span></span># 创建域管理模板，在域管理模板下配置AC的国家码并在AP组下引用域管理模板。<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1815954045190921">regulatory-domain-profile name default</strong> [AC-wlan-regulate-domain-default] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1765454957190921">country-code cn</strong> [AC-wlan-regulate-domain-default] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b464951690190921">quit</strong> [AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1132959133190921">ap-group name ap-group1</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b4510754102210">regulatory-domain-profile default</strong> Warning: This configuration change will clear the channel and power configurations of radios, and may restart APs. Continue?[Y/N]:<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_zh-cn_task_0175818418_b17491131153716">y</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b101836067190921">quit</strong> [AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b465166413190921">quit</strong></span></span># 配置AC的源接口。V200R021C00版本开始，配置CAPWAP源接口或源地址时，会检查和安全相关的配置是否已存在，包括DTLS加密的PSK（AC和AP的DTLS加密使用的预共享密钥）、AC间DTLS加密的PSK（AC间隧道DTLS加密使用的预共享密钥）、登录AP的用户名和密码、全局的离线管理VAP的登录密码，均已存在才能成功配置，否则会提示用户先完成相关的配置。
<span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b806281647190921">capwap source interface vlanif 100</strong> Set the DTLS PSK(contains 6-32 plain-text characters, or 48 or 68 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):******Set the DTLS inter-controller PSK(contains 6-32 plain-text characters, or 48 or 68 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):******Set the user name for FIT APs(contains 4-31 plain-text characters, which can only include letters, digits and underlines. And the first character must be a letter):adminSet the password for FIT APs(plain-text password of 8-128 characters or cipher-text password of 48-188 characters that must be a combination of at least three of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):********Set the global temporary-management psk(contains 8-63 plain-text characters, or 48-108 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):********</span></span># 开启CAPWAP DTLS不认证方式。（V200R021C00及之后版本）<span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b15163144818377">capwap dtls no-auth enable</strong></span></span>V200R021C00版本开始，AC默认开启CAPWAP控制隧道的DTLS加密功能。开启该功能，添加AP时AP会上线失败，此时需要先开启CAPWAP DTLS不认证方式让AP上线，以便AP获取安全凭证，AP上线后应及时关闭该功能，避免未授权AP上线。
# 在AC上离线导入AP，并将AP加入AP组“ap-group1”中。假设AP的MAC地址为00e0-fc76-e360，并且根据AP的部署位置为AP配置名称，便于从名称上就能够了解AP的部署位置。例如MAC地址为00e0-fc76-e360的AP部署在1号区域，命名此AP为area_1。ap auth-mode命令缺省情况下为MAC认证，如果之前没有修改其缺省配置，可以不用执行ap auth-mode mac-auth。
AP认证模式为不认证时（ap auth-mode no-auth），只要AP接入网络和AC互通，即可自动上线，无需手动添加AP，或者手动对未认证通过的AP信息进行确认，可简化配置过程。但该方式存在安全风险，需确保网络环境安全，网络内无规划外的AP存在，否则建议用户使用更安全的MAC认证或SN认证。
举例中使用的AP，射频0为2.4GHz射频，射频1为5GHz射频。
<span style="color:#333333"><span style="background-color:#dddddd">[AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b763711121190921">wlan</strong> [AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1389711844190921">ap auth-mode mac-auth</strong> [AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1382708357190921">ap-id 0 ap-mac 00e0-fc76-e360</strong> [AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1272920990190921">ap-name area_1</strong> Warning: This operation may cause AP reset. Continue? [Y/N]:<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_zh-cn_task_0175818418_b460951517190906">y</strong> [AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b614746147190921">ap-group ap-group1</strong> Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration s of the radio, Whether to continue? [Y/N]:<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_zh-cn_task_0175818418_b1651706244190906">y</strong> [AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b959850628190921">quit</strong></span></span># 将AP上电后，当执行命令display ap all查看到AP的“State”字段为“nor”时，表示AP正常上线。<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b482061123190921">display ap all</strong> Total AP information: nor : normal [1] ExtraInfo : Extra information P : insufficient power supply -------------------------------------------------------------------------------------------------- ID MAC Name Group IP Type State STA Uptime ExtraInfo -------------------------------------------------------------------------------------------------- 0 00e0-fc76-e360 area_1 ap-group1 10.23.100.254 AirEngine8760-X1-PRO nor 0 10S - -------------------------------------------------------------------------------------------------- Total: 1</span></span># 关闭CAPWAP DTLS不认证方式。（V200R021C00及之后版本）<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b3420155514467">quit</strong> [AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1898583494615">undo capwap dtls no-auth enable</strong> [AC] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b9381917104714">wlan</strong></span></span> - 配置WLAN业务参数 # 创建名为“wlan-net”的安全模板，并配置安全策略。
举例中以配置WPA-WPA2+PSK+AES的安全策略为例，密码为YsHsjx_202206，实际配置中请根据实际情况，配置符合实际要求的安全策略。
<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1991067776190921">security-profile name wlan-net</strong> [AC-wlan-sec-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b851752672190921">security wpa-wpa2 psk pass-phrase YsHsjx_202206 aes</strong> [AC-wlan-sec-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b337241812190921">quit</strong></span></span># 创建名为“wlan-net”的SSID模板，并配置SSID名称为“wlan-net”。<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b69022931190921">ssid-profile name wlan-net</strong> [AC-wlan-ssid-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b36723145190921">ssid wlan-net</strong> [AC-wlan-ssid-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1738903244190921">quit</strong></span></span># 创建名为“wlan-net”的VAP模板，配置业务数据转发模式、业务VLAN，并且引用安全模板和SSID模板。<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1964707822190921">vap-profile name wlan-net</strong> [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1849868164190921">forward-mode direct-forward</strong> [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b166547162190921">service-vlan vlan-id 101</strong> [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b7899292190921">security-profile wlan-net</strong> [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b164868007190921">ssid-profile wlan-net</strong> [AC-wlan-vap-prof-wlan-net] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_b1178727990190921">quit</strong></span></span># 配置AP组引用VAP模板，AP上射频0和射频1都使用VAP模板“wlan-net”的配置。<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b2051092768190921">ap-group name ap-group1</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1753511747190921">vap-profile wlan-net wlan 1 radio 0</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1212706755190921">vap-profile wlan-net wlan 1 radio 1</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b729861449190921">quit</strong></span></span> - 配置AP射频的信道和功率
射频的信道和功率自动调优功能默认开启，可自动选择AP最佳信道和功率，除高密外的覆盖场景均建议使用自动调优功能。完成业务配置后，应立即进行一次调优。
如果有特别需求不使用自动调优，而是配置固定信道功率，则需关闭自动调优功能。举例中配置固定信道功率的步骤仅为示例，用于说明如何配置，实际配置中应严格按照网规结果，为每台AP分别配置信道功率。
更多配置可参考《WLAN网络优化》中的射频调优。
- 配置自动调优，自动选择AP最佳信道和功率（默认开启） # 开启AP射频的信道和功率自动调优功能。默认开启。
<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1470083908190921">ap-group name ap-group1</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b2057447356190921">radio 0</strong> [AC-wlan-group-radio-ap-group1/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b708023704190921">calibrate auto-channel-select enable</strong> [AC-wlan-group-radio-ap-group1/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b2110205126190921">calibrate auto-txpower-select enable</strong> [AC-wlan-group-radio-ap-group1/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b276683270190921">quit</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b803857613190921">radio 1</strong> [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1438374519190921">calibrate auto-channel-select enable</strong> [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1859980560190921">calibrate auto-txpower-select enable</strong> [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b677098010190921">quit</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b7872310190921">quit</strong></span></span># 手动触发一次射频调优。
<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1693505529190921">calibrate manual startup</strong> Warning: The operation may cause business interruption, Continue? [Y/N]:<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b2732191411564">y</strong></span></span># 待执行手动调优一小时后，调优结束。可配置射频调优模式为定时调优，并将调优时间定为用户业务空闲时段（如当地时间凌晨00:00-06:00时段）。默认每天03:00:00开始自动进行射频调优。<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1443027864190921">calibrate enable schedule time 03:00:00</strong></span></span> - 配置固定信道功率 # 关闭AP射频的信道和功率自动调优功能。
<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b172936473414">ap-group name ap-group1</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1429315453416">radio 0</strong> [AC-wlan-group-radio-ap-group1/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b7293444345">calibrate auto-channel-select disable</strong> [AC-wlan-group-radio-ap-group1/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b629315483417">calibrate auto-txpower-select disable</strong> [AC-wlan-group-radio-ap-group1/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b629354173412">quit</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b12294144173411">radio 1</strong> [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b729444133413">calibrate auto-channel-select disable</strong> [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1929404153415">calibrate auto-txpower-select disable</strong> [AC-wlan-group-radio-ap-group1/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b172941243345">quit</strong> [AC-wlan-ap-group-ap-group1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b62943413412">quit</strong></span></span># 按照网规结果中每台AP的信道功率，为每台AP分别配置其射频0和射频1的信道功率。<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b119411134143316">ap-id 0</strong> [AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1594163483320">radio 0</strong> [AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1594123417338">channel 20mhz 6</strong> Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_zh-cn_task_0175818418_b1384307436190906">y</strong> [AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b2941163412335">eirp 127</strong> [AC-wlan-radio-0/0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b694119340333">quit</strong> [AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b33229250190921">radio 1</strong> [AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b201103780190921">channel 20mhz 149</strong> Warning: This action may cause service interruption. Continue?[Y/N]<strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_zh-cn_task_0175818418_b1384307436190906_1">y</strong> [AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b652286665190921">eirp 127</strong> [AC-wlan-radio-0/1] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b1440636620190921">quit</strong> [AC-wlan-ap-0] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912356_b904227301190921">quit</strong></span></span>
- 配置自动调优，自动选择AP最佳信道和功率（默认开启）
- 验证配置结果
WLAN业务配置会自动下发给AP，配置完成后，通过执行命令display vap ssid wlan-net查看如下信息，当“Status”项显示为“ON”时，表示AP对应的射频上的VAP已创建成功。
<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b367333496190921">display vap ssid wlan-net</strong> WID : WLAN ID -------------------------------------------------------------------------------- AP ID AP name RfID WID BSSID Status Auth type STA SSID -------------------------------------------------------------------------------- 0 area_1 0 1 00E0-FC76-E360 <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1874482883190921">ON</strong> WPA/WPA2-PSK 0 wlan-net 0 area_1 1 1 00E0-FC76-E370 <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1628414885190921">ON</strong> WPA/WPA2-PSK 0 wlan-net ------------------------------------------------------------------------------- Total: 2</span></span>STA搜索到名为“wlan-net”的无线网络，输入密码YsHsjx_202206并正常关联后，在AC上执行display station ssid wlan-net命令，可以查看到用户已经接入到无线网络“wlan-net”中。
<span style="color:#333333"><span style="background-color:#dddddd">[AC-wlan-view] <strong id="ZH-CN_TASK_0180383109__zh-cn_task_0176912347_zh-cn_task_0176912351_b1120837202190921">display station ssid wlan-net</strong> Rf/WLAN: Radio ID/WLAN ID Rx/Tx: link receive rate/link transmit rate(Mbps) --------------------------------------------------------------------------------- STA MAC AP ID Ap name Rf/WLAN Band Type Rx/Tx RSSI VLAN IP address --------------------------------------------------------------------------------- 00e0-fcc7-1e08 0 area_1 1/1 5G 11n 46/59 -68 101 10.23.101.254 --------------------------------------------------------------------------------- Total: 1 2.4G: 0 5G: 1</span></span>
配置文件
-
<span style="color:#333333"><span style="background-color:#dddddd"># sysname SwitchA # vlan batch 100 to 101 # interface GigabitEthernet0/0/1port link-type trunkport trunk pvid vlan 100port trunk allow-pass vlan 100 to 101port-isolate enable group 1 # interface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan 100 to 101 # return</span></span> -
<span style="color:#333333"><span style="background-color:#dddddd"># sysname SwitchB # vlan batch 100 to 101 # dhcp enable # interface Vlanif101ip address 10.23.101.1 255.255.255.0dhcp select interfacedhcp server gateway-list 10.23.101.2 # interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 100 to 101 # interface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan 100 # interface GigabitEthernet0/0/3port link-type trunkport trunk allow-pass vlan 101 # return</span></span> -
<span style="color:#333333"><span style="background-color:#dddddd"># sysname Router # vlan batch 101 # interface Vlanif101ip address 10.23.101.2 255.255.255.0 # interface GigabitEthernet1/0/0port link-type trunkport trunk allow-pass vlan 101 # return </span></span> -
<span style="color:#333333"><span style="background-color:#dddddd">#sysname AC # vlan batch 100 to 101 # dhcp enable # interface Vlanif100ip address 10.23.100.1 255.255.255.0dhcp select interface # interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 100 # capwap source interface vlanif100 # wlansecurity-profile name wlan-netsecurity wpa-wpa2 psk pass-phrase %^%#m"tz0f>~7.[`^6RWdzwCy16hJj/Mc!,}s`X*B]}A%^%# aesssid-profile name wlan-netssid wlan-netvap-profile name wlan-netservice-vlan vlan-id 101ssid-profile wlan-netsecurity-profile wlan-netregulatory-domain-profile name defaultap-group name ap-group1radio 0vap-profile wlan-net wlan 1radio 1vap-profile wlan-net wlan 1ap-id 0 type-id 128 ap-mac 00e0-fc76-e360 ap-sn 210235554710CB000042ap-name area_1ap-group ap-group1radio 0channel 20mhz 6eirp 127calibrate auto-channel-select disable calibrate auto-txpower-select disableradio 1channel 20mhz 149eirp 127calibrate auto-channel-select disable calibrate auto-txpower-select disable # return</span></span>
